I've had my D1 Pro sitting there ages to be put together. The instructions with the machine are not that good. I am so glad I found this video it's been so much easier. A lot of stop, start and plenty rewinds. Now all I have to do is get the smoke remover machine up and running then attempt to do some cutting 😊 Thanks again
@ninescordes2901
4 ай бұрын
Thank you. I was waiting my brain to understand the instructions. Got tired of waiting. Your instruction made it come to life.
@QuotidianStupidity
Жыл бұрын
There is a plastic sticker over the air assist screw hole on mine - I assume that was supposed to be removed. Also adding in the coloured connectors is awkward af... and using cable ties is very cheap. this part of the design could definitely use some improvement
@IceTennisLeague
Жыл бұрын
I ABSOLUTELY LOVEEEE THIS MACHINE!! 100/100!! you've made my imagination come true with all the things I can make thank you!!
@multiversity6290
2 ай бұрын
What have you made with it? I have just bought one and love to hear everyones projects
@IceTennisLeague
Ай бұрын
@@multiversity6290 professional business cards out of metal. Even made some For my sponsors who love them
@upstatedoc3287
Жыл бұрын
For some reason my D1 Pro won't engrave a picture, it just slides up and down. No sideway motion
@mutley192
8 ай бұрын
my first set up, when i try to frame the image i press frame and the laser module either goes fully right and the alarm go off or left and hit the side again with the belt makinga horriblre noise as well any ideas whats going run
@proudcanadianeh4663
8 ай бұрын
Thank you so much for the great video! Ive encoutered my first issue, for the step at 8:01, I cant plug the White cable into the white socket, I have tried for ways, it seems there is a plastic piece on the white cable that it stoping it from sliding in, ayone else have this problem?? Thank you!
@kandiecandelaria3134
10 ай бұрын
Just got one, put it together and now what? Have the red one. Can I use the software laser box basic with it? Someone said no but you can use it with the blue machine? How much is laser burn?
@barb8190
7 ай бұрын
Question, my lock screw came out on my laser, I cant seem to get it screwed back in. any ideas
@gknoxis
Жыл бұрын
I assembled my D1 Pro 20 W yesterday. Sliding the two plates to the front plate didn't work, the circuit board has an edge in the way. The air assist won't screw on. The shaft connecting the two sides was a little bent so it wobbles, the bend is ~ 3 mm. I haven't had time to test it. So not sure how the bent shaft is gonna impact the performance.
@EmbraceMaking
Жыл бұрын
You can use the back instead of the front since the PCB is in the way. I put together a pretty extensive video here on setup that covers some things the manual misses plus better wire management: kzitem.info/news/bejne/w6hjza2Do6GojII
@mikocheeks193
6 ай бұрын
is this wifi compatible or do I have to connect it to my computer?
@Cancun771
10 ай бұрын
Ehm that bottle wasn't even close to being centered in the first few shots and then it magically was all of a sudden.
@BrainwavesofHope
6 ай бұрын
Hello I'm at the phase of experimenting materials but I have questions for you before I begin: 1.Do I need both an air assist and a fume extractor? Do they do the same thing? 2.Do you suggest a metal plate or a honeycomb Laser Bed to go on top of silicon mat but under material? 3. Should the laser slide all the way to the mat or be adjusted where when it slides in, the back metal piece of laser underneath plug is even with the bracket its attaching to? Ultimately resulting in laser being approximately a quarter inch from the mat?
@xToollaser
6 ай бұрын
1. Better to have both if you always cut wood 2. Yes, that's gonna help you to have a better airflow 3. Don't quite get it
@BrainwavesofHope
6 ай бұрын
@xToollaser thank you for your time and support. I believe your order # 1 & 2 answers' are to my questions order 2 & 1 correct? Q3 : my laser just slide in the holder slot and is flat to the mat. It slides in and out freely as I choose. Is this a correct position? Is the laser suppose to be a certain height from the mat during assembly or does the height adjust with the command from the software?
@jimcarris3258
Жыл бұрын
someone please help. I cnat find the answer and it should be simple. I added the Risers on my D1 pro 20w. I cant get the laser module to go low enough
@matthewjanovich4552
Жыл бұрын
Remove one set of risers
@AI5HV
Жыл бұрын
Your background music is too loud. Cannot hear the muffled audio as a result.
Пікірлер: 23