Brother,you are a lifesaver the absolute first video to show this,TU
@mariefx6401
10 ай бұрын
All you had to do was drill holes in the kayak to allow the screw to go flush. Open the circular hatchet and install the nylon washers and nuts. Great video overall it helped my husband and I mount his motor. Thank you
@lawrencebarker7529
11 ай бұрын
I got one to and did it different. Drilled through the plate and the hull for more support with bigger washers and sealed it with water proofing.l The long screws are there for that not to cut short ones are for the motor plate.
@FishingTexan
2 жыл бұрын
Thanks for posting! I just picked mine up about a week ago but have yet to install the motor. I like the bracket placement you chose allowing the motor to sit as far back as possible. I'll be using your method with a few tweaks to install mine. Thanks for the help!
@texasjonesfishing1318
2 жыл бұрын
No problem man. I try to use the simplest methods and work with what you got. I appreciate the view. I actually just took the kayak out today in my opinion it did way better than what I expected. The motor was strong and accurate at 22 mph wind gust with a constant 15 mph. Not that fishing was good but I'm very pleased with this setup
@FishingTexan
2 жыл бұрын
@@texasjonesfishing1318 Yeah, I fished yesterday and it wasn’t that great of a day either. Just finished my motor install and it went quick with no issues. Thanks again!
@texasjonesfishing1318
2 жыл бұрын
@@FishingTexan your welcome glad it helped. I finally got mine registered and on the water it did awesome 👌
@ReelHardFishing
2 жыл бұрын
Your bolts should've went all the way through and used lock nuts and rubber washers on bottom. No need to remove factory mount.
@BibleBassTV
Жыл бұрын
Really
@jerryharris5149
2 күн бұрын
I'm having to find shorter screws too!!
@BibleBassTV
Жыл бұрын
What did you do with the metal clips
@magnusob1875
2 жыл бұрын
Do you know how wide of a gap are between the mount holes. I have a 128x and I want to mount a diy mount but I’m not in town currently but I was hoping to make a mount where I’m At currently
@texasjonesfishing1318
2 жыл бұрын
I don't know off the top of my head. But I would be more than happy to measure it for you later when I get home.
@magnusob1875
2 жыл бұрын
@@texasjonesfishing1318 would be much appreciated 🙏🏻
@andrewdohrmann5981
Жыл бұрын
I like this method unless i need to for a sturdier connection I don't want to drill through the hull
@texasjonesfishing1318
Жыл бұрын
Iv seen a few guys make a plate that goes all the way back. After u use it a few times the plastic starts flexing
@the_grumpy_trucker
2 жыл бұрын
The bolts that come with the trolling motor mount are a different thread than the anchor nuts on the kayak!
@flintriverkayaking7051
Жыл бұрын
Need to check out my motorguide xi3 video before you go drilling holes in your kayaks, no drilling needed
@texasjonesfishing1318
Жыл бұрын
I love drilling holes in mine 🤣
@texasjonesfishing1318
Жыл бұрын
Do you have any lights set up on yours Iv been trying to find some different ideas for that.
@flintriverkayaking7051
Жыл бұрын
I have the lights but have not put them on yet, I have lights on my L4 Expedition and you can't drill in that or just really don't suggest doing that I ran the wires under a clear tape called Alien tape it is pretty amazing stuff it's not coming off I actually used it for a keel guard so it has been submerged for days at a time and has not budged or let any moisture in, it is quite amazing, gorilla mounting tape is comparable to it. I'll be watching your stuff to see what you do for lights and if I see anything I think is a good idea I'll send it to ya I've been waiting as well brother.
@texasjonesfishing1318
Жыл бұрын
@@flintriverkayaking7051 he'll yea man I appreciate it. I have pump tape for water wells lol I'm new to yaks so I do what I can to get by lol if I screw it up to bad I guess I'll buy another yak lmao 🤣 jk
@ReelHardFishing
2 жыл бұрын
Bro, you did not have to cut them, I have same kayak. You must've installed washers wrong or something
@texasjonesfishing1318
2 жыл бұрын
I tried it that way it wouldn't work. My buddy had the same problem with his. I would have much rather not cut them lol
@ReelHardFishing
2 жыл бұрын
Trust me, all you needed to do was a dry fit on the mount, then get I think it was 15/64 bit. There is a video on KZitem of where I got the idea from. I'll share the link.
@ReelHardFishing
2 жыл бұрын
kzitem.info/news/bejne/poOHtm2hpouSaKw
@ReelHardFishing
2 жыл бұрын
Perfect tutorial. I didn't video my setup
@beh4852
Жыл бұрын
I just drilled all the way through without taking the plate off. Put washers per instructions. Easy pezi
@stevensuhar8302
3 ай бұрын
Quick release for when you go under on a lake? Seriously, spending money on an Old Town or Hobie allows you to fish more water.
Пікірлер: 30