A good project for developing my skill in Arduino... it also helps me to gain knowledge by solving problems. Problems faced (and solutions) 1 - AT mode doesn't open - check the module is HC 05 or 06. the methods are different for both (There are many method to do this.. check it one by one) 2 - Program doesn't upload successfully - check the options in tools section of Arduino before upload (port, board, processor etc...) 3 - modules didn't turn on - check our connections properly (better if use multimeter) 4 - motors doesn't turn properly - change polarity of motors to motor driver by interchanging their wires 5 - motors doesn't work properly - check the voltage and current of battery - it only works in rechargeable battery since it has high current than normal battery if facing problems - use our internet to solve it... we need to face problems for final victory... I hope this helps
@Falcon_X1
Жыл бұрын
@hash pin this because it may be helpful for others
@hashincludeelectronics
Жыл бұрын
Well done and I am glad that after facing so many hurdles you made it successfully 👏🏻👏🏻👍🏻. And thank you very much for sharing your experience . These findings will definitely help others.
@Falcon_X1
Жыл бұрын
@@hashincludeelectronics 😀
@slyasastech
Жыл бұрын
True😊❤
@Nejtak853
3 ай бұрын
After all the videoes i have seen on youtube, and after 2 days of very hard working, your video sir, has been the only one that have worked 100% correctly. I dont know how to thank you, i have exam soon, so this video has helped me alot
@hashincludeelectronics
3 ай бұрын
Thank you so much for your comments . I am glad this video is helping you 👍🏻👏🏻. All the best for your exam too .please do share the channel among your friends circle as well 🙂
@chyontech7307
2 жыл бұрын
Some, because of the problem, I will not be online for 2 months, I will not use phone, laptop, I will miss your videos, a lot, but when I come back, I will watch all your videos, eat well, friend.
@hashincludeelectronics
2 жыл бұрын
Take care 👍🏻
@shaikafzal2454
6 ай бұрын
For getting the address of hc05 use "AT+ADDR?" in the video they have given "AT+ADDR" which give error
@hashincludeelectronics
6 ай бұрын
It’s good to always correct the commands 👍🏻👏🏻. Thanks to sharing .
@HACKERANUJ-vk3xb
Ай бұрын
BRO PLEASE MAKE A VIDEO ON QUESTION ANSWERING ROBOT USING NANO . THIS WILL IMPROVE YOUR AND ALSO MY KNOWLEDGE. PLEASE BRO. BIG FAN!!
@hashincludeelectronics
Ай бұрын
Nice idea . Will try that 👍🏻👏🏻
@fouzanjaved5441
2 жыл бұрын
Love the Arduino Bluetooth Car using the HC05 Master-Slave Transmitter Receiver robot. You should attach the 6-dof robotic arm on the Arduino Bluetooth Car using the HC05 Master-Slave Transmitter Receiver robot to look even more advanced.
@hashincludeelectronics
2 жыл бұрын
Thank you 👍🏻. I agree. I personally liked this car and it’s easy to handle it with joystick remote control. There is video on my channel of robotic arm car but with esp32 and PS3 controller . Will try to add that arm on this car as well . Stay tuned .
@fouzanjaved5441
2 жыл бұрын
@@hashincludeelectronics Sir, what courses do you do to get into the robotics field, tell me?
@hashincludeelectronics
2 жыл бұрын
@@fouzanjaved5441 You can check the tutorials and videos available online about different microcontroller modules like Arduino , esp32, raspberry pi etc. And check how different sensors work. Get some knowledge about different motors working. As far as programming is concerned you need to learn c++ for Arduino. May be check w3schools website. There may be some other courses on robotics available online which I am not aware about right now . But will let you know if I find something more. Learn slowly and regularly, you will be successful 👍🏻
@vedantsharma4089
Жыл бұрын
Can you please tell the code of same project by using shield motor driver L293D
@hashincludeelectronics
Жыл бұрын
This project uses L298N module which is also cheap . I would recommend to use the same module to avoid any issue. However I have not used L293D module ever . So unfortunately I am not sure about it . 👏🏻👍🏻
@I.C.B_records
6 ай бұрын
Can we use the hc06 like a slave ? How can i proceed for to pairing hc06 and hc05
@hashincludeelectronics
5 ай бұрын
Please try that 👍🏻👏🏻
@aaroonikrishna6618
10 ай бұрын
Hello sir nice video i have one question i dont want to use 7 12 v dc battery can i use li ion battery
@hashincludeelectronics
10 ай бұрын
Yes you can 👍🏻👏🏻
@Nejtak853
3 ай бұрын
all the AT-commands work, execpt the "AT+RMAAD" command. i doesnt show a "ok" sign. What should i do?
@TechnoShuvo360
2 жыл бұрын
Amazing invention... Good luck friend..
@hashincludeelectronics
2 жыл бұрын
Thank you very much 👍🏻
@HACKERCOMPETITION
Ай бұрын
Please make a video on obstacle avoiding car with solar panel
@hashincludeelectronics
Ай бұрын
@@HACKERCOMPETITION there is already video on my channel on obstacle avoiding car . You can easily add solar panel on it . Give it a try 👍🏻👏🏻
@ricardogarfias9349
2 күн бұрын
Hi! Thanks for the video. When the HC-05 module is blinking every two seconds (supposedly indicating that is on AT mode) I enter the "AT" command in the Serial Monitor and I receive OK. The problem appears when I enter the "AT+RMAAD" or any other AT command. I always receive the ERROR:(O) response. What can I do?
@jakerooni5542
5 ай бұрын
Hi, I've followed this step by step and the car is functioning properly. I'm wondering on how I can make it go any faster? Yours seems a lot faster than mine, I imagine it's because of the battery that I'm using, what specific battery are you using sir?
@hashincludeelectronics
5 ай бұрын
Yes I have used LiPo 3S battery in it which provides around 12V . That’s it why it is faster . 👍🏻👏🏻
@haroldo00027
Жыл бұрын
can I do this project with two Arduino Uno? using HC05(master) and HC06(slave)?
@hashincludeelectronics
Жыл бұрын
You can use Arduino Uno in this project . However not sure about HC06 . I would suggest use only HC05 to avoid any issues . 👍🏻👏🏻
@lukaspuhl556
3 ай бұрын
I just tried everything but my motors are moving uncontrolled all the time and they are changing directions for just a sec also. Do you have a solution for this?
@hashincludeelectronics
3 ай бұрын
Use rechargeable battery if not using already 👏🏻👍🏻
@arshdixit13
Жыл бұрын
hi sir what version of Arduino IDE did u use in the video??
@hashincludeelectronics
Жыл бұрын
Probably it’s shown in the video . Else I will check and confirm 👍🏻👏🏻
@AceNexy-Bhargav
3 ай бұрын
Hi bro! Awesome ved I have a doubt brother I am trying to make a project with Arduino mega which controls car and robotic arm Can I consider this transmitter for my project only to drive the car ??
@hashincludeelectronics
3 ай бұрын
Yes you can 👍🏻👏🏻
@adilfarooq1430
Жыл бұрын
Hi, did you face any delay in receiving signals to the slave hc05 on robot. I am getting delayed signals and at time it jams. What can be the issue?
@hashincludeelectronics
Жыл бұрын
Did you change the baud rate by any chance ? Low baud rate will cause this problem . Or you can add some delay of say 50 milliseconds in transmitter code after every transmission.
@adilfarooq1430
Жыл бұрын
@@hashincludeelectronics actually i bought a robot with an andriod app as a controller already provided to control via Bluetooth. I can't seem to make changes on the transmitter side. But I can make changes in Arduino code on the receiver side. Can you tell me what I can do, or I can share the code if you can look at it. Pls, send me your email?
@chaitnyasrivastava944
Жыл бұрын
Sir it's showing error 7 when I put mac address master hc05
@hashincludeelectronics
Жыл бұрын
Please check the video slowly and carefully to avoid any issue 👍🏻👏🏻
@letantru5106
3 ай бұрын
i have a problem, when my car just started, it runs normally but after that i can't controller, i press reset button on arduino board and it back to normal how can i fix that
@hashincludeelectronics
3 ай бұрын
Is the issue resolved ?
@gamesoccer5956
6 ай бұрын
Sir for both tarnsiver master slave code are same ?
@hashincludeelectronics
6 ай бұрын
Please check the video for this step 👍🏻👏🏻
@omsrivastava6684
6 ай бұрын
The Serial monitor is not responding when I uploaded the AT configuration code. I tried typing commands like AT, AT+ADDR but no response like Ok from serial monitor. what should I do?
@hashincludeelectronics
6 ай бұрын
Please check the baud rate selected . Also take a look at video for any missing step 👏🏻👍🏻
@AkashDas-vx2ph
2 жыл бұрын
Excellent sir ☺️
@hashincludeelectronics
2 жыл бұрын
Awesome 👍🏻
@sulav_gaming_yt5808
6 ай бұрын
Can you help me add a potentiometer on the controller that controls 2 servo motor on the car please
@hashincludeelectronics
5 ай бұрын
You can check my videos on controlling servo motor and add it in this project . Give it a try 👍🏻👏🏻
@lokeshkumaryadav2254
Ай бұрын
Can we do the same with bts7690 motor driver
@hashincludeelectronics
Ай бұрын
Unfortunately I am not sure about this driver 👍🏻👏🏻
@AceNexy-Bhargav
3 ай бұрын
Hi bro ! I hope u rem me but anyway bro how r u?? Bro can u pls say what is the approx range of this config?
@hashincludeelectronics
3 ай бұрын
I am good . How are you ? The approx range is standard Bluetooth range around 100 ft 👏🏻👍🏻
@sumitdpatel76
Жыл бұрын
Can i give power supply of 2200 mah lipo battery ?
@hashincludeelectronics
Жыл бұрын
Yes you can 👍🏻
@NEILMATHEW-e1r
Жыл бұрын
I am facing a problem. The car moves on its own even when the Joystick is not used. It starts moving after the master and slave are connected. I am using lithium battery of 3.7 volt for the receiver and a power plug of supply 12 volt for the transmitter. Please suggest what is the problem.
@hashincludeelectronics
Жыл бұрын
You need to use total 7-12v power supply at receiver . 👏🏻👍🏻
@NEILMATHEW-e1r
Жыл бұрын
What I meant was I am using a pair of 3.7 volt lithium battery. Sorry for the mistake
@anghelleonelretomoreno4966
Жыл бұрын
I have a similar problem, when the master is connected and the slave starts moving without using the joysticks and I can only control the direction of the car. Does anyone know how this can be fixed?
@dheerajdixit5411
Жыл бұрын
hi sir i have connected everything correctly the modules seem to connect but then only the master module is blinking and the slave stops blink hence the car does not work can you please help with that??
@hashincludeelectronics
Жыл бұрын
I would suggest to take a closer look into video again . This project is very involved and needs lot of attention . Please check video slowly and carefully again. Also make sure you use only rechargeable battery in your project 👍🏻👏🏻
@ashutoshdash1955
2 жыл бұрын
Hello I have a idea can u make a self Balancing bike which drive there are lot of video but none of them explain... So if u could try this out will be a great also it's will be something new thx
@hashincludeelectronics
2 жыл бұрын
That’s a nice idea . Thanks and Noted 👍🏻
@xpertgamer8431
Жыл бұрын
Can i use Arduino uno instead of nano in rc car fir hc 05 and motor sheild and joystick with nano...?
@hashincludeelectronics
Жыл бұрын
Yes you can use 👍🏻
@Fati-ok5ey
10 ай бұрын
Hi I have a problem, i did all th steps but my bleutooth slave show only numbers between 245 and 255 i don’t know why
@hashincludeelectronics
9 ай бұрын
Please follow the exact step as shown in video 👍🏻👏🏻
@ryangerken4251
Жыл бұрын
I don't have an arduino nano can I juse an arduino uno or is it only possible with arduino nano
@hashincludeelectronics
Жыл бұрын
You can use Arduino Uno 👍🏻👏🏻
@Falcon_X1
2 жыл бұрын
For all who got error while getting address of Bluetooth module... use this at command "AT+ADDR?" instead of "AT+ADDR" i wish it could help
@hashincludeelectronics
2 жыл бұрын
Thank you clarification and letting others know . Appreciated 👏🏻👍🏻
@Falcon_X1
2 жыл бұрын
@@hashincludeelectronics U are welcome
@justadude5160
Жыл бұрын
OMG THANK YOU VERY MUCH MINE WAS NOT WORKING THEN IT WORK THX UR THE BEST 😁😁😁
@Falcon_X1
Жыл бұрын
@@justadude5160 glad to hear that! keep building new things!
@kevinknight9994
8 ай бұрын
Anyone know how I can add the code to use 2 analog switches? I know the wiring just dont know how to add the code so it will send signal like the joysticks...
@hashincludeelectronics
7 ай бұрын
We are already using 2 joysticks here 👍🏻👏🏻
@iggyboyTV
Жыл бұрын
sir it is possible in this setup master and slave control,is control by mobile phone simultaenously?
@hashincludeelectronics
Жыл бұрын
I am not exactly sure on this 👍🏻👏🏻
@Nejtak853
3 ай бұрын
8:02 to these wires comes with the car package?
@hashincludeelectronics
3 ай бұрын
Yes 👍🏻👏🏻
@neuhold.m
9 ай бұрын
What should I do if I type AT in my serial monitor and nothing happens, I also get no „atSerial stardet at 38400“
@neuhold.m
9 ай бұрын
also my hc05 is blinking red and blue, but if i enable AT mode just like you, both lights blink in a sequence of 2 seconds
@hashincludeelectronics
8 ай бұрын
I would suggest to check video slowly and carefully to not miss any step 👍🏻👏🏻
@neuhold.m
8 ай бұрын
@@hashincludeelectronics already got it and everything works, great video👍🏽
@hashincludeelectronics
8 ай бұрын
@@neuhold.m nice job 👍🏻👏🏻
@technicaldilendra5737
Жыл бұрын
I try to make this project everything is fine but I face problem for steering control this car moving only forward and backward steering not working I try everything wire changing
@hashincludeelectronics
Жыл бұрын
Steering is on other joystick.
@darkangel6559
7 ай бұрын
Can we connect transmitter to laptop for power instead of batteries?
@hashincludeelectronics
7 ай бұрын
Yes you can 👍🏻👏🏻
@darkangel6559
7 ай бұрын
Thank You@@hashincludeelectronics
@hashincludeelectronics
7 ай бұрын
@@darkangel6559 welcome 🙏
@ChauhanIshanShorts
Жыл бұрын
Good ideas👍👍👍
@Manish_Kumar2022
Жыл бұрын
Bro when i connect my battery with my l298n motor module my Bluetooth stops working and when i connect the usb my Bluetooth starts working and connects to the master but it's motor is not working
@hashincludeelectronics
Жыл бұрын
Which battery do you use ? Use only rechargeable battery because it supplies good current 👍🏻👏🏻
@Manish_Kumar2022
Жыл бұрын
@@hashincludeelectronics I used rechargeable battery and it starts working but controller is not functioning and when I connect my battery to vin it Bluetooth stops working
@davidoliveira5837
10 ай бұрын
when i put in the serial monitor the comand AT or AT+RMAAD or AT+ROLE=0 or AT+UART=38400,0,0 or AT+ADDR doesn´t show anything in the serial monitor ("the message: OK")
@hashincludeelectronics
10 ай бұрын
Please follow the video 👍🏻👏🏻
@shahnewajbd4623
7 ай бұрын
@@hashincludeelectronics when i type AT+ADDR it's reply me with error,,, what is the problem
@Fisicracks
7 ай бұрын
@@shahnewajbd4623 put AT+ADDR? tHE QUESTION MARK is missing, same error
@siddheshwarlondhe5319
2 жыл бұрын
Thank you so much
@hashincludeelectronics
2 жыл бұрын
No problem 👏🏻
@hoblau317
10 ай бұрын
why must be rechargeable battery ?
@hashincludeelectronics
10 ай бұрын
Rechargeable batteries provide good current and these have good capacity . Also these last longer . It solves many power related issues 👏🏻👍🏻
@davidjob8917
2 жыл бұрын
Nice project 👍
@hashincludeelectronics
2 жыл бұрын
Thanks for checking out the video 👍🏻👏🏻
@kamieldemeyer
Жыл бұрын
Would it be able to combine the arduino code from the NRF24L01 with the arduino code of the HC-05? I want to control my RC car with a controller (via the NRF24L01 module). And also be able to control it via an app (with the HC-05 module)
@hashincludeelectronics
Жыл бұрын
You can refer my videos for combination.
@xenonyoutub
Жыл бұрын
nice job man
@hashincludeelectronics
Жыл бұрын
Thank you! Cheers!
@tanaysuman8433
Жыл бұрын
Hi how many arduino nano u used in this arduino bluetooth car
@hashincludeelectronics
Жыл бұрын
2 Arduino nano . One at transmitter and another at receiver 👏🏻👍🏻
@letantru5106
7 ай бұрын
can u help me to use double L298N instead of one
@hashincludeelectronics
7 ай бұрын
Actually you can check my videos on mecanum wheels car where I have used 2 L298N modules . That will give you idea 👍🏻👏🏻
@letantru5106
7 ай бұрын
@@hashincludeelectronics ok guys, i have found the solution with that video, thanks for helping me
@hashincludeelectronics
7 ай бұрын
@@letantru5106 awesome 👏🏻
@gamingwithprakalp
Жыл бұрын
Nice
@hashincludeelectronics
Жыл бұрын
Thank you very much 👌🏻👍🏻
@delamercedjullianneapples.625
5 ай бұрын
is the code is plug in play?
@hashincludeelectronics
5 ай бұрын
Yes. However you need to do some setup like master slave configuration for Bluetooth modules . For that you will have to perform some additional steps shown in video . 👍🏻👏🏻. You can check my other Bluetooth car video where we don’t need such master slave additional set up 👍🏻
@himanshu015-x8v
10 ай бұрын
i used 2 motors for speed and 2 motors for steering can u provide code for that please
@hashincludeelectronics
9 ай бұрын
It’s not just providing code but it needs testing as well. I would suggest to take help of the existing code and make changes accordingly 👍🏻👏🏻
@616lizzie
2 жыл бұрын
Nice 👍🏻
@hashincludeelectronics
2 жыл бұрын
👍🏻👍🏻
@slyasastech
Жыл бұрын
How about the transmit range
@hashincludeelectronics
Жыл бұрын
It’s a classic Bluetooth communication which has range around 100 ft or so . 👍🏻👏🏻
@TECHAB254
2 жыл бұрын
Can bluetooth module be used again
@hashincludeelectronics
2 жыл бұрын
This project uses Bluetooth module only .
@LarsDeRuntz
2 жыл бұрын
Maybe this could be a self driving car too.
@hashincludeelectronics
2 жыл бұрын
👏🏻👏🏻
@ashirvadlokesh1038
Жыл бұрын
when i put AT+ADDR its coming error(0) can you help with this
@ashirvadlokesh1038
Жыл бұрын
Can you please help with this error
@MisterSob
10 ай бұрын
"AT+ADDR?" try this one
@SumanDevi-wq8hh
2 күн бұрын
Bro its showing error(7) while at+bind
@godgajet6763
10 ай бұрын
help im sending at but no response
@AbbasZeynalov-ik2mo
Жыл бұрын
nice
@hashincludeelectronics
Жыл бұрын
Thank you 🙏
@godgajet6763
2 жыл бұрын
do this code work on UNO3 ?
@hashincludeelectronics
2 жыл бұрын
Yes it works with Uno as well 👍🏻
@krishiprojuktitheindiangar9562
11 ай бұрын
My problem is solve thanks for reply 🥰
@hashincludeelectronics
11 ай бұрын
Awesome . Nice work 👍🏻👏🏻
@shlokdaga
2 жыл бұрын
What is its range to control?
@hashincludeelectronics
2 жыл бұрын
I tested for 60-80 ft
@Maharaj568
9 ай бұрын
Sir software upload nahi ho taha hai 😢😢
@hashincludeelectronics
9 ай бұрын
What issue are you facing ?
@shahnewajbd4623
7 ай бұрын
After try for it ,i can't use the hc05 module for other projects
@hashincludeelectronics
7 ай бұрын
You need to set the addresses and modes properly 👍🏻👏🏻
@shahnewajbd4623
7 ай бұрын
@@hashincludeelectronics please help me to make my hc05 useable with mobile phone
@Nejtak853
3 ай бұрын
AT+RMAAD does not work. no "ok" i showing up
@hashincludeelectronics
3 ай бұрын
Were you able to connect ?
@Nejtak853
3 ай бұрын
@@hashincludeelectronics I just skipped this step, and it worked
@hashincludeelectronics
3 ай бұрын
@@Nejtak853 awesome 🙌🏻
@ashikfahmin2776
2 жыл бұрын
how can i made this car with bts7960 module
@hashincludeelectronics
2 жыл бұрын
Unfortunately I am not familiar with this module so not able to comment . Please check some references.
@ashikfahmin2776
2 жыл бұрын
Ok... i will
@ashirvadlokesh1038
10 ай бұрын
Bro how to anti bind the bluetooth
@ashirvadlokesh1038
10 ай бұрын
I want to unpair the both slave and master
@hashincludeelectronics
10 ай бұрын
Please check for this step on internet 👍🏻👏🏻.
@krishiprojuktitheindiangar9562
11 ай бұрын
Diagram is not open please provide diagram
@hashincludeelectronics
11 ай бұрын
I just checked and it’s opening fine . Please check 👏🏻👍🏻
@krishiprojuktitheindiangar9562
11 ай бұрын
Please believe me diagram download is not done
@zofmod
2 жыл бұрын
U could use a ps3 or ps4 pad for your car aswell btw
@hashincludeelectronics
2 жыл бұрын
Yup . I have used those as well . Check my other videos related to ps3 and ps4 controller cars .
@zofmod
2 жыл бұрын
@@hashincludeelectronics i was just looking lol nice videos bro
@hashincludeelectronics
2 жыл бұрын
@@zofmod awesome
@zofmod
2 жыл бұрын
@@hashincludeelectronics im doing home assistant with my stuff here's a old video kzitem.info/news/bejne/wIiAzqKIraCEYG0
@aurobindo1231
2 жыл бұрын
Make temp and humidity sensor with bluetooth and android app
@hashincludeelectronics
2 жыл бұрын
Sure. Will try.
@aurobindo1231
2 жыл бұрын
@@hashincludeelectronics thanks
@TKherithEquwan
Жыл бұрын
Can you send the coding arduino?
@hashincludeelectronics
Жыл бұрын
Code and diagram link is provided in the description of the video 👍🏻
@TECHAB254
2 жыл бұрын
Error showing on AT+ADDR on serial monitor
@hashincludeelectronics
2 жыл бұрын
Thanks for checking the video 👍🏻 could you please share more details on this error ? Or send me screenshots of error on Instagram hashincludeelectronics
@TECHAB254
2 жыл бұрын
@@hashincludeelectronics solved
@hashincludeelectronics
2 жыл бұрын
@@TECHAB254 awesome 👏🏻
@TECHAB254
2 жыл бұрын
@@hashincludeelectronics but car was not working
@hashincludeelectronics
2 жыл бұрын
@@TECHAB254 keep trying. Use only rechargeable battery .
@baburaoamzire1730
21 күн бұрын
code upload nahin ho raha hai
@hashincludeelectronics
21 күн бұрын
Please check the video for details 👍🏻👏🏻
@sifurrahman1740
Жыл бұрын
❤
@istiyekahmedshayem7721
2 жыл бұрын
ভাই আমারে এটা বানাইয়া দিবেন
@tsgaming1v6
Жыл бұрын
4:39
@irpia7026
2 жыл бұрын
Awesome!
@hashincludeelectronics
2 жыл бұрын
Thank you very much 👍🏻👏🏻
@arhamjain3782
Ай бұрын
Ok isnt coming while typing AT
@hashincludeelectronics
Ай бұрын
Please follow the exact steps shown in video . Check video slowly and carefully for any missing steps 👍🏻👍🏻
@zofmod
2 жыл бұрын
You can connect multiple HC-05s with kzitem.info/news/bejne/yoN702eHq4JkaoY
@belaldurany5131
3 ай бұрын
Doesn’t work sorry
@hashincludeelectronics
3 ай бұрын
What issue are you facing ? 👍🏻👏🏻
@belaldurany5131
3 ай бұрын
@@hashincludeelectronics when typing “AT+RMAAD” ok is not showing up
@HP_HITLER
6 ай бұрын
Hello brother mera yho nahi chal raha
@hashincludeelectronics
6 ай бұрын
What issue are you facing ? Please check the video slowly and carefully again for any missing step 👍🏻👏🏻
@aaravakshayshah7527
Жыл бұрын
I am getting the error"reverse was not declared in this scope can you help me pls
@hashincludeelectronics
Жыл бұрын
Please check video and code properly for any missing step 👍🏻
Пікірлер: 199