TYVM! Used your guide to get to the stalks on an LHD car--same exact procdure :) Very well explained but one thing I'd mention for others that you seem to have edited out... Getting the bottom cowl off of the column. You can't take it off right away as the lever that unlocks the tilt/telescoping won't allow it. Tried for a while seeing if you could twist/tilt/rotate the cover to get around the lever but no dice. However you just need to remove the two screws holding the plastic handle to the lever and remove the handle. Thereafter the bottom cover can slide right off the remaining metal lever, and then it's out of your way as shown at the @4:08 mark.
@kthornicroft
3 жыл бұрын
Top job. I got to the indicator/cruise control stalk and freed the outside tab, but didn't want to pull too hard and scrap something. Looks like it's all in the wiggle! Giving it a go now. Ta very much!
@phoebegolder4123
2 ай бұрын
Great step by step helpful video. Thanks so much
@jerichotm2122
3 жыл бұрын
That was unbelievable well explained! Thanks! It is tricky, though...
@mdeyab
Жыл бұрын
Thanks are due. Used your video to replace my blinker stalk. You saved me a couple of hundred dollars. After I finished I got a "steering wheel" and "traction control" amber warnings. They went away once I started driving. It gave me a fright. So, everybody, don't panic if this happens. Just drive it forward a bit and the warnings will go away.
@ourjems
Жыл бұрын
Excellent saved me a small fortune only down side with my Audi was the air bag light stayed on had to use obd reader
@blackhawk0606
Жыл бұрын
Thanks to your video I have done it 2 weeks ago. FI the small wire at 4:33 could be replaced with an allen key n°2.
@ockhamknife4774
2 жыл бұрын
Thank you so much.Your video has been a great help to me, thanks again for a job well done.
@kokokanev3025
5 ай бұрын
Благодаря ви с това видео ми спестихте пари
@josecatalan6085
Жыл бұрын
This is a great video with excellent explanation on how to remove everything, do you have a tutorial on how to replace the ignition lock cylinder?
@markfarrier1711
6 ай бұрын
Hi there just bought 59 plate 1.9 tdi e newer shape and washer jets aint working either is rear wiper (fronts are working) but rear wiper working when selecting reverse changed washer motor checked all fuses code 00888 wiper switch faulty do you think replacement wiper stork would fix thanks
@ramoncassemiro9655
Жыл бұрын
Thank you for you job, Very good
@3XT4SY6
8 ай бұрын
I have recently problem on my Audi A3 8p 2010, the airbag icon on dashboard appeared, when I did the diagnostic it says - Driver airbag ignition squib 2 has short circuit to ground ( Intermittent) Does anyone know the location of this driver airbag squib 2 ?
@nick798
11 ай бұрын
Thank you for a great video I was able to follow it to change the stalk trying to find my non working wiper problem. So far I have changed fuse. Changed wiper motor and wiper stalk. Still no wipers any more ideas?? There are no faults displaying on dash. Rear works fine front jets work but arms won't function.
@SelectVehicleSpares
11 ай бұрын
I would check that there is power at the wiper motor connector/plug, and work back from there. Also check that the bonnet lock sensor is working correctly, it requires to be in the closed position before the front wipers will work.
@JoeyCbr
2 жыл бұрын
Great instruction
@SelectVehicleSpares
2 жыл бұрын
Thank you!
@TheJimbobjimmy
2 жыл бұрын
I have just bought an 8p where the main beam won’t work. It won’t flash and when I put the main beam on with the head lights it will come on but won’t turn off. Thinking of changing the indicator stalk but wondering if someone has been in there before and fit the wrong one? Maybe that why it’s not working? The top cowling doesn’t sit right so I know someone’s been in there before. how do I know what stalk I need please?
@SelectVehicleSpares
2 жыл бұрын
Hi, if you message us with your vehicle chassis number, we can tell you the correct part number for the indicator stalk on your vehicle.
@TheJimbobjimmy
2 жыл бұрын
@@SelectVehicleSpares amazing thank you. I have messaged you on eBay. Fb link isn’t working.
@blackhawk0606
2 жыл бұрын
Great tutorial ! Do you know the torque to apply on the M12 to tignten the steering wheel?
@SelectVehicleSpares
2 жыл бұрын
According to the workshop manual it is: 50NM / 37.5 ft-lbs.
@oscarhetakmusic
5 ай бұрын
Why my car doesn’t have that part? 6:29
@joelnedd3720
Жыл бұрын
How do I start to remove the first 2 clips if the steering wheel is locked in place?
@SelectVehicleSpares
Жыл бұрын
You could try removing the steering column shroud (around 3:02 onwards), to see if this gives better access to the rear of the steering wheel.
@SpiralSniperz
Жыл бұрын
I’ve done this, however, now my indicators and wipers won’t work
Пікірлер: 27