Great video. Only thing missing is a healthy application of BLUE Loctite to all the bolts and screws. If you ride off road stuff will shake loose and fall off, usually at the worst possible time, at night, during a hurricane or massive snowstorm, while your running late to be somewhere, and you’re on top of a 14,000 foot tall mountain in the middle of B.F.E. Yes, I have that t-shirt.
@RidgeRoamer
Жыл бұрын
Yes indeed. For additions like this, I typically get everything set the way I want, ride it a little bit to make sure, then go back and add loctite one bolt at a time to keep from anything moving on me.
@garyrowe5984
5 ай бұрын
Great !! Exactly what I was looking for !! Took my laptop out to the garage just now and followed along with my brand new Tiger 900 Rally Pro (2024). Everything went exactly how you showed it , heaps better than trying to get by with just the piece of paper/instruction that came with it. Thank you very much. First video I have watched on your channel , subscribed now !!
@mototripperuk
Жыл бұрын
Thank you so much for doing this video, I did follow another person on KZitem doing it however he got it wrong at the start & never pointed out his mistake, that caused me a lot of bother trying to remedy it, following yours was so simple & easy, thanks again 👌👍
@cmletona
Жыл бұрын
I wanted to thank you for doing this video. I just bought a tiger 1200 rally Pro and I ordered the bark busters. Your video was very hopeful with installation . I appreciate you.
@danharvey6383
Жыл бұрын
Thank you, great video and explanation...worth mentioning, regarding hand / finger protection as well. I had a guy clip me on my throttle side going the wrong way pit riding years ago. I came very close to losing my right ring finger. It was torn badly and required surgery and a long recovery. I wish I had Bark Busters back then lol Adding these is a huge protection to your hands... Safe riding a keep the sunny side up. Looking forward to installing my new Busters on my new 900. Thanks again, great video
@polyrytm
Жыл бұрын
Great video there, RR, and great audio.
@ADV-Rider-Dude
2 жыл бұрын
Thanks mate. I'm just waiting for Barkbusters for my Rally Explorer. Sounds like they will be available soon
@ohTHATaaronbrown
Жыл бұрын
For the record, the kit for the Tiger 900 series will work on the new 1200 series as well, with a tiny bit of adjustment (to avoid hitting the faring at full lock, I flipped one of the bolts upside down).
@65BAJA
Жыл бұрын
Just installed a set on my 900 this evening. Pretty easy. Right side wire bundle is close to the swivel bolt on the bracket. But I ran the cables over the bracket. The lever adjuster for the brake just barely touches the rib as well. Nothing bad enough to impede function.
@jasonpaynerealtor
Жыл бұрын
Looks like we are slowly building the same bike.
@RoadRash1
2 жыл бұрын
I went with barkbusters on the Scrambler. Good decision so far
@Radarman766
9 ай бұрын
Excellent video, thanks for sharing …
@rdintennessee702
Жыл бұрын
Dude, the reason the bracket that attaches to the bar is u shaped is that it goes UNDER the cables so it is a clean run for them. If you notice the way you did it on the brake side, there is interference with the cables and it pushes the bar and lever to not be aligned. Whats weird is that you did it wrong on the brake side but correctly on the clutch side. Just sayin…😮
@RidgeRoamer
Жыл бұрын
I have handlebar risers that have stretched a couple of the cables to their max. I tried. Without risers, easily goes above the bar. With risers it wouldn't stretch that little bit further. I may make something custom to deal with it, but for now it works.
@mark_Hershey
Жыл бұрын
You still running upper crash bars? Appreciate your vid, i was trying to find good pics of them installed to see what they look like.
@RidgeRoamer
Жыл бұрын
Yes I am
@The_RC_Guru
Жыл бұрын
Found your channel with the monkey content and my want of a trailer for mine. Great stuff! My downside in Illinois is it has to be titled and plated therefore a diy for me is probably out of the question. Putting knockoff ish barkbusters on my monkey when they come in the mail. I should look into a speaker like you got!!
@eddale5557
Жыл бұрын
For me it looks like the cables is bent down and vil be a issue later on with a degradation on them from vibrations and so on.
@markvaughn8096
Жыл бұрын
First off THANK YOU FOR YOUR SERVICE... Thanks for your insite on the Bark Busters... I had them on my 2012 KLR 650 with the STORM Wind Guards and loved them.... I'm again bike shopping and went to look at a Tiger 900 Rally last weekend... Planning to rent one next spring to make a final decision...No riding in BOSTON over the Winter hahahaha......... So what Crash bars and Bash Plate did you go with??? (Just watched some IBEX videos ) but had Tourtech on the KLR ...
@RidgeRoamer
Жыл бұрын
Thanks for watching, and thanks for your comment. I went with Hepco & Becker for my skid plate, engine guards, and tank guards. I have videos of each on my channel if you want to see details on those. I am very happy with them, though fortunately I haven't put them to the test yet... Have on previous bikes though, and they were great.
@markvaughn8096
Жыл бұрын
@@RidgeRoamer Yes I came across your other videos.... Thanks!
@a68war
Жыл бұрын
Would the right bracket piece not turn around 180so the bend is at the top due to cable tension? I am thinking about these but also have risers.
@RidgeRoamer
Жыл бұрын
No, because the angle would be wrong then. I need to play with it a bit more and find a better solution.
@Sprinter4x4-TriumphTiger900
Жыл бұрын
Très bonne vidéo !👏🙏
@2alphacpa374
9 ай бұрын
Hi, thank you for your videos. I wanted to ask if you are running bars risers on your Tiger in this video? If so which ones? Thank you.
@RidgeRoamer
9 ай бұрын
Yes, it has risers on. I believe they are the Rox Pivot risers.
@2alphacpa374
9 ай бұрын
@@RidgeRoamer Thank you !
@wobrien1349
Жыл бұрын
2 questions for you…any issues with barkbusters hitting the TFT Screen or wind protection? I’ve seen comments about that. Also, handlebar vibrations at highway speeds and hand numbness?…is it bad?
@RidgeRoamer
Жыл бұрын
The barkbusters are nowhere close to hitting. At full lock, an inch or two clearance. I noticed no changes to vibration. In theory it should vibrate less with more weight and more rigidity.
@Agusta109
2 ай бұрын
The clamps on your handlebars are upside down. They should be mounted over the top of the handlebars, so the cables are nowhere close to the new barkbusters.
@RidgeRoamer
2 ай бұрын
It's odd then that the instructions and every picture the manufacturer shows contradict your statement.
@OSSATR80
Жыл бұрын
Pones un protector por encima de los cables y el otro por debajo, no está bien....
@travisrobertson5119
Жыл бұрын
What handlebar risers are those? Great video
@RidgeRoamer
Жыл бұрын
Thank you! They are the Rox risers. Don't recall the p/n off hand.
@travisrobertson5119
Жыл бұрын
Thanks!
@travisrobertson5119
Жыл бұрын
How tall are they? Did you have to extend any cables?
@RidgeRoamer
Жыл бұрын
@@travisrobertson5119 2" pivoting risers. No cable extensions, but they are definitely maxed out.
@heduardomtzr
9 ай бұрын
Esta al reves la abrazadera, la curva es para librar los cables 🤦♂
Пікірлер: 39