@@jtjjbannie plastic, leather brass all work and won't damage or distort a part
@AleksandrIvak
Жыл бұрын
А если машина не заводится?
@shakibahmad2295
Жыл бұрын
Yeah his wood hammer used 😊😊
@Maniacguy2777
Жыл бұрын
Son: Mom what's there special tonight to eat? Mom: crank shaft with lubricant oil hammered with barring wheel.
@haeschen4026
Жыл бұрын
Underrated comment
@jacobarreguin6324
Жыл бұрын
Jajajaj 😂😂
@bradIeyscarreviews
Жыл бұрын
Not funny
@eazyspace349
Жыл бұрын
😂😂😂😂
@Steezy_Mx
Жыл бұрын
Bearing*
@jchoong4965
Жыл бұрын
When installing bearing on shaft, hit/contact the bearing inner ring. Not the outer ring or it will damage the bearing, specially when it's a tight tolerance fit.
@franksoko8522
11 ай бұрын
Yes sir. Absolutely.
@megadooom340
11 ай бұрын
Nie ucz ojca dzieci robić 🤣🤣 on to lubi robić więc wali w łożysko żeby niedługo rozebrać ponownie 👍
@vex123
10 ай бұрын
I think that cylindrical tool is cut out to avoid this, but not sure.
@ThaneshwarDewangan-us4us
10 ай бұрын
@ReboxTracks
10 ай бұрын
It's made in china 😂
@user-pt1kp4pk8h
Жыл бұрын
Для тех кому интересно - это планетарноцевочный редуктор… очень эффективная штука при понижении числа оборотов до больших значений в малом корпусе. Минус в сложности изготовлении и частых заклиниваниях…
@samuelmartin2817
Жыл бұрын
Thanks I was wondering 😊
@frendofkromanions
Жыл бұрын
Если не запомнить последовательность , то его очень долго собирать.
@Stanislavskiy1985
Жыл бұрын
А где он применяется, Вадим? Скажи пожалуйста.
@Demonius1976
Жыл бұрын
@@Stanislavskiy1985 в самокатах.Мотор-колесо кароче.
@Stanislavskiy1985
Жыл бұрын
@@Demonius1976 🤝👍
@HeyImJoel
Жыл бұрын
- How much grease should I use? - Yes.
@NarutoUzumaki-Nam
Жыл бұрын
He didn't even use enough
@PatrickSwayzeOnDbol
Жыл бұрын
it seemed to be just the right amount...
@mrtango4034
Жыл бұрын
Хаха
@Wtfinc
Жыл бұрын
More, he skimped like a skimper. Should’ve covered the last cog. I forgot what the parts to a harmonic drive are. Wonder what this one is for
@briansmith8967
Жыл бұрын
How much you got?
@Lukas-cr9uj
Жыл бұрын
Вся красота видео оборвалась с ударами молотка по наружной обойме подшипника
@hihirururara
Жыл бұрын
И прокладку еще криво подожил
@ajitchavda5851
Жыл бұрын
😅😮😮@@hihirururara 😅😅😮😂😂
@charlesprvt778
Жыл бұрын
😂😢
@zezitopais965
Жыл бұрын
😂😂😂 é verdade!
@anatoliyrotskin5088
Жыл бұрын
Что ещё ожидать от кетайской сборки
@user-pr3mj9nv1n
Жыл бұрын
Так хорошо все начиналось! Но осаживания подшипника убил😂
@vasyawarszawa
Жыл бұрын
С языка снял
@St-iq1rn
Жыл бұрын
+
@wellways500
11 ай бұрын
Ты чо не слышишь китайскую музыку? Вместо тысячи слов😅
@user-gr5wv5hg6d
11 ай бұрын
Китайская сборка😂😂😂😂
@ortizkz
10 ай бұрын
Там ещё шплинт не поставил
@dolgov123
Жыл бұрын
Подшипник, молотком?!?! Удачи!!!!
@dkmcdk724
Жыл бұрын
В Китае похоже это норма, в прочем и в России тоже.
@BrotherCreamy
Жыл бұрын
Bro made all of Russia angry with this post.
@properlo
11 ай бұрын
А что с ним будет то? Особенно если по внутренней обойме не сильно бить...
@stevothegreat
Жыл бұрын
Not with a metal hammer beating on a bearing , no wonder my transmission had to be overhaul this past summer !
@user-rn7rf8ww1c
Жыл бұрын
а шпильки где?зафиксировано?га
@BastardX13
Жыл бұрын
Thought the same.
@saxonhammer7239
Жыл бұрын
And never hit the out race to seat a bearing!
@MrRoseandrc
Жыл бұрын
No wonder
@jackjfjfjf
Жыл бұрын
Didn't pack the bearing either.
@slippinslidewayz
Жыл бұрын
I could go for a slice of lemon meringue pie right about now.
@Snyper1188
Жыл бұрын
Shit, you ain't kidding, was just thinking about one yesterday.
@metime-kw4tx
Жыл бұрын
Thats the levelof that lubricant. Just one use
@FC0BCA7E7A
Жыл бұрын
I’m actually eating some lemon meringue pie while watching this!
@RErnie-gv1hv
Жыл бұрын
My wife is going to make two Key Lime pies tomorrow. Stop by.
@brianlopez8196
Жыл бұрын
Ye ye
@GunsFreedom
Жыл бұрын
I guess he lost his rubber hammer... never tap in a bearing with a steel hammer.
@iHelpSolveIt
Жыл бұрын
Yeah i know, instant claim😂😂😂 warranty better be good on this. Its going to have scarring
@bennyrich7361
Жыл бұрын
Still no excuse... Use the wood tip of your hammer handle...
@StrokeMyLovePump
Жыл бұрын
Dead Blow Hammer.
@ETsBees
Жыл бұрын
Guess what! It works and last just as long too
@tedbear6012
Жыл бұрын
Not usa clearly
@loftsatsympaticodotc
11 ай бұрын
Small taps may not he too bad. It's all a case of knowing metal and hardness and what impact will deform. You CAN use a chisel as a screwdriver and visa versa; depends on circumstances!!! PS. I own over a 100 ! .... and respect the difference!
@Cheepchipsable
11 ай бұрын
Hey, it's the internet - everything is absolute!
@johneubanks5951
Жыл бұрын
Steel hammer and bearings usually don't mix unless destroying them..a rubber mallet would work a touch better I would guess..
@CheddarCheeseBandit
Жыл бұрын
Leather mallet
@JRCinKY
Жыл бұрын
Use a block of Wood
@EmmetPhD
Жыл бұрын
and never hit the outer ring!
@Cheepchipsable
11 ай бұрын
I don't think the few soft taps he gave the bearings would hurt them, though he could have greased the bearings before inserting them. Sure they will get grease eventually, but there can be some significant wear if they run dry under load for any period of time. The majority of wear to your engine bearings occurs in the first 30 seconds of starting your car in the morning.
@PRND21
Жыл бұрын
Wow, changing the blinker fluid is way more complicated than I thought! 😂
@thechumpsbeendumped.7797
Жыл бұрын
That’s because it’s for a BMW. That’s why drivers don’t want to wear them out by using them.
@wisconsincrhunter5614
Жыл бұрын
Haha
@DevinBoynton
Жыл бұрын
I feel like im getting a tableside presentation at a mechanics restaurant
@arthomer6535
Жыл бұрын
Looked like you forgot to put the key in. Light hammer taps don’t looked that bad.
@cholly853
Жыл бұрын
Never tap on the center race of a bearing. You'll cause flat places on it and the it will wear out faster.
@quartusbuys6831
Жыл бұрын
If the press fit is on the inner, you tap on the inner, if on the outer, tap on the outer otherwise the balls leave dimples on the running surface and you start with a stuffed bearing.
@noreply5829
Жыл бұрын
That is 100% wrong. First, the guy above me explained it well, and second these are hardened and wont take any damage from light tapping. The worst that could happen is that if you tap too hard the ring could shatter in thousands of pieces - but definetly not with the tapping shown in the vid
@morenoredpill1817
Жыл бұрын
sim, foi muito errado ele bater com um martelo de metal isso vai arranhar e danificar a peça, tem que bater com um martelo de madeira revertido de couro ou emborrachado, martelo de borracha nunca vai arranhar as peças.
@thybigballs
Жыл бұрын
You dont know what the hell you're talking about.
@BrotherCreamy
Жыл бұрын
@@noreply5829The balls are harder than the race. They leave indents. Try it yourself.
@edwynn4060
Жыл бұрын
Did I miss you putting in the key in the"keyway"?
@thechumpsbeendumped.7797
Жыл бұрын
I thought that too. It doesn’t look like he put one in and I can’t see an edit where it was done.
@cahauhanm511
Жыл бұрын
Yes
@benlindsey8082
Жыл бұрын
I thought the same thing but the first split second of the video, you can see the key on the shaft.
@danknhaze
Жыл бұрын
@@benlindsey8082 😅 good call!
@lindaorr1028
Жыл бұрын
I saw the same thing.....that first bearing had a key slot.....
@trinium1
10 ай бұрын
that middle bearing is the nicest bearing ive ever seen
@karlringer2648
Жыл бұрын
I bet he never hits a bearing with a steel hammer again
@krisg822
11 ай бұрын
nahh, it's actually fine, especially the way he did it. No bearing got hurt during the making of this video.
@vankoabv
Жыл бұрын
Германские и японские автоинженеров нервно сидят в стороне и курят...
@lukesmith9358
Жыл бұрын
Not really, they should have used another type of hammer on the product piece. It will get damaged.
@StrokeMyLovePump
Жыл бұрын
Dead Blow Hammer.
@user-dv7hq2rh4g
Жыл бұрын
And Russia is completely going down the drain...
@Atreid3s
Жыл бұрын
@@user-dv7hq2rh4g youd be surprised friend. Groceries are cheaper here than in Canada, Germany, France, Norway, etc.
@rafaz705
Жыл бұрын
You destroyed last bearing
@davidroux4900
Жыл бұрын
Sealed bearing Sir....
@henryrollins9177
Жыл бұрын
Nah...
@wymple09
Жыл бұрын
If he did it's the worst bearing imaginable. Barely tapped on it.
@johnridd7547
Жыл бұрын
I totally agree. It was going so well. Did he even hit it straight!😅
@christophergagliano2051
Жыл бұрын
How come that last bearing went in dry no Greece?
@user-xm7tt2zc7x
Жыл бұрын
Молотком по подшипнику без проставки, ну очень технологично))))
@patrickbuildsit
Жыл бұрын
It’s sad that fewer and fewer people get experience how satisfying this is…rebuilding a transmission, steering gear, etc. with cleaned parts and new gaskets and seals.
@brownbee2150
Жыл бұрын
Not an excellent job! Looks like a job of a novice. should have packed both bearings with grease before mounting them. Pounding metal to metal is another no no!
@hellomyfriends9740
Жыл бұрын
Dude listening to that 1030ad music. Dope.
@msameer1458
Жыл бұрын
Yah kitny kv ki motor hy😮
@messemphanger
Жыл бұрын
That lubricant looks delicious!
@MathTidbits
Жыл бұрын
soft lemon curd.
@putripurnama5405
Жыл бұрын
Makan lah
@jimknight2041
Жыл бұрын
Good job but you need more grease.
@Cheepchipsable
11 ай бұрын
He needed to grease the inner bearings before dropping them in.
@abdulrehmanbhatti4945
10 ай бұрын
When a chef becomes automobile engineer 😅
@toniivanova9360
Жыл бұрын
The music is so good. Beautiful
@waterheaterservices
Жыл бұрын
Chinese
@anthonytonello6653
Жыл бұрын
I've rebuilt several of these units part of a centrifuge/strainer equipment. They have a grease line on the bottom. When the grease line brakes they don't last very long.
@drakecadwalladerr9121
Жыл бұрын
It's a cycloidal gear and the grease is likely to be something called "Mollywhite 00 grease" or "FZ Multemp 00" If that helps at all
@vinceradical8910
11 ай бұрын
so its a drive coupling? i stared at it for a while wondering what it was.
@moonstruck7833
Жыл бұрын
Oh wait, I forgot to put the key in.😮
@Trident_Euclid
Жыл бұрын
That's what I thought
@arseniyseleznovveroboj1571
Жыл бұрын
Когда хвостовик напильника лучший инструмент))
@catchingwildmeats
Жыл бұрын
Now just wait 12 hours for the epoxy to set
@dekanatumsa
Жыл бұрын
эстетическое удовольствие...до последнего подшипника (((
@pierangeloguascou.5898
Жыл бұрын
I í9
@__AleM__
Жыл бұрын
Стальным молотком по обойме подшипника?
@MT3-82
Жыл бұрын
В гейропе или СШП обычная практика
@__AleM__
Жыл бұрын
@@MT3-82 И потом ещё добил через проставку по наружней обойме! За такое вообще по рукам надо надавать....
@harshvardhanprajapati698
Жыл бұрын
That ungreased part at the top hurts me the most.....😩😣
@2wheelsurfer
Жыл бұрын
That's why you don't buy foreign parts, hitting bearings with hammer, not lubricating the bearings
@hotrodpawns
Жыл бұрын
Glad this person isn't rebuilding my stuff.
@zuesforceone8087
Жыл бұрын
Rule #12345 if bearing dont go get a bigger hammer.
@vitaliivitalii7763
Жыл бұрын
Какая душевная музыка на заднем фоне, прям так и веет качеством деталей оттуда 😂
@masterdementer
Жыл бұрын
Ngl I'm more curious about that background Chinese music. Let me know if someone knows.
@brianwood7480
Жыл бұрын
Very soothing and calming, eh ?
@carlomagnotm
Жыл бұрын
NLG 1 grease or 00 imo ,not very common to see since most parts use the type 2 but I see the mechanism there might require a constant lubrication flow grease tho
@bigpimp347
Жыл бұрын
Needs more grease.....
@user-baragot
Жыл бұрын
Эй "мастер"... а шпонку кто ставить будет?!
@mirdudut6263
Жыл бұрын
O9
@user-hh6rx5sl7b
Жыл бұрын
Есть там шпонка. Присмотрись. Я тоже думал что нет.
@ka-cr9jj
11 ай бұрын
Мужики видят детали техники со смазкой, Женщины видят груду металла в жиже, Дети видят слайм!
@ThatsSpectacular
10 ай бұрын
Everything was fine until he hammered on the outer race. Contrary to popular belief, you can use a hammer to seat a bearing. However, you must ONLY hammer on the race making contact. If you are seating it into a flange, you hammer the outer race; on a shaft, hammer the inner race. It’s intuitive once you understand.
@user-do7xl7xi7j
Жыл бұрын
Этого рабочего нужно сразу увольнять.
@user-ew8uh4rb9z
Жыл бұрын
لماذا ؟
@user-ew8uh4rb9z
Жыл бұрын
ممكن تشرح لي
@Venic2791
Жыл бұрын
А шпонка подшипника! Как так?
@user-pt1kp4pk8h
Жыл бұрын
Это под эксцентрик… в подшипнике нет паза. планитарноцевочный редуктор загуглите…
@rubenjara914
Жыл бұрын
If anyone’s wondering, you can find that lemon filling at Dunkin’
@1273-ru1fe
Жыл бұрын
😂😂😂😂❤
@robinjacob9590
Жыл бұрын
The half of the people in the comment section complaining about barrels getting beaten by hammer. Tbf majority of them doesn't even work in the factory but talk like they own the shit.
@ricoshay1036
Жыл бұрын
After seeing parts tapped together with a ball peen hammer I wouldn't let this person restore my lawnmower.
@roaringcat1
Жыл бұрын
What do you think he should've used to put the bearing on with a feather?
@brianlangum6253
Жыл бұрын
@@roaringcat1 Come on man, you use a bushing that is the same diameter as the inner race of the bearing, to lightly tap against. Never ever hit the outer race unless you like redoing your work in the not too distant future.
@roaringcat1
Жыл бұрын
@@brianlangum6253 I have tapped them in with a hammer for over 40 years and never had a problem
@1987FX16
Жыл бұрын
Well you that bearing is going to spin on it's shaft. Right for a sec then super loose. Overseas quality right there...
@Jab505
11 ай бұрын
Men this thing gonna work smoother than my life
@vashstampede4878
Жыл бұрын
The ambient sounds + the camera angle made me think he was making street food.
@calvincosby921
Жыл бұрын
MORE COWBELL !!!
@Marfoir0303
Жыл бұрын
I dig it baby 😎
@rso1411
Жыл бұрын
Best skit ever.
@foxymulder2983
Жыл бұрын
Это чё у него там, уплотнительная резинка в луже смазки или одноразовая дистанционная шайба из пластика?
@mauriciogutierrez479
Жыл бұрын
Si quieres una de las mejores transmisiones ok reductores averigua está .
@user-xf1ov6cg9u
Жыл бұрын
распорная шайба...
@user-hm8oz7xc6r
10 ай бұрын
Если нужно забить подшипник, то используй трубку того же диаметра, что и внутреннее кольцо подшипника. Технология провкренная временем. Трубка гораздо более мягкая, чем подшипник
@KITLEVEY
Жыл бұрын
I lost it when he blew by putting the key in the keyway and could no longer watch when he hit those bearing races with a steel hammer and socket.
@robertpanagia7399
Жыл бұрын
Didn't you forget to put the key back in the keyway slot?
@shahbazshahbaz9856
Жыл бұрын
Hey man
@PascaAlexandru
Жыл бұрын
Somebody is gonna have a surprise :)))
@lonewoulves
Жыл бұрын
Key pen is built on to the shaft
@robertg9334
Жыл бұрын
It was there before he put grease oil in at beginning
@thomaswagner3885
Жыл бұрын
Name the Song please ❤❤❤
@TheMRSTEVEN
Жыл бұрын
It's called Peace by Faizal Ishram.
@cowfrank
Жыл бұрын
It's a sumitomo cyclo gear box not a auto transmission. It achieves incredibly low gear ratios the part he is striking in isn't damaged I've assembled hundreds of these.
@scronx
Жыл бұрын
Looks delicious. Can I have the recipe
@user-xk3ne2hc5f
Жыл бұрын
Придётся переделать. Шпонку не поставил
@user-zo7ti5mj7g
Жыл бұрын
Да и по подшипнику молотком.....?
@user-ud2ji3dt9p
Жыл бұрын
Шпонка стоит.
@samuelmartin2817
Жыл бұрын
No pin required, I just beat the snot out of the bearing so it stays in place 😅
@vladj
Жыл бұрын
This apple jam looks so delicious
@user-zd4pw9gv3w
11 ай бұрын
Орбитальный редуктор, просто шедевр. Подшипник так себе по качеству, если приходится молотком запрессовать а не кувалдой.
@drakecadwalladerr9121
Жыл бұрын
Cycloidal gearbox with what looks like FZ Multemp grease. This gear is normally used in applications that require zero backlash
@douglassantosdeoliveirarod5633
Жыл бұрын
Belíssimo esse vídeo!
@user-kz3fv7rt2z
Жыл бұрын
Ну, с такой смазкой, что угодно будет работать!
@U-Thought
Жыл бұрын
Idk but I'm not a mechanic, but there's something I just love about mechanics, maybe it's just fitting joints perfectly and lubricating; and seeing it works perfectly, and complex fun trying again if not
@samuelmartin2817
Жыл бұрын
That's ok this guy ain't no mechanic either
@pauk-0962
Жыл бұрын
Сколько помню, в СССР все молотком собирали, даже телевизор после удара по нему работать начинал😂 а теперь все увидев стук по подшипнику, умничают. Умелые руки, и молотком все аккуратно сделают, а рукопоп, и прессом перекосит обойму.
@Yry_A
Жыл бұрын
Наверное вкусный этот джем...🤔🙂😂
@kevinwagner4233
Жыл бұрын
Don’t worry, none of those plastic spacers will ever wear out, they are forged from pure unobtainium.
@williamroberts6803
9 ай бұрын
Never hit the outside of a bearing that is the center part that is pressed on. It will damage the balls.
@kamilomar9134
Жыл бұрын
THIS MECHANIC IS DOING THIS 100% CORRECT - PUT THE LUB IN FIRST - THEN PUT IT TO GET AND NOT PUT IN THE LUB PIECEMEAL WITH THE PARTS !!.
@Petrolhead99999
9 ай бұрын
So let me get this straight... The inside of the cavity, where no moving parts are making contact, is repeatedly brushed with grease, just to make sure it's still in the empty cavity... But the bearings are installed completely dry? None were packed with grease beforehand?? Why???
@raulhernandochaparrosagamo8014
Жыл бұрын
de los pocos honestos trabajando como es
@farhodshadiev6576
Жыл бұрын
Самое хрупкое в этом редукторе это подшипник с смещенным центром
@heretickle699
11 ай бұрын
Watching him tap the outer race with a hardened steel hammer made me wince
@atomicjellyfish2037
Жыл бұрын
Is it just me or did this guy set the bottom gasket lopsided? And a hammer? Why?! Who hurt you?
@mp-gh2wx
10 ай бұрын
Нормально, последний подшипник заколотил☝🏻🤣🤣
@user-mw5xq3pg3w
Жыл бұрын
только приходиться потом за китайцев потом подшипники смазкой самому набивать, куда пропадает пока едет к нам )
@bladerunner1528
Жыл бұрын
Но мы-то знаем, что такое количество смазки, они кладут только на камеру😁
@pampomasca
Жыл бұрын
키를 꽂지 않았어. 충격이 아닌 압력이 필요
@LoSt-KiLLeR
Жыл бұрын
Молодец. А теперь снимай верхний подшипник и меняй. Нельзя их молотком заколачивать.
@stasuliyacher4009
11 ай бұрын
Вот и молотком по подшипнику, гениально🤣
@jwnagy
Жыл бұрын
The guy singing was the Slim Whitman of Korea. 😂
@964cuplove
Жыл бұрын
Hammering the bearing over both rings is a broken bearing guaranteed make sure to never apply mounting forces through the balls
@StrokeMyLovePump
Жыл бұрын
Me: Nice new parts....... Him: WHACK WHACK WHACK
@uio890138
9 ай бұрын
16 hour shift made him $1.65, but they have socialized healthcare so it’s all good.
@Squishmallows28774
Жыл бұрын
I had to look at the title to realize this isn’t a lemon candy machine
@Zx14rrrrrrrrrrr
Жыл бұрын
That first bearing looks so cool
@user-tc4sz2pn9e
Жыл бұрын
А ещё такая жидкая смазка , при нагреве подшипника превратится в воду.
@ironbeagle1610
Жыл бұрын
Ah yes, the squeaky-bearing-inator.
@svoi936
10 ай бұрын
Вот они технологии высшего мира, к прогрессу в пещеры
@briankilpatrick6039
Жыл бұрын
Pre grease the bearing? No I'll just fill everything and after it's run dry and destroyed it won't look like my fault because the entire assembly was full 👍
@reallybadhabits6610
Жыл бұрын
No mechanic, but I don’t think you should be hammering machined parts with a steel hammer.
@wirenutt57
Жыл бұрын
I assume this is a viscous coupling and the fluid is silicone-based. And never hit steel machine parts with a steel hammer. You should use a brass or plastic hammer. Plus, one person assembling the entire unit just tells me this is some 3rd world country and the labor is so cheap that advanced and modern automated production methods aren't necessary.
@user-qw9gz4qr1e
Жыл бұрын
Сложилось впечатление, что один из сальников (тонкая резинка большого диаметра) не лёг на своё место.
@freakyflow
Жыл бұрын
Poured grease? Roller bearings without the need to pack them? And a steel hammer to set bearings and caps...nice I would fire them
Пікірлер: 1,6 М.