would love to see the dynosheet; Good to see that the project is alive, congrats on your hard work
@sumalei
Жыл бұрын
Thanks. Check the other dyno video, at the end you will see dynosheet
@zygisis
Жыл бұрын
Nice hp numbers, nice sound
@emsis1990
7 ай бұрын
Brutal sound 🥰
@futuredinghy
7 ай бұрын
Sounds awesome nice job!
@sumalei
7 ай бұрын
Thanks
@Foscora
4 ай бұрын
Oh good job, not many 10VT doing these kind of numbers!
@BigDankJuicyBlunts
Жыл бұрын
Sick, very inspiring for my build. Are you using the stock audi trigger? I’ve got a lightweight FW, it worked with the CIS so I’m sure it would for vems?
@sumalei
Жыл бұрын
Few years ago I was using auditrigger it worked quite ok with vems, but now im running 60-2 in the rear seal. It should work if there's one reference pin at the back of flywheel
@BigDankJuicyBlunts
Жыл бұрын
Would you recommend going 60-2 rear main from the start? Any tips or special tools for installing it? Thankyou sir
@sumalei
Жыл бұрын
@@BigDankJuicyBlunts yes i would reccomend using 60-2 if you have a chance, since its easier to setup and its more reliable. You dont need any special tools, seal has special adapter to install it
@maler88
Жыл бұрын
Bomb ! 🔥
@zyankali2357
8 ай бұрын
Der Kotflügel Bremst den reifen 😂😂😂❤❤
@dennismerk2229
4 күн бұрын
das tut weh beim zuschauen
@zyankali2357
4 күн бұрын
@@dennismerk2229 weil du nur einen Corsa fährst? Da würde mir auch alles weh tun
@dennismerk2229
4 күн бұрын
@@zyankali2357 ziemlich subjektiv, findest du nicht? und ich fahre uebrigens ein audi 80 1.9tdi
@zyankali2357
4 күн бұрын
@@dennismerk2229 hatte ich auch sehr guter Motor mit VEP . Jetzt 1.8 mit MKB . BAM und ein 2.3 5zyl Audi Avant
@dennismerk2229
4 күн бұрын
@@zyankali2357 poa 2.3 im Avant ist ein traum, 10v Nehm ich an?
@karlesser9541
Жыл бұрын
OMG 😱 Soooo nice!
@PositiveStarMan
Жыл бұрын
Yes sir!!
@petroldrinker88
Жыл бұрын
Nice, now I finishing my audi 90 q 10vt but i think it will be 350hp or somethink like this. What you change to have that power?
@sumalei
Жыл бұрын
Check description below video
@petroldrinker88
Жыл бұрын
@@sumalei Why you change valve springs? In catalog catcams this camshaft can work with OEM springs.
@sumalei
Жыл бұрын
@@petroldrinker88i changed valve springs because i had valve float under boost, i couldnt even reach 6500rpm
@wojciechszymanski998
8 ай бұрын
Hi , I have the same engine and my goal is 300-400 HP . Can You tell me what upgrades I have to do ??
@sumalei
8 ай бұрын
Hi, i can tell you, do you have messenger?
@thomastournier4521
10 ай бұрын
Waouw impressionnant pour un 10v moteur KG ? Quel est la configuration des pieces moteurs pour cette puissance ?
@sumalei
10 ай бұрын
MC engine, check description there are some specs
@Wolfy_11234
5 ай бұрын
Stock internals?
@Torsen55
Жыл бұрын
Колеса арки не протирают?
@damianolczyk3496
Жыл бұрын
Great car. Standard cluch?
@sumalei
Жыл бұрын
Thanks. 6 pad ceramic clutch disk + 20VT 3B pressure plate
@aleksej8034
Жыл бұрын
Nice Audi!🔥🔥🔥Stock Camshaft?
@sumalei
Жыл бұрын
Thanks. Not stock, Catcams 282/276 cam
@aleksej8034
Жыл бұрын
Boost?and fuel E98?
@sumalei
Жыл бұрын
@@aleksej8034 2.4 bar with E85. Check description
@aleksej8034
Жыл бұрын
Sorry,dont see😅Just i have MC block,and NF head 2.0bar boost,and 500hp 550nm E98.7000rpm.HX40.Just interesting yours specs.Thanks you.
@sumalei
Жыл бұрын
@@aleksej8034good numbers. Im also using same setup, MC bottom with NF head. We could have made more power but alternator started to drop voltage at higher rpm, and dwell timing was extending and started to missfire. I fixed this issue now, so next plant is to make 600 hp 💪
@karlesser9541
Жыл бұрын
what kind of budget do you think I need to make this performance?
@sumalei
Жыл бұрын
Its really hard to tell, depends on location that you live. Personally I think I have 3-4k euros under the hood now roughly
@vitkovic57
Жыл бұрын
@@sumalei hi, where did you get the work done? And i've been told that the 20v block can handle sputter bearings while the 10v cannot. You had no issue with this?
@sumalei
Жыл бұрын
@@vitkovic57hi, I did everything myself. Sputter bearings is just technology of coating, so I can't see why it wouldn't work between these two engines. I'm using King Racing bearings, I haven't had problem with that
@karlesser9541
Жыл бұрын
@@sumalei can i write you an email? I still have questions about the conversion, my 10v should also get the power.
@sumalei
Жыл бұрын
@@karlesser9541of course
@TaZzeuR18
10 ай бұрын
salut comment tu a fais pour connecter ton ecu sen capteur pmh
@sumalei
10 ай бұрын
English?
@TaZzeuR18
10 ай бұрын
Hi, how did you connect the pmh on the hall effect to you a diagram of the connection you made? How much power did you get with the 440cc injectors?
@sumalei
10 ай бұрын
@@TaZzeuR18 hi, what is pmh? 440cc injectors maxes out at about 300hp with 95 fuel, and even less hp with ethanol
Пікірлер: 72