I changed mine because I ripped them off by mistake.
@RYU47376
Жыл бұрын
Pads are probably $10 for like a3 size hahaha
@Safetytrousers
Жыл бұрын
@@RYU47376 Depends if you are paying more for higher thermal conductivity.
@SianaGearz
Жыл бұрын
If the ones that tore look and feel like tofu, then it was no mistake.
@prawny12009
6 ай бұрын
If it's from ali express it's most likely going to be fake.
@tourmaline07
Жыл бұрын
I really wish the AIBs certified thermal pads and thermal pastes/putties for use in reconditioning GPUs so there wouldn't be so much guesswork , which if it turned out wrong in terms of thickness and stiffness could break the GPU , or the VRAM from the board and turn hundreds of dollars into a paperweight. Would be so much easier if you bought some thermal grizzly and it was "approved for EVGA FTW3 models" or something like that
@weasle2904
Жыл бұрын
Very good idea, email thermal grizzly.
@silvershines
Жыл бұрын
GELID thermal pads are insanely good value; best for its price range. TekShinji did a comprehensive benchmark of several after-market pads, and the Gelid pads topped the chart in price/perf. But unintended effect of good pads: the heat still gets dumped onto the same heatsink -- so while it will help lower your VRM temps, it has an adverse effect of raising your core GPU temps at equilibrium a few degrees higher. Not too important in the grand scheme of things, but something to be mindful of.
@jackderke
Жыл бұрын
That´ll heavily depend on the cooler of the GPU. On something like a TUF 3080 were the memory and Core don´t have a directly connected cooler it improves both, as the thermal paste you´d use is likely better too. Also On my Strix card I´ve only seen lower temps on the core since I´ve replaced the pads. There is a reason for that too. Thermal transfer on a copper cooler is way higher while it has a lower temperature. Meaning if there isn´t 90-105°C memory but 68-74°C memory (numbers from my personal experience) then the cooler does have a lower overall temperature, meaning the core temp isn´t actually negatively effected at all.
@hoecage8781
Жыл бұрын
core being 3*c higher won't affect lifespan, vrms and memory are much more sensitive to heat
@josephdias5859
Жыл бұрын
polished copper shims on vram and the gpu die actually significantly drop temps over pads they need to make a pad with copper in it if they can make copper stretchy wastebands then a copper thermal pad should be no problem
@janemba42
Жыл бұрын
I don't see how this is an issue considering that's the entire point of those thermal pads even being there.
@kurohyuki5912
Жыл бұрын
I love these kind of videos. Not enough youtuber cover after market performance improvements.
@MarcoGPUtuber
Жыл бұрын
1:14 It's shaping up to be EXCITING times for Tech YES parts hunts with the flood of GPUs incoming!
@i_am_terom4810
Жыл бұрын
I remember the "70$ rx470", so i can't wait for the 170$ rx5700 haha
@gwinyne8221
Жыл бұрын
Just make sure you measure your thermal pads before you order. Too thick of a thermal pad will cause more issues than not changing them. Always check with your own card model and model number as each cooler and each 3000 series card will have a varied amount of thermal pad thickness. The aorus master 3070 to has 3 sizes, 1mm, 1.5mm and 3mm (for the backplate)
@michaelthompson9798
Жыл бұрын
I’ve switch my stock thermal pads on my rtx3080 and Ti models and seen between 7-12c lower temps under gaming loads. My Ti had some “meh” stock pads which actually replaced with Gelids and saw about 11-12c drop in memory temps. My Ti isn’t water cooled and using its stock 3-fan cooler. My 3080 is running about 7-10c cooler under gaming load and slightly lower again once I placed on an EK waterblock 😇🥰👍
@AmigaWolf
Жыл бұрын
@Swim Fan Yeah Linux is great, i use now Pop OS on both my computers, Game-PC and Mini Media/Console-PC, and i do not want to go back to Windows 11, it just works that great, and games run fantastic.
@AmigaWolf
Жыл бұрын
@Swim Fan Strange i do not have problems that constantly extensions keeps breaking or not working correctly, if that was happening, i would have not use Pop OS anymore. Yeah what do you expect from Google (Alphabet Inc), they life from stealing our data, and much more.
@kaptenhiu5623
Жыл бұрын
I replaced my thermal pads with copper shims, it's much better than any thermal pads I ever buy. The temperature drops from 80 C to 65 C. hotspot from 95 C to 75 C and VRAM temp from 82 C to 70 C compared to good thermal pad (Thermaltake). Copper has much better thermal conductivity and much cheaper too. I bought 10 pieces for less than 7$ total. The installation however is much harder than thermal pads. It's not for everyone.
@avoncompton2135
Жыл бұрын
Gelid pads are great!! Reduces 10c to 20c on air cooled cards VS stock pads depending on the make. Gigabyte pads aren't great on GDDR6X for instance on their Eagle models
@SkipsTinyBeard
Жыл бұрын
I did this on my old rx 580 and it worked extremely well. Bought 17w\mk pads and they worked great. Drastically brought temps down.
@jdogi1
Жыл бұрын
If you have a metal back plate, it help to put pads on the back side of the PCB to move some additional heat from the other side of those memory dies. I don't remember my exact results, but it was enough that I was happy with the time/effort invested. I also put some copper heatsinks on the outside of the back plate to help more. That GDDR6x makes some heat.
@DuneRunnerEnterprises
Жыл бұрын
VERY IMPORTANT !! The thickness of the thermal pads are can ,and WILL BE different. In order to know it,one of the sources is the tech support of the card maker.
@billpii6314
4 ай бұрын
Just repasted my 2080 ti and didn't touch the pads I just put new paste on the GPU and put it back togeather. Temps went from 82 down to 67-70 under full load. NICE! With that said the GPU came apart real clean and the old pads were completely fine, if they had ripped apart I would have changes them also but...they didn't :) All in all a great results with the old pads!
@tapts503
Жыл бұрын
Did the same thing with Gelid2.0mm on a used 3080 FE bought off eBay. It reduced the hotspot by 19 degrees. I don’t even worry about the heat anymore. Also, the FE cards are the worst to open up.
@jacqli69
Жыл бұрын
Gelid Ultimate 15W/mK pads are awesome. I've watched many comparisons between pads and Gelids were consistently the best, or within 1C difference with the best. While being much cheaper than the other premium thermal pads. I'm using those pads currently on the backside of my GPU after installing a big finned heatsink on the back of my 1060 6GB. It does its job really well. The heatsink on the back gets really hot to the touch without airflow (can't touch it for more than a couple seconds because it's hot). It definitely helps with cooling both the memory chips, as well as the GPU core. The effect would be even greater on more powerful cards than my 1060. I'd recommend doing this mod to anyone really.
@ps3customgamer
Жыл бұрын
I spent some time looking into this and the issue is the 2mm thickness of the pads in the reference design. My gigabyte model has a heatsink with a raised heatsink so the thermal pad can be 1mm. Copper shims from aliexpress with paste between the shim and heatsink and thinner pads would give better thermal transfer.
@802Garage
Жыл бұрын
I've seen from several sources that the cheaper GP-Extreme can actually be better. They are a softer material so they conform better and aren't as strict on exact pad height. Just a thought.
@MrMcGreed
Жыл бұрын
I changed the pads on my old 1080ti - bought it used in 2019. Dropped temps on mem by 4c.... not amazing results for the dollar... but fun to try out :)
@eliashowe7115
Жыл бұрын
You have to be really careful with choosing the right thermal pads, my gpu died after a day with the new thermal pads.
@shiftctrlhack
Жыл бұрын
That sounds more like a GPU problem if it hits high temperatures it should shut down it shouldn’t die. Unless the card it was already faulty. There’s a few good KZitem videos that show you all these different brands the squishiness and thickness of each so you can determine the correct thickness. Some of the 2MM are squishier than others or Stiffer.
@swizzler8053
Жыл бұрын
You had the wrong size?
@eliashowe7115
Жыл бұрын
@@swizzler8053 the thickness was right, but the original ones were more soft and more thermal conductive
@Globodyne
Жыл бұрын
If you mod something, you have to be prepared to buy it twice if it breaks, which begs the question, why didn't you just buy the better model, to begin with? People who mod are either rich, YOLOers, have had experience with other cheaper/expendable parts, or are KZitemrs with warehouses full of parts to work on.
@hadifelani
10 ай бұрын
@@eliashowe7115 dude many GPUs didn't have good paste or pads, even on top of the line GPUs. Not to mention that weather + humidity condition during shipping / storage can also affect their quality.
@gezt7528
Жыл бұрын
You should check out the K5-PRO viscous thermal paste for thermal pad replacement - it would be great to see a comparison
@donoteatmikezila
Жыл бұрын
It's important to measure the results under real-world use cases, not just synthetic memory tests. In many cases having much better thermals on the memory can actually lead to higher core temperature because the cooling solution is having to absorb much more heat. My 3080 Ti FE with new pads did drop memory temps down a staggering 20-30 degrees, but it also raised core temps by about 5-10, and this is with the exact correct thickness measured by myself and very careful and precise mounting of the cooling solution. This may not matter if your core usually doesn't get hot, but if you play at high resolutions and push the card you could actually be losing performance due to reduced thermal headroom on the core. If you are going to go the distance with new pads it may be prudent to go all the way and do a water cooling solution that can dump all that extra heat. I sort of regret my 3080 Ti FE. The FE cooler just does not keep up, and the stock pads are embarrassing.
@tech6294
Жыл бұрын
Great video as usual! ;)
@rileyhance318
Жыл бұрын
i changed the ones in my strix 3080 for a copper plate that was machined specifically for it. it dropped 30C easily. was at 105C and now its between 65-70C
@bombastinator1887
Жыл бұрын
Got the specs for that? It sounds like a good mod
@SirDaffyD
Жыл бұрын
Great video Brian. I've watched a few videos where they replace these pads with copper shims, and reduce temps around 20c or more on the 3080 & 3090 cards. Would be good to see you give that a try for comparison.
@andrewchong3333
Жыл бұрын
you look great bryan! after you left aus lol, no seriously your skin tone is shining
@EliteRock
Жыл бұрын
In recent years I've replaced all GPU and MB pads (VRM, chipset/PCH, VRAM) with GP Ultimate in both my last two machines. Even without sensors, using both the 'finger test' and an IR thermometer it's quite clear that (in most cases) there is pretty massive difference - the sinks are much warmer, 10°C or more. Unsurprisingly it's most pronounced where the original pads were the cheap, rubbery silicone ones. Gelid GP Extreme and Ultimate are effectively pre-formed strips of thermal putty rather than 'pads' as it's usually understood, and if you check out the price of good thermal putty they're very good value (and certainly a lot more convenient and neater than putty).
@SilenceEngaged
Жыл бұрын
It depends on the card, but I changed both thermal pads and thermal paste on my old 3060. Temperatures were through the roof beforehand because of TERRIBLE factory pads and paste from GIGABYTE. I only changed paste on my 3070 because the factory pads from MSI were decent enough at keeping temps low. But the paste was obviously not up to my standard. :)
@qubes8728
Жыл бұрын
I’ve been checking eBay here in Oz for used 3080 and 3080ti’s. At the moment there’s only a couple for sale. One local guy wants the same price for his mined card as a new one. I offered him aud$1000 and got no reply. I’m not sure we will see many mined cards on the market as these guys over invested when the prices were high and can’t come to part with the cards at a realistic second hand price.
@ChrisZukowski88
Жыл бұрын
lol that's their problem not yours. if he doesn't sell now he'll have a hell of a wake up call next week.
@dinobot_maximize
Жыл бұрын
crypto bros are total clowns
@qubes8728
Жыл бұрын
@@ChrisZukowski88 yeah i could care less thats why i offered him 1000. pretty generous for a second hand mining card i thought? He will probably end up keeping it, I would espacially if i paid like 2500 for it lol
@Noiconnotag
Жыл бұрын
I would have added a test of the cheapest non-brand pads as well for comparison.
@StefanEtienneTheVerrgeRep
Жыл бұрын
You don't need thermal pads. You just need Thermal Paste. I took off my pads, and coated a good layer of thermal paste all over the memory, and put another layer over the rest of the gpu. I put some inside the Display Port as well. It lowered my temps down 58-65c. Was incredible. And I still had some left to make a sandwich.
@kaloifortich4491
Жыл бұрын
I highly recommended toothpaste. Doesnt lower the temperature but my card now has that winning confidence and all-day freshness to deal with life's challenges.
@swizzler8053
Жыл бұрын
@@kaloifortich4491 hahahahaha
@kane6193
Жыл бұрын
Hey Bryan, love the videos keep them coming!!!! What thermal paste do you recommend/did you use on the 3080?
@Stray_x
Жыл бұрын
I got my 6600XT *almost* new. The card had only been on the market for a couple months at the time, I think the guy wanted to scalp it but found he couldn't get a crazy offer. Doesn't matter how new your card seems, though. It's always worth checking! Pads like these are cheap enough and are worth the peace of mind they offer. As well as being handy to have in your own personal Tech YES repair kit.
@killerrf
Жыл бұрын
Should have tried or compared the cheaper Amazon thermal pads where you get 4 sizes for $10-$15
@Safetytrousers
Жыл бұрын
Different pads have different thermal conductivity. That's why some go for a premium.
@killerrf
Жыл бұрын
@@Safetytrousers oh yea I get that just see what temps diff would be between regular and “premium” pads.
@Safetytrousers
Жыл бұрын
@@killerrf The original pads on this GPU would have been regular pads. They wouldn't have been designed to be actively bad.
@t0nyxgq
Жыл бұрын
I thermal pad modded my 3080 FE with 2mm Gelid Extreme pads and saw some improvement. Two weeks later, I copper modded with 1.2mm plates ($10) and thermal paste on either side and the improvement was much more significant. I don’t mine and cap my frame rate to 60fps while gaming. I just want my GPU to run cool and last a long time. My next rig will be in at least 5 years.
@99mage99
Жыл бұрын
Imagine having a 3080 and capping your fps at 60
@not-a-w33b
Жыл бұрын
@@99mage99 well if it's 4k monitor, 60fps makes a lot of sense.
@t0nyxgq
Жыл бұрын
@@99mage99 My monitor is a content creation monitor and is at 60hz. More fps caused tearing issues so 60 fps is smooth enough for me.
@99mage99
Жыл бұрын
@@t0nyxgq Imagine having a 3080 and only one monitor.
@t0nyxgq
7 ай бұрын
@@99mage99i have 2 monitors both at 60hz. But recently I got a third 2K monitor at 144hz and it’s very smooth. I use that for gaming now.
@Pacheenee7
Жыл бұрын
Critical thermal pads are the best and are shipped in the exact sizes you need for whatever specific card. Dropped my vram from 105 max to 75 max
@TheGameBench
Жыл бұрын
Even at 64 degrees, that's a long way off throttle temp for the G6X. I've always thought G6X ran really hot, but maybe it's just this cooler is really good or they used better pads? But if you're buying a used 3070 Ti on up... I might not consider it if they haven't done something for the memory since it's really easy to hit throttle temp when mining. I know there are a lot of better options, all the way up to copper shim plates that really help with cooling.
@JadeIsler
Жыл бұрын
you uploaded this while I was replacing my 3090 Suprim X's pads with K5 Pro (thermal pad replacement paste)... wavelengths
@TechGamer-pq1gu
Жыл бұрын
mine went from 95-105C to 70-76C switching from the original pads to these Gelid ones so it's definitely worth it.
@SameAtol
Жыл бұрын
I'm really more curious how the stock ones compare to some really cheap 1 dollar pads, I've used plenty of those, and they always seem to do okay, but I have never properly tested them, I might give it a try on my 3080 since I have quite a few left
@jovanpejic
Жыл бұрын
5:08 I would not change the tape in this condition. And it seems to me that the tape that nVidia uses is much better, so two reasons I wouldn't go into this...
@DimMVK
Жыл бұрын
Thermalright makes good pads also. Used them in variety of components and the results always were great.
@idontwatchtv
Жыл бұрын
It's a must if you have a high TDP Card (GDDR6X) and using it for mining, more of a recommendation for gaming.
@NiyuMiya
Жыл бұрын
I did a research as well back in the day about this like half a year ago... but I wasn't sitting on any High End card, I was using MSI Gaming X RX480 8GB for a quite some time, and I was pretty concerned about the thermal pads after changing my thermal paste, so I looked for something to replace them, just for the sake of getting peace of mind... and I did order the same pads that you did there but different thickness to match the originals. After replacement my Memory Temp was slightly less... and core also dropped few degrees, so it didn't change much, but I think it was worth it anyway... I replaced my RX480 for RX6600 on my Main PC though, but I think I will do the same course of action with pads after some time anyway...
@josephchristianruiz6581
Жыл бұрын
hopefully you could score some Aluminum Nitride Pads and test it out, I've read some articles online that it has the highest w/mk compared to the rest of the thermal pads being sold online
@spookytofu2078
Жыл бұрын
Could you revisit this and add thermal pads on the back so that the backside of the memory contacts the backplate? And see how much difference it makes since gddr6 is flip chip and the hot side is at the back
@ertted1295
Жыл бұрын
if the back plate was not paded its going to be tricky as he will have to figure out the thinkness of the pads i know from seeing miners change pads yes changing the pads on the back plate does help too even on my 3060 that i redid it helped
@kerotomas1
Жыл бұрын
2 ribeye steaks? God dang, it's cheaper to just buy a new card from Amazon then :P
@Macho_Man_Randy_Savage
Жыл бұрын
Gelid makes good stuff, check out their mini fan header to standard fan header adaptors, if you need to run a fan off a GPU PCB for a Hybrid setup so it's all self contained.
@serjturischev9557
2 ай бұрын
Ridicilous. Man buying near top product from respectful company and then should tune it for temps goes down. This some kine of madness for me.
@EliteRock
Жыл бұрын
MSI are easily the most conscientious when it comes to the pads on their cards - try a pad swap on a Gigabyte or EVGA and the difference is much more marked.
@roythunderplump
Жыл бұрын
What case are you using 10:20? Looks Tech Yes Crackalackin
@joshuascholar3220
18 күн бұрын
The RX 6000 series uses cooler GDDR6 not the same hot GDDR6x vram that the consumer cards use.
@jong7258
Жыл бұрын
2 other thing You could test, the Gel pads whit and without finger fat on it, and a copper mod.
@Kizzster
Жыл бұрын
They charge you more than founders edition to only give you crappy pads on them wow
@jonyblizz
Жыл бұрын
I did the same on my 3080 FTW because here in Mexico is a must since I got 100° C on stock pads and 92° C on gelid
@fast_eddie3441
Жыл бұрын
Silver paste! It's been unbeatable for decades and there's a reason for that..
@darrooxx
Жыл бұрын
Where is the intel undervolting video workshop ?? And can you build a gaming rig what consumes less power than normal.
@TLM-Nathan
Жыл бұрын
When measuring your original thermal pads make sure you measure the part that has NOT been compressed because obviously that'll make a difference.
@arfer1470
Жыл бұрын
I think you are right, new pads should be fractionally thicker so that they can compress slightly and spread into imperfections in the surfaces. I believe manufacturers of the materials normally specify this on the datasheet. So a pad measuring 2mm when removed should be replaced by a pad that is say 2.2mm to 2.5mm uncompressed.
@makifrable
Жыл бұрын
Brian, try to have a look at the PTM7950 thermal interface material, because reddit recently started to go nuts about it
@jamesmetz5147
Жыл бұрын
Good Advice. Thanks
@surfx4804
Жыл бұрын
The original pads on your 3080 look good anyhow and you are water cooled?. The FE 3080 had some nasty oily pads, and mem temps would easily hit 100C, especially in mining. That's why most people did the pad swap. For myself and my original FE 3080 swapping the pads made a huge diff to the VRAM (like over 20C). Incidentally GPU temps don't drop and could even go up a little as you are now dumping more heat into the heatsink. You do need to make sure you get the right pad size as it can affect the GPU die mounting pressure. I (and others I know) have had good results with Thermalright pads.
@javvyjavvy
Жыл бұрын
I got my brand new msi 3080 gaming trio 10gb. Came not new, not sealed. Definetly repackaged. I dare not return it though since i won it on a shuffle. After watching a tear down video i notice my cards missing thermal pads all over. Would love to repad and repaste it.
@MIK33EY
Жыл бұрын
Be curious to see the same test done but with the copper shims mod - use copper sheet the same dimensions as the thermal pads with the bare minimum of thermal paste applied between the memory and copper shim and then also between the copper shim and cooler. I’ve seen this done in other vids but been dubious with the results - they seemed to good to be true.
@TheFutureTech
Жыл бұрын
The sea hawk x may also be getting a new VBios with higher limit draw soon too
@thomasijontichy5651
Жыл бұрын
So, forgive me, I'm but a newbie at these things. But you compared a GPU with (possibly) dried out (and certainly not new) thermal paste with the same one with new thermal paste and pads? Is this correct? If that is the case, how do we know the effect of the pads?
@spacebarwasd9782
Жыл бұрын
I assume you changed thermal paste as well... Which one did you use and did it improve? Thanks
@15digitlongname
Жыл бұрын
if you do it to your main gpu,we'd love to see another test to see if this was a one off situation or if it looks to be more or a trend
@markhovscrch4050
7 ай бұрын
Can you help me for the Gelid GP-Ultimate thermal pad thickeness for VRAM, Backplate and those weird row of blacks from my Gigabyte RX 5700XT 8GB OC? the stock pads were dry and not sticky anymore.
@abingeorge4984
Жыл бұрын
For my 5700xt the gelid extreme pads reduced about 10 to 15 C but my core temp rised a little . Expensive, worth it if youre watercooling
@wanderer7779
Жыл бұрын
What temperature are you getting? I was getting about 70c while i was mining with the card which seemed fine to me. Kinda lazy to open the card but the thermal paste is due as well it's been 2 years since i bought it.
@Serious-Man
Жыл бұрын
yeah, like miners will actually disclose the card was used that way and then discount their cards accordingly. Ebay full of high priced used cards that state "never used for mining". How are you supposed to make sure you get a good price?
@ogm19881
Жыл бұрын
Fyi to people out there if you've bought gigabyte graphics cards this is definitely something that should be done as stock thermal pads leak oil and are known to cause issues or loose cooling performance.
@sonowolf
Жыл бұрын
would love to see an updated xeon build and your opinion as if its worth it. cheers!
@MakemeSumMuffins
Жыл бұрын
TechYES you already tried those mini heatsink for CPU VRM. You should look into copper shim/sheets that are on spec with the GPU pad thickness. There are already mods for it and I have it on my 3070Ti. You should give it a go and make a video
@batou1468
Жыл бұрын
I finally got around to changing my 3090fe out a couple days ago. I used the thermalrights (3 pads) 1.5mm and went from 104c to 80c. Can't believe how expensive this card is and had to do this to keep from nuking my system and prevent thermal throttling... Ridiculous... 😮💨
@milanbanjac4649
Жыл бұрын
hey tech city which is better extreme vs ultimate pads wanna buy some and do you know which thickness for rtx2070 super fe and rx5700 xt also a fe model
@EKnee14
Жыл бұрын
I've replaced mine on my 2070 with these, they're great it also looked like my specific card had some missing on a set of vram. I have also heard after a certain point you might have deminishing returns as the backplate cannot dissipate the heat quickly enough. Would recommed 10/10 mine dropped about 10C
@darkfox2401
Жыл бұрын
You also put bigger pads on there for more heat dissipation and transfer
@ngk330
Жыл бұрын
I have a zotac 1070 from 2017, I want to do paste and pads but I have 0 clue how think of thermal pads I need, how do I figure that out?
@LightSoundGate
Жыл бұрын
Had similar problems on the VRMs of my ASUS Strix RX Vega 64. I changed the pads and the temps went down over 30 °C. Some GPUs have this problem.
@genocidehero9687
Жыл бұрын
I have copper heatsinks on my bacck plate from when I was mining. I just placed them on with out opening it up.
@swizzler8053
Жыл бұрын
Stock thermal pads and thermal paste are sheit. I really don't get why company's skip on these important things.
@mrsam1999
Жыл бұрын
How to find out where are the Vrams ? if some thermal pads has been completely demolished ?
@Emanuelman115
Жыл бұрын
I don't think that the test was accurate ... cuz on the first one the thermal paste was dried and on the second one it was fresh. which could be the only reason for the temp change. correct me if I'm wrong
@christophervanzetta
Жыл бұрын
For a top mounted radiator (for exhaust), do you recommend a push or pull configuration? Currently it’s in a push configuration but it’s damn noisy and wish to quiet it down a bit
@nathanlowery1141
Жыл бұрын
This is very dependent on the case you are using/ config of the other fans/radiator placement. Need more info for very accurate advice. In general tho positive pressure in the case is best
@perhapsjames_
Жыл бұрын
I added thermal pads to my Gigabyte 3060Ti backplate. So the backplate actually does something now
@binusworldoftechnology5867
Жыл бұрын
Used peosucts from Gelid. Good price/quality. I still got my Xtreme thermal paste and is easy to appky and works perfect.
@Capybaracomputers
Жыл бұрын
I’ve recently had TDR blue screen of death while using a 3070 does anyone know if replacing the thermal pads will help solve the issue?
@jacqli69
Жыл бұрын
Can you test Gelid Ultimate vs Thermalgrizzly Minus Pad Extreme? Those TG pads are an upgraded version of their old Minus Pad 8, and they are ridiculoudly expensive. I think 3x the price of Gelids. I can't find anyone who's willing to test them. My GPU doesn't have thermal sensors on memories so I can't really do it myself.
@RANDOMNATION907
Жыл бұрын
I've done this with laptops too. I have always used Fujipoly brand thermal pads but, yeah.
@southbronxny5727
Жыл бұрын
Should've added kingpin paste on memory, then place the pad, then add more paste to finish the sandwich will give you better thermal transfer. Also, the gelid pads are too hard, so look for softer pads like Valor Odin.
@EhEhEhEINSTEIN
Жыл бұрын
I replaced my stock ps4 pads with fujipoly ultra extremes and while I haven't measured, it does seem to have helped transfer more heat to the mid-plate. I compensated by cutting some holes and adding some fans. Looks pretty hc but it I like it!
@excdnforces4035
Жыл бұрын
i saw a temp drop with re-pasting the thermal paste on the gpu chip itself
@Safetytrousers
Жыл бұрын
The GPU die does not affect the temperature of the memory (unless the die is throttling). This was a pad test, not a paste test.
@neecross
Жыл бұрын
Bryan you should check out the k5-pro it should give you better performance and there is no concern about the size/height
@gamingpcassemblato432
Жыл бұрын
Review the juicy stake tho!
@ReaperLSX
Жыл бұрын
I used these same thermal pads to replace the Red Devil 5700XT stock thermal pads
@hanp2205
10 ай бұрын
if you use gelid solutions gc extreme thermal paste your gpu temp would have dropped even more
@crckdns
Жыл бұрын
I've got 3 meters roll of that for about 5€ from Ali ...that's cheap and works!
@davo3020
Жыл бұрын
I have 2 asus strix 1080ti's, is it worth changing the memory pads?
@cracklingice
Жыл бұрын
Holy crap I wish I had temps that good. My freakin vram is over 100C. :(
@binomair9326
11 ай бұрын
Hi, What you think if i put thermopad on gpu prossoser not thermopast !!!
@Will-ik4bk
Жыл бұрын
Hope that's the paid version of OCCT. Linus got a lot of crap from the developer and redditors for using the free version in one of his videos.
Пікірлер: 197