Looking sweet, that's how you fit a boot floor, well done lads, this will help people out there to do it right 👍👍
@BMCWorkshop
3 жыл бұрын
Thanks Tony. The fit is great, the jig caused some alignment issues but once the panel is slid in if you spin the car upright again it all lines up lol
@chrismarshall7220
3 жыл бұрын
Keep up the good inspirational work !
@BMCWorkshop
3 жыл бұрын
Thanks Chris, much appreciated
@jamesbarrie2965
3 жыл бұрын
Top work as always guys👍
@BMCWorkshop
3 жыл бұрын
Cheers Jim
@trickster8912
3 жыл бұрын
Nice work there Sean its really coming together now looking good
@BMCWorkshop
3 жыл бұрын
Thanks Ricky, hope your well buddy 👍
@trickster8912
3 жыл бұрын
@@BMCWorkshop been out of action for a while nothing serious on the mend now looking forward to gettin back on the mini keep up the good work
@BMCWorkshop
3 жыл бұрын
@@trickster8912 Sorry to hear that Ricky, hope you feel better soon buddy
@EnginesRob
3 жыл бұрын
Sean - really coming along now. The fit of that heritage floor looks good, without much need for fettling. Thanks for sharing!
@BMCWorkshop
3 жыл бұрын
Cheers Rob, yes the floor was a superb fit and I was shocked that it fitted on the first attempt. Heritage however could have deburred some of the rough spot welds up. They obviously don't really give a toss at what they pump out these days
@Dancing_Alone_wRentals
3 жыл бұрын
Very very very cool. Great video
@BMCWorkshop
3 жыл бұрын
Thanks buddy
@ClassicCarCave
3 жыл бұрын
Sean, Kev, Great to see the boot floor pan go in and be such a good fit can‘t be too many panels left to finsh now! Cheers Dave
@BMCWorkshop
3 жыл бұрын
Cheers Dave, the pan just fell in first time. We did have to spin the car on the rotisserie to allow the shell to relax. The last of the large panels to fit are the quarters and wheel tubs. Hopefully I'll have the tin work finished soon
@simonmercer9530
3 жыл бұрын
Nice job mate 👍🏼
@BMCWorkshop
3 жыл бұрын
Thanks Simon
@deangaryjames
3 жыл бұрын
That shell must be stiffening up nicely now with these panels in? Great job boys
@BMCWorkshop
3 жыл бұрын
Thanks buddy, it's a hell of a lot stronger now compared to when we started the project. Hoping to have all the panel work complete by the end of the year, if not sooner!
@cabdriveruk
3 жыл бұрын
Great video Sean. Looking good now and everything is fitting together nicely. Look forward to more great vids ! Cheers, Jeff.
@BMCWorkshop
3 жыл бұрын
Thanks Jeff, it's really starting to look like a car again!
@jasonkane7747
6 ай бұрын
hi guys, nice to see someone else from scotland on here
@BMCWorkshop
6 ай бұрын
Cheers mate 👍
@LoneStarMini
3 жыл бұрын
You gents are awesome.. When fitting your boot floor to both lower bench flange and top of heel board, how tight were the seams? I get a wonderful seam between bench and boot, but the seam between heelboard and boot floor is being a bear..
@BMCWorkshop
3 жыл бұрын
Thanks Randy, what you may need to do is slightly jack up the floor so that it is level then tweak the seat base until the fit is nice. Long clamps and screws will help hold the seat base to the edge of the heelboard then you plug weld it in or if you have long arms you can spot weld it in
@petermarshall5932
3 жыл бұрын
Sean. Thought you put 2 separate floors in Angus before. Did you start again?
@BMCWorkshop
3 жыл бұрын
Your correct Peter. I installed 2 half floor pans. The boot floor panel is one piece. Had a full mk3 floor pan been available at the time I would have fitted this in one piece too.
@normanraeburn8047
3 жыл бұрын
Hi Sean, You must feel you are really getting somewhere now, you must be nearly finished welding. It’s looking good and the boot floor is fitting well. Have you a colour in mind for the car or is it going to be a surprise. If you can get another few hours on it you will be on the home straight. All the best to you and Kev, Norman
@BMCWorkshop
3 жыл бұрын
Cheers Norman for your kind comments. I'm almost on the home straight with Angus. I just have the 2 quarter panels and rear wheel tubs to weld then thats it. Oh I have a repair panel to do on the passenger side door frame as its rotten on the bottom. All the best, Sean
Пікірлер: 30