Hi can you tell did you have a single power plug for each drive or did you daisy chain them? And if I run 4 power leads from each drive can I just plug them into an extension lead and into the wall without any issues? Thanks. ❤
@ji3200
4 ай бұрын
Is your sevo motor 110V? If yes, is your white controller 15amp or 30amp?
@gomini3707
4 ай бұрын
Hello, nice rig! Can I ask what cabinet are you using to house the servo drivers ? This one seems neat.
@Wachito78
5 ай бұрын
Are you on a second, floor level? if so, how is the vibrations, noise to other rooms in the house? did you reinforce the floor?
@DJ_Racing27
7 ай бұрын
The case that the Thanos controllers are in, is that something that the company offers or did you make that?
@evanphotography5149
8 ай бұрын
Hi, is there any cogging, jittering, when using this motion rig for flight sim when doing a small bank and roll movements ? Thanks
@mercenarysaw
Жыл бұрын
Did you try to run both the v3 seat mover and the e labs mega plus at the same time? I have the seat mover and wondering if the seat mover combined with the e labs is a good combo for the g force feeling. Thanks for the video.
@pwsmanowar
Жыл бұрын
I tried this setup when I first got the RS Mega+. I used the V3 for surge effects with the seatbelt mod. It wasn't worth it though. The effects were redundant, and there is too much flex in the seat when braking because of the way the V3 is setup with the tie rods. It also added substantial weight to the rear of the rig.
@elmalloc
9 ай бұрын
what is that box for, do I need one?
@GUN69_
Жыл бұрын
hey Ralph, I have a question to you. This driver box you have - was that part of the eracing labs kit or is this something you got it yourself elsewhere? Also what is the size of that box?
@pwsmanowar
Жыл бұрын
Hi. It's not part of the kit. www.amazon.com/gp/aw/d/B07NPG9Z5P?psc=1&ref=ppx_pop_mob_b_asin_title
@GUN69_
Жыл бұрын
@@pwsmanowar thanks for the reply and the link
@astellaway
Жыл бұрын
How did you mount the drives into the rack? What kind of mounts or parts did you need for that?
@PvtHaskins1
Жыл бұрын
Yep same equipment. I also have the Accuforce V2. But your pedals are different and probably better than the Fanatec V3
@pwsmanowar
Жыл бұрын
I since upgraded to a Simucube wheel base and Heusinkveld Ultimate pedals. I'm selling my Accuforce and Meca Cup1 pedal set if you know anyone who's interested.
@PvtHaskins1
Жыл бұрын
@@pwsmanowar I would put it up on the iracing forums in the buy sell. I see that stuff go pretty quick if the price is right.
@pwsmanowar
Жыл бұрын
@@PvtHaskins1 I know. I've been lazy about it. Thx!
@mercenarysaw
Жыл бұрын
Did you put fans in the box holding the drivers? Putting mine together 🏁
@pwsmanowar
Жыл бұрын
Nope. They don't heat up.
@pwsmanowar
Жыл бұрын
Are the motors mounted to the actuators, or do you have to do that?
@mercenarysaw
Жыл бұрын
@@pwsmanowar still have to do that 👍🏻
@pwsmanowar
Жыл бұрын
@@mercenarysaw Ok. Mind that gap when you squeeze the interlocking coupler together. That was the only very minor problem that I had when setting them up. I had one too close and it was squeaking.
@rickylah69
Жыл бұрын
is there any space inside the driver cabinet to squeeze in the buttkicker amp? i planning to put the 4 drivers, and my buttkicker amp inside. still looking around for a nice 6u cabinet.
@pwsmanowar
Жыл бұрын
There might be room for one BK amp, but the BK amp has no way of mounting. You would have to slide it in without securing it. I don't think it would be a big deal if you actually did that though. It would be inconvenient to access . I sometimes change the volume on my BK amps depending on the game/car/track.
Пікірлер: 24