Love the way you narrate as always Ade, it's like the Attenborough of machining! very cool tip thanks so much :)
@AdeSwash
4 жыл бұрын
Glad you enjoyed it, Thanks Sam
@jmtx.
4 жыл бұрын
Awesome! Very nice systematic way of repairing the blades.
@AdeSwash
4 жыл бұрын
Thanks! 👍
@wadestewart9891
4 жыл бұрын
Very good ,never had much luck silver brazing my blades might give it another go. Thanks for the inspiration
@robertoswalt319
4 жыл бұрын
I had a blade break a few days ago. I hated the idea of throwing it away. I may have to give this a try sometime. Thanks for sharing this with us.
@AdeSwash
4 жыл бұрын
Go for it!
@andypandy9931
Жыл бұрын
I remember vertical bandsaws that had a welding attachment a grinder on the back for this purpose.
@eddieholmes5763
4 жыл бұрын
Great stuff as always. Can't see me ever having to do this, but as a beginner it's been a good watch and I've learned something new. Cheers!
@CreaseysWorkshop
4 жыл бұрын
Fantastic. I've tried this and failed. Like all the other commenters I will have to try again!
@AdeSwash
4 жыл бұрын
You can do it!
@donaldnaymon3270
4 жыл бұрын
Great video. Good to save usable blades. Thank you for sharing.
@andrewdolinskiatcarpathian
2 жыл бұрын
What a super idea, brilliantly executed. Well done 👏👏👍😀
@ellieprice3396
3 жыл бұрын
Thanks for a great video. I made a similar jig but found it hard to find silver solder flat strip. Your lifting screw solves that problem by using a piece of round solder instead.
@AdeSwash
3 жыл бұрын
Thanks Ellie, yes it seems to work well, thanks for the comment
@rossgee1091
3 жыл бұрын
If you can't find silver solder shim, just belt the end of a round bit with a hammer and voila! you now have shim!
@robmurg
4 жыл бұрын
Now I've got 'The Ballad of John Henry' going round in my head!
@KCBhandy
3 жыл бұрын
A nice upgrade to the jig originally shown on Toms Techniques
@AdeSwash
3 жыл бұрын
Thanks 👍 Who is Tom? Link?
@birgittamm159
2 жыл бұрын
It's a very good tuorial, Thanks!
@ronsonnenberg6325
2 жыл бұрын
looks good man,got to try it your way
@upthereds4939
4 жыл бұрын
Brilliant job mate
@AdeSwash
4 жыл бұрын
Cheers :)
@zvonibab
4 жыл бұрын
Did good job there Ade, just aneling
@zvonibab
4 жыл бұрын
It will be too brittle other way! Cheers
@therealchayd
3 жыл бұрын
I've got that exact machine (brought at scrap price from retired locksmith), came with a roll of blade, and no idea of how to join it, until now! Thanks!
@johnperkins2509
4 жыл бұрын
Hi Ade. Truly terrific vid. You're very polished at it now. Glad to hear the repaired bands are holding up, cus what I was thinking during the vid was about the temper of the steel at the heated spot. You don't dunk it, so it will be annealed, which is probably the best way. I imagine the teeth will wear very quickly at that point but it's such a small area as not to matter. Altogether GREAT I'd say. :) Great arrangement with your jigs for clamping, grinding etc..
@AdeSwash
4 жыл бұрын
Thanks John, yes as you say it is already annealed from the brazing process, not too woried about re-hardening and then tempering back, a few teeth skipped on the cut dosen't seem to make much difference overall
@grahameblankley3813
4 жыл бұрын
Very good video, however now I've mastered parting off on the lathe with blades I've made from a good quality used circular saw blade, recently I parted off at 800 rpm plenty of lube 25mm dia, so I find hacksaw almost redundant, 🇬🇧 Coventry.
@AdeSwash
4 жыл бұрын
Thanks for the comment Gray, I also part-off when it is appropriate, but I also cut a lot of flat and plate stock, can't do that on a lathe unfortunately. Rgrds. Ade
@oldschoolengineer58
4 жыл бұрын
great content, neat job, thanks for sharing
@AdeSwash
4 жыл бұрын
Thanks for watching!
@marianainsworth9327
Жыл бұрын
Very nice, thank you
@MonstroLab
4 жыл бұрын
This is great! I may mill the back side of an old aluminum heat sync i have for the clamping jig, its about the same size. I lucked out today and bought the last two bands off the shelf they came to my truck like a drive-thru. Wish we had plethoras of Myford lathes over here like in the U.K., Id own one.
@AdeSwash
4 жыл бұрын
Sounds great!
@Machine_NZ
4 жыл бұрын
Awesome repairs Ade. How have the blades held up in use?. Cheers Kevin
@AdeSwash
4 жыл бұрын
Hi Kevin, no problems so far, been using one for about a month without any problems, the one in the vid is a repaired one
@delstone1919
4 жыл бұрын
Nice one ! I always considered welding was the answer to joining/repairing bandsaw blades, but I'll be trying your method neext time I break one. Cheers Ade.
@AdeSwash
4 жыл бұрын
They seem to be holding out ok Derrick, had the last blade on for about a month, possibly longer and it hasnt failed yet, cutting good and strong. Regards. Ade
@rickrick1867
4 жыл бұрын
I find having a good blade is the most important thing with a horizontal bandsaw . having got everything perfectly set up I can cut 20 thou slices with a good M 2 bimmetal blade . the difference is massive . I would like to try Brazing new blades - As I am in England what is a good flux / solder combination please ? I donnt seem to brake many now , a worn out blade is not going to cut straight .
@AdeSwash
4 жыл бұрын
Hi Rick, I used Silver-flo 30 with easyflow powder flux
@davidallison1732
4 жыл бұрын
Would a 15 degree chamfer on the blade ends provide a bigger overlap and consequently stronger joint?
@AdeSwash
4 жыл бұрын
Hi David, yes a shallower angle will work, the more overlap the better I suppose
@TheJimtodd
4 жыл бұрын
I wish I could saw as straight as you by hand
@dfross87
4 жыл бұрын
Does the newly repaired blade beat the worn out old one? More importantly, does it beat an Ade powered hacksaw?
@AdeSwash
4 жыл бұрын
Hi dfross87, the new (repaired) blade works like new, as for the hacksaw, it stay stay in the drawer where it belongs ;) Regards, Ade
@RustyInventions-wz6ir
10 ай бұрын
My stile. I love it
@AdeSwash
10 ай бұрын
Cheers Rusty! :)
@tomshahriari6602
Жыл бұрын
Does the blade need annealing before use?
@AdeSwash
Жыл бұрын
I didnt quench the blade so it will be annealed over the short area of the join, to the teeth in that spot will wear, but the blade just skips over
@couldbanyone9318
3 жыл бұрын
Another gem, keep 'em coming. Great explanation, 'the David Attenborough of machining' 👍🤣🤣🤣🤣 lmao
@AdeSwash
3 жыл бұрын
Glad you enjoyed it :)
@GTRliffe
2 жыл бұрын
straight after brazing when still hot, some shot peening with a sharp hammer would also help in strength
@VAARRR1
4 жыл бұрын
Hi, it is better to use welding
@AdeSwash
4 жыл бұрын
I dont have tig welding equipment, this works well, and is what most model engineers have at their disposal. Rgds. Ade
Пікірлер: 55