Nice overview thanks. I think when I get a lathe it will be a Precision Matthews. Hope to have my mill running again soon.
@sto2779
8 ай бұрын
In general what would say repeatability tolerance is like for the pm-25mv?
@ogmaker
3 жыл бұрын
Quinn from BlondiHacks recommends a square pipe plug socket for the drawbar.
@tymz-r-achangin
Жыл бұрын
Critical safety tip. Dont loose track of how far your moobies stick out. Can get seriously hurt by the cutters
@MachineBucket
2 жыл бұрын
Thanks for compiling this information!
@kenbeane3112
Жыл бұрын
2 flute End Mills are center cutters, and multiple flutes those can be center cutters or non-center cutters
@incubatork
4 жыл бұрын
Your 2 flute mills are better for slotting most materials not just aluminium, now you have a mill the extra Tnuts you bought are excess, you can make your own. Also unless you do a lot of angle work take the swivel off the vice, they are not very accurate or rigid and it will reflect in your finished work.
@industrialebikes4956
4 жыл бұрын
I have since taken the swivel off of my vise. I am much happier without the swivel.
@industrialebikes4956
4 жыл бұрын
Corrections: (1) I was often referring to the quill as the spindle, and (2) 1/2" T-Slot nuts are too big! I use 7/16" with 3/8"-16 thread T-Slot nuts.
@SuperKingslaw
3 жыл бұрын
2 flute end mills are better for cutting aluminum than 4 flute. Nice setup!
@joewest1972
Жыл бұрын
I just came across your post, I have the same mill, IMO your X feed is too tight. Loosen it, put a piece of paper between the gears, retighten, manually, turn the x axis and roll the paper out from between those gears. Grease the gears and all will be good. Dont keep that x feed that tight
@industrialebikes4956
Жыл бұрын
Great idea
@wags9777
4 жыл бұрын
File or grind when you have a mill?
@Zulda7231
3 жыл бұрын
Good video; thanks!
@jamesbreland2185
2 жыл бұрын
could you do me a fovor ? could you traverse your machine all the way to the left in the x axis. I need to know when in this position what is the distance from the center of the machine to the outermost point with the power feed installed. I'm trying to find out if I have enough room for the power feed on a pm-25.
@burnsm2012
2 жыл бұрын
Great video. 1 question. Where do u get your metal stock from?
@Fernanderas2011
3 жыл бұрын
Thank you for your time in providing all the info., I was planning Grizzly g0704 but , you open my eyes to a better choice, can you please supply the link for the DRO, o insallation for it, I am new to this trade.
@industrialebikes4956
3 жыл бұрын
www.precisionmatthews.com
@stevedunn4490
4 жыл бұрын
Awesome video
@carlspencer4024
3 жыл бұрын
From the sound of the power feed, your gears are to tight. Put a piece of paper between the gears when you tighten the bolts, then rotate the gears to expel the the paper.
@BlueBeemerBoy77
2 жыл бұрын
Thankyou for the video. Are you happy with the size of this machine? Im in the market....
@danielgeorge5239
2 жыл бұрын
How's the rigidity when milling steel?
@euroman12000
3 жыл бұрын
Does your spindle get hot when milling or running at no load?
@CarlPugh
4 жыл бұрын
Greta video thank you! Who is the other KZitemr you mentioned that recommended the parallel set?
@JustinAbrahms
4 жыл бұрын
kzitem.info is the person he's talking about.
@nickminderman7380
2 жыл бұрын
does it come with the dro
@tano1747
4 жыл бұрын
I suggest for oiling up under the table on your x axis ways, you need a proper pump type oil can. The plastic squeeze bottle style doesn't push oil when pointing upward. You weren't oiling anything in the video when demonstrating that bit, just blowing air on the ways.
@industrialebikes4956
4 жыл бұрын
I just got a proper oil can yesterday with my lathe order.
@tano1747
4 жыл бұрын
@@industrialebikes4956 call that a win then! (Of course some would say it is an expensive way to buy an oil can but whatever works...) Actually you could also tell people you got a free lathe with the oil can you needed to buy for your mill. That would sound much more impressive!
@makosharkcnc7730
2 жыл бұрын
how did you get so many subs so fast?
@donepearce
10 ай бұрын
Metric to Standard? You mean Standard to Inch.
@10-4CodyWade
Жыл бұрын
This may be a good video but I can't hear a word you're saying bro.
@robertjordon5782
4 жыл бұрын
How much for this Machine?
@industrialebikes4956
4 жыл бұрын
Depends on the options (e.g., DRO). Check the Precision Matthews website.
@VikramSingh-hf5il
4 жыл бұрын
?
@industrialebikes4956
4 жыл бұрын
Same price plus shipping to India.
@johnbower8785
2 жыл бұрын
What's wrong with you people who create videos that you cannot hear! Don't you ever go back and listen to the video.
@johnnyciantar
2 жыл бұрын
Soon as you mentioned blondie hacks I had to stop watching.
@F1DesignUS
2 жыл бұрын
Yep....that Blondie dude freaks me out!
@silverbackag9790
8 ай бұрын
Just had a look see. What the fck did I just stumble into? I apparently took a wrong left turn in Albuquerque.
Пікірлер: 44