AquaPhoenix P90 Features:
● RO+UV+UF with TDS adjustment.
● Inbuilt Sediment cum pre-filter, so external pre-filter is not required.
● UV protected tank.
● TDS adjustment through UF.
● Auto flushing for membrane.
● Digital Display.
● 10 Ltr storage tank.
● Easy to change filters.
● No technician required for filter change.
● Input water can be connected from left or right.
● Power can be connected from left or right.
● Reject water can be taken out from left or right.
● Strong hanging bracket.
● Easy to open.
● Vertical Filters.
● No screws in RO cabinet. Everything is press fit.
● Sweet Water.
Instructions For Installation :
1) Take RO out of the Box and packing.
2) Open front cover ( No Screws) only press fit
3) Open rear board ( No Screws) only press fit
4) Separate middle frame & water tank ( No Screws) only press fit
5) Water tank consists of all accessories. Take out all accessories.
6) Connect float switch to middle frame and connect its wire to display
panel.
7) Connect tap to the water tank.
8) Put middle frame on water tank (No Screws) only press fit
9) Fit rear board (Only press fit)
10) Put sticker on the wall and do drilling as per the sticker, fit 2 hanging
brackets on wall and hang RO water purifier on wall.
11) Connect inlet cock / Diverter Valve tap at sink.
This RO has inlet on both sides, left and right, use one as per inlet tap
position, close other with stopper.
Take power cord out from left or right as per your power supply
availability. Take only enough wire out keeping extra inside.
12) Take reject out as per your convenience from left or right
13) Turn ON the water & Power supply.
Display Details:
1. POWER : It is a touch switch to turn RO ON/OFF.
2. UV : It is a touch switch to turn UV light ON/OFF. But when UV has
to be ON it remains ON only, you can't turn it OFF. After tank
full UV remains ON for 20min. then turn OFF, and after every
4 hours it turns ON for 20min.
3. PURIFYING : These indicators show that RO water purifier is purifying the
water.
4. TANK EMPTY : This LED will blink when tank is empty.
5. FLUSHING : This purifier flushes the membrane on switching the power
ON and when the tank fills completely, for 18 seconds.
6. SERVICE : Needs service (For details please see in about display)
7. TANK FULL : This LED blinks when tank is full.
About Display:
• On power ON all LEDs Glow.
• Purifier will do membrane flushing for 18 Seconds.
• Tank empty LED is ON because tank is empty.
• Now purification is on but purifying LEDs are not glowing.
• Purifying LEDs will glow when water will touch lower float.
• After around 30 minutes tank will become full.
• Purifier will go to membrane flushing for 18 Sec.
• Now tank full LED will glow.
• If you take water out of tank, other brand purifiers will generally start
purifying immediately but this RO will not. Purification of RO will start
only when water will go below lower float [After taking 6 liters out of
tank].
• Again, tank will become full and membrane will get flushed. It means
after purifying 6 liters of water every time, membrane gets flushed
hence improving membranes life.
There can be three Faults indicated by the display:
1) Service LED is glowing and Buzzer is continuously ON
Reason - You have emptied the tank or initially it is empty. Present
scenario is, water purifier is purifying the water, tank empty LED is
ON, purifying LED is OFF, in 25 minutes water in tank should touch
Lower float but, if it does not touch means purified water is not
coming to the tank or the flow rate of purified water has decreased
drastically.
Possible Problems
1) Inlet water cock is off.
2) Overhead tank is empty.
3) Filters are blocked.
4) Pump is not working.
So, solve the problem & Restart the RO.
2) All LEDs are flashing and buzzer is continuously ON
Reason - This indicates that your purifying water speed normally 12
Ltr/Hr has become too low
Your purification is ON for 90 minutes and still your tank has not
become full. In normal condition tank should become full in 30
minutes.
Possible Problems
1) Filters are blocked. Needs to be changed.
By turning power OFF and ON again, your purifier will start
working again. But after 90 minutes same problem will arise so
change of filters is mandatory.
3) 6 Small purifying LEDs start flashing and buzzer is ON
continuously.
Reason - Float switch of purifier is faulty and needs to be changed
Негізгі бет AquaPhoenix P90 RO Water Purifier Installation Video
Пікірлер: 16