i learned something here today, thanks man , have same car 2008 fsi engine thou
@ScarzCarz
4 жыл бұрын
glad i could help. thank you for coming. i need it to break so i can do real work to it instead of this small stuff. i plan on more, maybe some preventative stuff.
@kevingoodman7887
3 жыл бұрын
I see your engine start button is broken, mine did the same, I replaced with the 2009 model year, it has the round start button, good upgrade to do!
@ScarzCarz
3 жыл бұрын
thank you for viewing. yes, my button is broken. lol. according to service records if i replace it, it would be its third. you gave me a good idea about the upgrade. ill look into it, good for content
@septicflamezz775
Жыл бұрын
You just earned a new subscriber🎉 i just got a 2007 Audi A6 3.0 TDI V6 & i was wondering how to swap that bulb out
@ScarzCarz
Жыл бұрын
Thank you so much, I appreciate everyone. I have a couple more dropping for it soon.
@ragnarfpv5434
5 ай бұрын
Mine doesn't want to work. They are on in the mmi . But on dashboard it says that the left one doesn't work...well, both doesn't. And I changed them too after that, and still nothing.
@ScarzCarz
5 ай бұрын
Thank you for viewing and commenting. There could be several reasons they don't work. Check fuses, make sure bulbs and carrier are seated properly. There are wires within the housing that can become brittle and break away from housing. There are other things to go through but hard for me to diagnose without actually touching vehicle. Like checking that there's power going to the bulb's. I wish I could be more helpful.
@ragnarfpv5434
5 ай бұрын
@@ScarzCarz thx for the fast reply. I couldn't see any broken wires. But I'll check tomorrow if there is any voltage to the bulb . Thx again.
@anthonysmith993
4 жыл бұрын
We want more videos bro!!!
@ScarzCarz
4 жыл бұрын
thanx man. i plan on more.
@dcswings
4 жыл бұрын
yes bro more videos
@spencersandman6728
7 ай бұрын
On my c6, thé small bulb in the top corner of the reflector has gone. Can’t get it out, all the turning and pulling in the world and it won’t slide out, my arm and hand is in tatters.
@ScarzCarz
7 ай бұрын
Thank you for viewing and commenting. Sorry for your pain. It should just be a half turn and an audible click, try using angled needle nose to save yourself from more pain and aggravation
@pupsikislincis5343
3 жыл бұрын
How did you pulled the it out my small hand can’t fit, and do you twist it Or just pulling it out 2:55
@ScarzCarz
3 жыл бұрын
thank you for viewing, sorry for late reply. it would be a twist to the left for removal.
@GloryHoleBased
2 жыл бұрын
Holy FUCK that took me a lot longer because i didnt know this lol thanks
@Dr.Bigglesworth
2 жыл бұрын
It was miserable for me to get mine out. I have no idea how he did it so easily. I had to use soft jawed pliers to turn it as well as push on the tab to help it. I finally got it out. But, after getting it out, the plastic insulation on the wires literally fell off both wires! I now have to pull the pins from the connector, and put heatshrink over the now bare wires before I reinstall things. I will check the other wires in the lamp housing before reassembly to see if any others are damaged. Kind of poor that these wires weren't rated better to not have the insulation crumble off.
@Dr.Bigglesworth
2 жыл бұрын
It was physically impossible to get the bulb holder back in, and turn it with my hand(s). There just was no room to get my hand deep enoug in there, no matter what angle I tried, or how contorted I got to try to get in there. As a note, all the insulation just fell off the DRL wires. I removed the connectors from the connector housing, and put heat shrink tubing on the wires, and plugged them back into the housing. I made a wooden "tool" with cross cuts (like an "X") that allowed me to slip it over the large "T" shaped tab on the bulb holder, and gave me extra distance to get the bulb and bulb holder back in, and the torque to turn it. I am very surprised at how difficult this is for a simple bulb, and how bad the choice of wire was (clearly insufficient heat specification for the insulation). I wonder if you can buy new headlight wiring. Anyway, thanks for the video!
@EBproperties
9 ай бұрын
@@Dr.Bigglesworth I had the same problem. nearly impossible to get back in, and the insulation fell off. thanks for the tip on heatshrink. I used a large universal socket to reinstall worked amazingly well
@TheRPrs
2 жыл бұрын
Hey. Should i turn day light before moving it out? I reached it but can't move ot out
@ScarzCarz
2 жыл бұрын
thank you for the view. keep all lights off when working on them. cant say why you cant remove yours, they can seem tight if theyve never been removed before. but if the question is if you should turn it then yes, twist to the left to remove
@los9578
3 жыл бұрын
I can’t take mine off
@ScarzCarz
3 жыл бұрын
thank you for viewing. are you turning it to the left.
Пікірлер: 24