Any idea what could be causing my k2max to dig into the bed right before print? After the filament purge and nozzle clean it goes to right front corner and almost levels nozzle but digs into bed and entire head bends a bit the starts to print normally.
@mayogaming1488
2 ай бұрын
Hello im new to 3D printers and my printer carved the bed i heard that i should adjust Z offset but i just don't understand what value im suppsed to input any help is much appreciated
@romemakes794
4 ай бұрын
Is extrude just pulling the filament into the head? You just have to keep tapping "extrude" I guess?
@carlosluisdiazcastro816
6 ай бұрын
215 c for PLA smart materials????
@jorgegokuZ
8 ай бұрын
Once the initial calibration and the first printing are done... Do you have to calibrate again when you turn on? Or what should be done?
@CyberLiendre
7 ай бұрын
You don't have to do anything, just make sure the Z-Offset is correct.
@jorgegokuZ
7 ай бұрын
Gracias . Thanks
@gunnarbeddoes13
8 ай бұрын
Is this a good printer for a beginner?
@hedgehogform
8 ай бұрын
Honestly. Yes. Only though if you plan to print big things. But I had a Ender 3 V2 but I'm planning to upgrade to this which blows the ender 3 v2 out of the water. Even with bl touch installed.
@CyberLiendre
8 ай бұрын
I also came from an ender 3 pro, and this one is wonderful. Double axis, auto level, direct extruder... You will not regret
@zhelyoangelinov8330
8 ай бұрын
The music is quite annoying. Was hoping to hear the sound of the printer working.
@CyberLiendre
8 ай бұрын
I'm sorry about the sound
@CyberLiendre
8 ай бұрын
kzitem.info/news/bejne/rnqrsIOGk3Wom3o
@carlosluisdiazcastro816
6 ай бұрын
215 grados para material smart materials??
@CyberLiendre
6 ай бұрын
Voy alternado temperaturas dependiento de la marca. Ahora uso el sunlu y estoy a 215 la primera capa y luego a 200. La cama a 60 y perfecto
@carlosluisdiazcastro816
6 ай бұрын
@@CyberLiendre pero para la marca smart material que vi que tienes puesto ese en el video
@CyberLiendre
6 ай бұрын
@@carlosluisdiazcastro816 pues los parámetros eran casi idénticos, con ese lo probé en varios archivos y la configuración era la misma. Tienes problemas con el?
@CyberLiendre
6 ай бұрын
Empecé a hacer pruebas con 220 y luego a 215, para ver cómo respondía la máquina, pero a esa temperatura con el paso de las horas me provocaba atascos en el nozzle, hasta que fui bajando y logrando que todo fuera bien
@carlosluisdiazcastro816
6 ай бұрын
@@CyberLiendre si tengo el pla normal con la anycubic kobra max 2 y queria saber si me podrias decir mas o menos los parametros
@jorgegokuZ
8 ай бұрын
Pues a mí me ha arañado toda la base ...no me ha hecho bien los primeros pasos y lo he hecho igual
@CyberLiendre
7 ай бұрын
Pues deberas ajustar el Z-Offset para eviar eso
@jorgegokuZ
7 ай бұрын
The problem was that it did not come with home made, I had to do home xy and home z and home all and then the initial calibration... They sent me another sheet of magnetic base
Пікірлер: 28