I go to try it this evening Thanks for this arducopter setup TIP for calibration error
@nighthawkvs
3 жыл бұрын
You are very welcome. Hope it helps.
@rongeernaert1208
3 жыл бұрын
@@nighthawkvs it did help but I had lucky that all my 8 props are removed because TAER and 2 where wrong and the right whas set at power so with dissabled safety switch all motor turning half power after restart without arming !
@nighthawkvs
3 жыл бұрын
@@rongeernaert1208 Motors turning without being armed isn't good. Never seen that before. Also not sure what would make the autopilot outputs bleed a PWM signal or a signal of any kind. kzitem.info/news/bejne/lmqhn4KdmGaDgKA
@rongeernaert1208
3 жыл бұрын
@@nighthawkvs Thanks for the Tip, I'm an old starter with a selfbild X8 quad copter , and it comes not level from the ground after calibration all props good mounted and good turning, but a blue led on my Pixhawk clone 2.4.8
@wellsjaxton5570
3 жыл бұрын
i guess I am kinda off topic but does anyone know of a good website to stream newly released movies online?
@djsolstice8964
Жыл бұрын
Thanks, it would have been great to see a live demo to.
@nighthawkvs
Жыл бұрын
I had planned that video soon after this one but the Flame Wheel just did not want to be resurrected again. Just set it aside for now yesterday. ☹ Do plan a top to bottom 7 inch Quad build in 2023 that will show everything.
@djsolstice8964
Жыл бұрын
@Vernon Silvers sounds great, can't wait.
@nighthawkvs
Жыл бұрын
@@djsolstice8964 Actually the Flame Wheel is still all together. I will try and make a video using it for you. 😊
@nighthawkvs
Жыл бұрын
I made a video. trouble is that my ESC’s just calibrated with no effort at all. I then went on to tell things that might go wrong. If you have problems, I also added a way to get help. kzitem.info/news/bejne/r5uosa2Af3mff2k
@George25
3 ай бұрын
Thank you very much, very helpful ,I shall try it 👍
@nighthawkvs
3 ай бұрын
Thank you very much for the kind comment. Let me know if you have problems. Also know that many of the new BLHeli and DShot ESC's don’t require calibration and the ArduPilot ESC calibration will fail in various ways. This failure is not a problem because they are self-calibrating.
@user-rr4jn9po6g
Жыл бұрын
Thank you sir 🎉 I learn from your esc calibration video 🎉
@nighthawkvs
Жыл бұрын
You are welcome. I am glad.
@rongeernaert1208
3 жыл бұрын
I've read on internet that my 8 DYS 40 amp OPTO ESC don't need Calibration , only just what you say in this Video Thanks
@nighthawkvs
3 жыл бұрын
You're welcome
@tysonmcphee6376
2 ай бұрын
Hi, looking for what port I plug my esc into? Holy Roman 6c thanks
@jamesmason7124
5 ай бұрын
Hello from New Mexico. I'm building a 4 inch micro long distance Arducopter drone, I'm using the Flywoo Explorer LR 4 V2 with Flywoo Dave-C-FPV 1404 v2 2750kv motors, matek h743 mini flight controller and i need a recommendation for a 32 bit 20by20mm m2 mounted esc. Can you please help me with a recommendation
@nighthawkvs
5 ай бұрын
I used this one on my little 5 inch with great success. shop.iflight.com/BLITZ-Mini-E55-4-IN-1-2-6S-ESC-Pro1663?search=BLITZ%20Mini%20E55%204-IN-1%20ESC%20
@FotoRilieviDroni
3 жыл бұрын
I have a pixhawk 2.4.8 and 4 esc hobbywing 40A... I'm trying to calibrate a drone 4 propeller but no one of this sistem has worked. Any other idea? The setting "normal" or "one shot" etc what does it means? sorry my english
@nighthawkvs
3 жыл бұрын
You can always calibrate with just a rc receiver.
@heythatguy6
3 жыл бұрын
Thanks for shedding light on this! Ardupilot doesn’t mention this step. Does this method work with Herelink?
@nighthawkvs
3 жыл бұрын
Yikes. I didn't know that was public. It was an answer to a specific question by someone. Herelink is a video transmission system, this was a person who had trouble getting an ESC to calibrate.
@heythatguy6
3 жыл бұрын
Well it’s out in the open. I tried this last night and it worked using my Herelink controller. Now I have to sort my PreArm: throttle too high issue. Thanks!
@nighthawkvs
3 жыл бұрын
@@heythatguy6 Cool. Always good when things work. I had not heard of Herelink until yesterday. Looks good. airsupply.com/product/herelink-pixhawk-remote-controller-hd-transmitter/
@heythatguy6
3 жыл бұрын
@vernon silver it’s a cool setup for sure. Would you know how I can solve my throttle too high prearm error?
@nighthawkvs
3 жыл бұрын
@@heythatguy6 Can you describe the problem or post a video? Sounds like you are saying that Arducopter won't arm because the throttle is high when it isn't. I would be interested to see what the throttle channel output is. kzitem.info/news/bejne/xKanvaqrpWt3doo
@jorgemendes2611
2 жыл бұрын
HELLO, CAN YOU HELP ME? THE APM 2.6 PLATE APPEARS IN THE MISSION PLANNER, WITH A LOT OF INCLINATION IN REFERENCE TO THE HORIZON LINE. WHEN CALIBRATING THE ACCELEROMETRO IN THE MISSION PLANNER, ALWAYS FAILS. I CAN'T CALIBRATE THE ACCELEROMETRO. YOU KNOW HOW I CAN FIX THIS???
@nighthawkvs
2 жыл бұрын
What version of ArduCopter?
@mergevlogs1799
Жыл бұрын
Thank you soo much Sir
@nighthawkvs
Жыл бұрын
You are most welcome.
@technicalboysujitkumar2448
11 ай бұрын
Sir my drone is not calibrating
@nighthawkvs
11 ай бұрын
What ESC are you using? Most are digital now and won’t because they calibrate themselves. The Docs have not been changed to reflect that since about 2016 or so.
@harshalaachrekar840
2 жыл бұрын
i have Simonk 30A ESC and facing calibration error on mission planner ... kindly help
@nighthawkvs
2 жыл бұрын
I had a lot of trouble calibrating my ESC on the Mini Talon recently. I ended up putting the platform in manual mode at startup and calibrated it that way. But I didn’t make a video of it because it was not an approved method of calibrating the ESC and I didn’t want to lead others down a wrong road. Watch this video and tell me IF this is the kind of error you are getting. Then we can work forward from there if it is or go in another direction if it isn’t. kzitem.info/news/bejne/wKeGrIeIZoZopm0
@nighthawkvs
2 жыл бұрын
This is long and a first draft. But it is what I can find that may help. kzitem.info/news/bejne/05-Q2HyPmn-FYJw
Пікірлер: 45