great information my brother, my next task is Testing and commissioning of a SF6 Auto Recloser .
@GauravJ
6 ай бұрын
All the best 👍🏻
@carafaadaxmed9067
3 ай бұрын
Helpful ❤
@GauravJ
3 ай бұрын
Glad it helped
@Gazr965
6 ай бұрын
A clever design, it saves a lot of hassle, but also defaults to stay open after 3 failed clearing attempts. Gaz UK
@11masihurc
5 ай бұрын
Generally you don't need to actually "send" people at the location of the transient fault the circuit breaker installed in the Power Sub Station does the job of breaking the feeder and PSS operator recloses it
@mainzahambayi3421
5 ай бұрын
Helpful
@GauravJ
5 ай бұрын
Glad it helped
@ElangovanKP
6 ай бұрын
Great. Thank you so much.
@GauravJ
6 ай бұрын
Glad it was helpful!
@henrychileshe9479
6 ай бұрын
Another banger..!😭🙌🏻🔥
@GauravJ
6 ай бұрын
Do share 😇
@vimalsaravanan-v8r
6 ай бұрын
Hi sir ,, give video about bus bar scheme type detailed
@MirzaAtaullahBaig-w2p
5 ай бұрын
How auto recloser sense the fault current
@krishVeda-Nsh
6 ай бұрын
Excellent...
@GauravJ
5 ай бұрын
Thanks a lot
@sulfikarpa5098
6 ай бұрын
is this recloser and Air break switch same?
@GauravJ
6 ай бұрын
No. They are different. Air break switch do not have capabilities to break the fault current
@Charmingbanana696
6 ай бұрын
can we say circuit breaker is the recloser
@GauravJ
6 ай бұрын
Circuit breaker on its own cannot perform the reclosing operations. It needs a system for that
@Charmingbanana696
6 ай бұрын
@@GauravJ system in the sense one command from SCADA which operates our Circuit breaker in its open close sequence. is it right?
@GauravJ
6 ай бұрын
@Charmingbanana696 for circuit breakers generally an auto reclosing relay is provided. Which gives commands to the breaker.
@DhilipKumar-tf7me
6 ай бұрын
Helpful
@GauravJ
6 ай бұрын
Glad you think so!
@SyarifDayat-jb6zm
19 күн бұрын
I loved your video. I watched carefully and continue to like and subscribed😊
@AEIdgah
2 ай бұрын
Helpful
@manmeetsingh4411
6 ай бұрын
Helpful
@GauravJ
6 ай бұрын
Glad you think so!
@aiasolarsolution3646
3 ай бұрын
In Saudi arbic we work on this project now a day
@fakkirgoudaningangoudra966
Ай бұрын
Helpful
@koustavdas2
6 ай бұрын
Appreciate your work sir...if possible please make a video on bus differential protection scheme with micom p40 relay
@GauravJ
6 ай бұрын
Will try!!
@kajalbhoyar6408
6 ай бұрын
Bagan
@Energized_Human
6 ай бұрын
Learning new🙏😌
@GauravJ
6 ай бұрын
Good to know!! Keep learning
@legendlucifer2755
6 ай бұрын
Helpful
@aviator3888
2 ай бұрын
Presently, UPPCL uses Auto recloser in 220kv and above transmission lines. It's contrary to what you said that autorecloser is used only in distribution network. Plz clarify
@GauravJ
Ай бұрын
Hello. Yes Autoreclosing is done in all voltage level. In HV the autoreclosing is done using the circuit breaker. This is a dedicated device used in the distribution.
@srikant8975
6 ай бұрын
Great!! 🎉 Nice to know about you are the Ex-Siemens employee .
@GauravJ
6 ай бұрын
Thanks! 😃
@Navi_Habakkuk
6 ай бұрын
Thanks, very informative and helpful
@GauravJ
6 ай бұрын
Glad it was helpful!
@Krishnakumar-2223
6 ай бұрын
Sir put pratial discharge videos
@GauravJ
6 ай бұрын
Sure. Will try!
@jeanclaude7320
5 ай бұрын
helpful!! Thanks you
@GauravJ
5 ай бұрын
Glad it helped!
@sachinraj9732
6 ай бұрын
Kindly share your knowledge in Master Trip Relay, Auto Reclose Relay... How they will act in a high voltagr system
@vimalsaravanan-v8r
6 ай бұрын
hi sir, give detailed video about bus bar scheme type , function etc..
@noelfaithfulkari2857
6 ай бұрын
Thanks alot sir.
@GauravJ
6 ай бұрын
Most welcome
@محمدالاغبري-ي9و
2 ай бұрын
Thank you, very helpful
@amitkumarmaurya8521
6 ай бұрын
Kripya Hindi me bhi Explain kare sir please
@DhineshJohnson
4 ай бұрын
Helpful a lot
@JayantaJoyGhosh
6 ай бұрын
Sir, I worked in a 765/400kV Substation in PowerGrid. Where i saw AR in CB and working in different manner in operating sequence. O.3sCO3minCO When there was a fault, Relay initiates ,trip initiates and at the same time Auto Reclose Initiates. CB Trips in about 30ms, then CB will remain open for some time (0.3 sec) to complete the Arc Quenching which is called as Dead Time and is indicated by 0.3S in the Duty Cycle.After 0.3 sec, if AR is in Service, a Reclose will be attempted, and if the fault persists, CB Trips immediately ( AR Unsuccessful ) which is indicated by “CO” in the duty cycle.If its a Single Shot Auto-reclose, the Breaker will go into Auto Reclose Lockout, that means , the AutoReclose Relay will not give any further Reclose Command to the Breaker.After CO, there is a Reclaim Time of 3 Minutes, in which the CB gets ready for Closing, which includes CB Spring Charging Time, indicated by 3 Min in the Duty Cycle. My Question is in your Time Sequence ,How will CB get Time for charge the Spring Because minimum spring charge time is 7-10sec.
@GauravJ
6 ай бұрын
Breaker is always ready to perform a CO operation.. meaning that the spring will be already charged.. closing spring operation also charges the tripping spring
@xheri5710
6 ай бұрын
Automatic circuit reclosers are very significant in reliability of network grid.
Пікірлер: 57