Your teaching format is one of the best I find ok KZitem. Thanks man!
@SolarSolution
3 жыл бұрын
I am glad you are enjoying the channel's content Bartu, thank you for your message. All the best, Jesse.
@blackfaithdoom9018
8 ай бұрын
To understand the combination of Voltage and Amperage , it helped me 1. to imagine a Cliff on a Mountain , the higer the Mountain , the higer the voltage 2. imagine a rock to be pushed of that cliff ..., the bigger the rock the higher the amperage ... 3. the air resistance would be the Ohms electrical resistance ..., while it would be difficult to imagine air heating up ... 😀
@SolarSolution
8 ай бұрын
Thanks for sharing!
@vernroach3413
2 жыл бұрын
I'm 76 years old and still learning...This video helped me do, just that...Thank you so much for doing this.
@SolarSolution
2 жыл бұрын
You are so welcome!
@TechnoEveryday
2 жыл бұрын
Learning is never ending
@ThatGuy-dj3qr
2 жыл бұрын
Clear and concise. Thank you. I appreciate your teaching style. It allowed important concepts to sink into my brain. ☺
@SolarSolution
2 жыл бұрын
Glad it was helpful!
@canyonoverland5003
4 жыл бұрын
I'm here because Primal Outdoors recommended your channel. I'm starting from your oldest video and working my way forward. Thumbs up to you!
@SolarSolution
4 жыл бұрын
Thanks for your message and welcome! I am curious how you will experience the content. Enjoy! Jesse.
@ifyoucantjointhem
5 ай бұрын
Very thorough . Another point on remotely located change controllers is where thr voltage is measured.
@SolarSolution
5 ай бұрын
That is an excllent point you raise there, thanks! I will share a video on this shortly.
@nancyshepheard3868
3 жыл бұрын
Thank you. I have stared clueless, at our Zamp Controller until now. Your video is much appreciated and I have taken notes to include in my personal manual for our 2013 Winnebago Navion. Thanks again.
@SolarSolution
3 жыл бұрын
It is great to hear the video helped you Nancy! Thanks for your message and good luck with the Zamp charge controller. Jesse
@jessicahealey7599
Жыл бұрын
AMAZING! Couldn't understand the pixies until you explained it as your dad did.
@SolarSolution
Жыл бұрын
Glad you liked it Jessica!
@chuckpoz1968
2 жыл бұрын
Thank you ! I just went and bought my led acid 6 volt batteries 🔋 Great value for the money 👍🏻
@CJINW
2 жыл бұрын
You should have went lithium. Same cost and much cheaper in the long run. I just switched.
@adenijiadebimpe1852
3 жыл бұрын
Wonderful. Finally , I have a practical explanation of the difference between voltage and amperage. Thanks to your Dad and you. I have AGM batteries (1500AH Hoppecke batteries) the data sheet specifies that equalization be done every 40days. Your comment on equalization on AGM batteries have me a little confused, would not want my batteries damaged.
@SolarSolution
3 жыл бұрын
Thank you for your message Adeniji, it is nice to hear you enjoyed the video! I am glad to hear you are using the Hoppecke AGM's, in my experience they are top of the line! Not that many people use them due to availability / price. Sorry to have confused you regarding the equalization: The need for equalization of AGM's ultimately depends on the design of each specific battery, since AGM's can differ quite substantially. In my experience with Hoppecke batteries, following the recommended manufacturing settings yields the best possible end results. I hope this helps, enjoy your excellent batteries! PS I love your name, my guess is it is a Nigerian name? All the best, Jesse.
@adenijiadebimpe1852
3 жыл бұрын
@@SolarSolution I must say the batteries are indeed excellent! Yes, your comment helps, I will stick to the manufactures recommendation. and Yes, I am Nigerian! Thank You.
@waylonk2453
6 ай бұрын
Tremendously helpful video! I didn't know that the temperature makes such a difference for battery longevity
@SolarSolution
6 ай бұрын
Glad it was helpful!
@bhaskartalukder600
3 жыл бұрын
your lucid explanation tells us that you know your subject by heart.....very nice....
@SolarSolution
3 жыл бұрын
Hi Bhaskar, thanks for your compliment and it's good to hear you enjoyed the content! Jesse
@arminius301
4 жыл бұрын
Excellent, concise video, exactly the kind of explanation I was looking for. Suggest to produce a video that explains the difference between Lithium ION and LiFePo4 batteries. In fact people seem to accidentally misnomer Lithium Iron and pronounce it as Lithium Ion (omitting the "R" in Iron) probably because they don't know the significant difference between the two. I have not been able to find someone who will explain the dangers of Li Ion and the advantages of LiFePo4 in a well-produced video. Then again, it seems people could care less, in which case the video wouldn't get any views, possibly a waste of time. Thanks
@SolarSolution
4 жыл бұрын
@Arminius thanks for your feedback. I find what you are pointing out very interesting, and you are definitely right that there seems to be a lot of confusion between the terminologies used and the characteristics of the the different types of Lithium-based batteries. I will let my brain chew on it a bit and come up with a proper video. Thanks!
@marcinch3872
3 жыл бұрын
The best explanation on all KZitem 👍👍👍
@SolarSolution
3 жыл бұрын
Thanks Marcin, that is a great to hear! I'm glad the video was useful for you. All the best, Jesse.
@therealrobbycrash
4 жыл бұрын
Thanks, simpel and clear explanation...great job 🤙🏼
@SolarSolution
4 жыл бұрын
Thanks Robby
@radusdirect
3 жыл бұрын
Thanks very much for the detailed explanation of all the stages.
@SolarSolution
3 жыл бұрын
You are most welcome, thank you for your message. Enjoy the channel! Jesse.
@Bosniakov000
2 жыл бұрын
thats simple straight forward absorbed to my mind .. great explained much thanks
@SolarSolution
2 жыл бұрын
'Absorbed to my mind', nice one! Thanks for your message, it is good to hear the video was useful for you.
@rickbartley9255
2 жыл бұрын
Thank you for the well done overview. I enjoyed the refresher.
@SolarSolution
2 жыл бұрын
Glad it was helpful!
@wilfredomarino3413
3 жыл бұрын
Thank you sir.we learn so much all in your video
@SolarSolution
3 жыл бұрын
Hello Wilfredo, thank you for your message. I am glad to hear you appreciate the videos. Keep on learning! All the best, Jesse.
@dimitrisgeorgiadis2528
3 жыл бұрын
Dear Jesse thank you for sharing your knowledge with us ,wishing you health and prosperity . I would like to ask ,me and my wife have builded tiny homes for us and our children off grid , I have realised that the diseficiency of solar power is the batteries ,too expensive and no guaranty how long they will last ,oi have bought strong golf batteries 245A power , In your video if I understood well you are talking about bubbles and you say it's not good for the batteries ,my batteries Bubblé everyday ,what I'm doing wrong I don't want to destroy them ,my charger is a 3 stage charger in an inverter set to 54v floating and 56.4v bulk ,any suggestions?
@SolarSolution
3 жыл бұрын
Hi Dimitiris, thank you for your best wishes. I cannot provide you with personal advice through the KZitem comment section, sorry for that. To get direct support, contact me through www.solarsolution.co/services. Good luck with your system! Jesse.
@nicolasbarcet2689
4 жыл бұрын
Thanks Jesse. Great video! Can't wait for the Lithium battery version! ;)
@SolarSolution
4 жыл бұрын
Coming soon!
@SolarSolution
4 жыл бұрын
Thanks for your suggestion regarding the Lithium battery topic Nicolas, I have upload a new video here: kzitem.info/news/bejne/0nqG24Wbk3uZemk
@JehanzaibTraders
21 күн бұрын
Your video is very informative and precise. I want to know about flooded battery installed at home are placed at one place for long time un moved. Does moving/shaking them after regular interval have any affect on their life and efficiency?thx
@SolarSolution
21 күн бұрын
Good question! Shaking/moving is probably not a good idea, since it could accelerate 'plate shedding' and possible short plates due to plate debris at the bottom moving around. Stratification of the elecrolyte is what one would generally try to avoid/reduce by regularly going through the absorption phase: In the absorption phase the bubbles in the electrolyte would mix the electrolyte and hence reduce stratification.
@dhirchie4877
3 жыл бұрын
Great video, very easy to understand! I’d like to see a video of your opinion on the different types of charge controllers (had a look at your channel but couldn’t find one)
@SolarSolution
3 жыл бұрын
A great suggestion, thank you for your message. There is indeed no video on this topic yet. I will make one and notify you once it is online. Thanks! Happy new year, Jesse.
@rv_planet
2 жыл бұрын
Great video!! It'll help program my new voltage regulator for my rv!! Thanks again!
@SolarSolution
2 жыл бұрын
Great to hear!
@mnmarcella14
3 жыл бұрын
very good simple explanation
@SolarSolution
3 жыл бұрын
Glad you think so Michael! Thanks, Jesse
@PrimalOutdoors
4 жыл бұрын
Thank you that was very clear and I learned a lot about the stages of charge 👍
@PrimalOutdoors
4 жыл бұрын
A video topic I would like to hear your opinion about would be some detailed information on charging a deep cycle battery on a alternator. It seems to be the general consensus that is a bad idea, but I have never read or heard someone explain why, an alternator with single stage charger can't full recharge a deeply discharged battery. You explained how a 3 stage charger works but what does a single stage do? Jason
@SolarSolution
4 жыл бұрын
Hi Jason, thanks for your feedback. An excellent and valid question, I will share a video on this shortly!
@PrimalOutdoors
4 жыл бұрын
@@SolarSolution I will be looking forward to it thank you 👍
@SolarSolution
4 жыл бұрын
Hi Jason. As promised, here is my response to your question about charging your deep cycle house battery with your alternator. I hope it will be useful for you. [Time stamped, specific to your question] kzitem.info/news/bejne/tXd74HeZmqt6Y5w [Complete video] kzitem.info/news/bejne/tXd74HeZmqt6Y5w
@chico711
11 ай бұрын
Do we need to let the batteries rest after equalization ( disconnect charging and loads ) and for how long please
@javahaxxor
Жыл бұрын
It would be interesting to understand what happens with a dead car battery, in my case a lead/acid one. My CTEK charger charged it from "dead" (2 leds out of 8) to full in a few hours, but it lost its charge until morning, and now it's staying at 2 leds for hours, and both the charger and the battery get hot. I can hear bubbling inside the battery. When is it a lost cause, and why ? This was bought new a couple of years ago then kept in storage where it deep discharged
@ukachionyema5861
2 жыл бұрын
Thank you. This is helpful. I wish to regulate the charging in a system that drains battery power really fast. What is required to make the charging relatively fast and not overcharge?
@organicngreen9156
2 жыл бұрын
Great Explaination .Many Thanks and Best Wishes !!
@SolarSolution
2 жыл бұрын
Glad it was helpful!
@ramzeneger
2 жыл бұрын
Thank you and thank you and thank you a million times!
@edinfific2576
2 жыл бұрын
Maybe you could also mention that a plastic mixer could be placed in each cell of a large wet lead-acid battery to stir the electrolyte periodically without causing the gassing and shedding, which would slightly simplify charging and extend battery life.
@benkanobe7500
2 жыл бұрын
Please go into detail about charging LAB (flooded, AGM, Gel) arranged in strings of series-parallel. I have large AGM batteries repurposed from a data center that were never cycled I am using them for my off-grid solar at night. My inverter would prefer 36+VDC but will operate on 24+VDC. My batteries are 12V. I want to arrange them 3 in series and then two banks of three in parallel. I get VERY mixed information about how to use my charge controller to charge them during the day. Lots of information saying my middle battery in series will be damaged during load and unequal charging will happen. What is this all about? How do I (schematic??) arrange my batteries so they charge correctly each day. I live in Southern CA and have excellent true south exposure from sunrise to sunset for my panels.
@samulil6957
Жыл бұрын
Thank you for your videos. Charging current of a wind generator fluctuates a lot. Does the fluctuation harm the battery?
@kallio316
4 жыл бұрын
Great video can't wait to see more 👍
@SolarSolution
4 жыл бұрын
Thanks Chris, it is nice hear you enjoyed the video. One new topic every week, I will upload the next video in a few hours.
@core-texlabs.officialchann4118
2 жыл бұрын
Hi, I have had all my AGM batteries gassing away during absorption and wondering how I can reduce the gassing, the problem is that even though they are fitted with catalyst caps, the recombination is far to be fully effective, its seems that this catalyst is a bit of a gimmick. What to you would be the lowest voltage that is acceptable for absorption and how much can we compress the absorption time down to? It is really hard to find this information online.
@AbdulSamad-hd1sr
2 ай бұрын
What should be the equalisation voltage of floaded battery. For 48v system
@SolarSolution
Ай бұрын
I recommend following the manufacturers guidelines. Thanks!
@betaenvironmental5168
2 жыл бұрын
Hi, why does AGM & GEL batteries do not support equalization
@TechnoEveryday
2 жыл бұрын
These batteries have different physical and chemical structure than lead acid type
@clarkvalcoic1736
2 жыл бұрын
Hi Jessie. Love your shows they are very professional. If I have 60vdc and 10 amps coming from my panels going into a 100v 40a mppt controller to a 12volt 200amp lithium battery at 50% charge(13v), what should the volts/amps going into battery? should I be getting roughly the same watts into batteries as going into controller minus inefficiencies.? thanks Clark
@latissimus8
3 жыл бұрын
Thank you for all that helpful information! It would also be interesting if you said something about desulphation devices like "megapulse".
@SolarSolution
3 жыл бұрын
Hi Lars, thanks for your message. It is good to hear you enjoyed this video. You have an excellent question regarding de-sulphation devices: I discuss this in the following video I shared: kzitem.info/news/bejne/xKKM2Jd9cZyHao4 Let me know if you need additional information! All the best, Jesse.
@AbeAlJ
2 жыл бұрын
Hi Jesse. You mentioned that you can connect a temperature sensing device to your charge controller wirelessly. Can you share an example of a wireless temperature sensing device and how to connect it? And also a hard-wire connection like you also mentioned. Thanks.
@ocrun6765
2 жыл бұрын
Thank you for the explanations. Is Equalization the same as desulfation? Will desulfating gel or AGM batteries damage them?
@SolarSolution
3 жыл бұрын
Course trailer and Coupon Code: kzitem.info/news/bejne/t4GXxa14oqdoZW0
@neomatrix2722
5 ай бұрын
Thank you for sharing I have a question can you talk about you know measuring yourselves and you know give us specifics like how like I'm not sure how to read the fractal meter so in other words what numbers should I look at how far apart do they need to be for me to equalize
@SolarSolution
5 ай бұрын
An excellent question, thanks! I will share a seperate video on this.
@sekyanzinathan7521
3 жыл бұрын
Thanks for a good video. I would like you to explain if is possible to do equalisation using solar pv
@SolarSolution
3 жыл бұрын
Great suggestion!
@mujahidali6988
3 жыл бұрын
Thanks a real illuminating video
@SolarSolution
3 жыл бұрын
Thank you for your message Mujahid, it is good to hear you enjoyed the video. All the best, Jesse
@walidaitkhelifa8028
3 жыл бұрын
Could you make a video about classified zones of battery rooms because of the hydrogen emission of the batteries. You said in the video that we may install the charge controller in the same room but the classification of the local containing the batteries requires an Ex protection mode that should be considered in the controller.
@SolarSolution
3 жыл бұрын
Hello Walid, thanks for your suggestion. I will add it to the list! Jesse
@DunOpondo
2 жыл бұрын
Great video, very informative 👍🏿
@SolarSolution
2 жыл бұрын
Glad it was helpful!
@billybuenafe7634
3 жыл бұрын
here's a question: can you use your battery at any different stages of charging or you have to wait until float charging... my controller (solar charger controller) always indicate "MPPT" and I have not seen the "floating" stage yet. So I'm not sure when to safely switch to battery use. Thanks and more power.
@ashforkdan
2 жыл бұрын
Finding the settings for a 48 volt 540 amp hr lead acid forklift battery for charge controller settings. 25,920 watts what's the best amps to recharge.
@sreekumarUSA
3 жыл бұрын
012520/2058h pst... Thank you very much for the explanation on Absorption, Bulk and Float terminology in PV Cell Systems. It was different kind of terminology for many people including myself. But you explained it very well, and being a layman, I could understand well. I have subscribed to your class and look forward to learning more in the future. Regards, stay safe, stay Blessed and 73s...
@SolarSolution
3 жыл бұрын
Thanks for your message Sree, and welcome to the channel! Jesse
@isabamhimod2829
2 жыл бұрын
Thank you
@SolarSolution
2 жыл бұрын
You're welcome
@abiezerdejesus5759
4 жыл бұрын
I want more information about charging
@SolarSolution
4 жыл бұрын
Hi Abiezer. Can you provide more details about what kind of charging topic you are interested in.
@QUADBOYification
3 жыл бұрын
Good info, thanks. What I wanna know is if a Lead-Acid Battery degrades after a full year of use and if you should change the float voltage on the solar controller to a lower voltage. If my Battery is working OK but can only charge up to 13.2v isn't it harmful to keep the float-charge-voltage at 13.8-14v?
@SolarSolution
3 жыл бұрын
Hello Robbert, thanks for your message. It is good to hear you enjoyed the content. For personal advice you can contact me through www.solarsolution.co/contact
@bestillandknowthatuaregod
2 жыл бұрын
For a CTL70- 12V what is the battery charging voltage ?
@EdArseneau-ul3nd
Жыл бұрын
It is mentioned the charge current is a function of the Ah rating of the battery, but how does the charger know the Ah rating of the battery? How does a battery charger differentiate between 100 Ah battery and a 200 Ah battery?
@biggybiggy84
Жыл бұрын
It doesn't. He said that when it reaches a certain resistance that it triggers something in the circuitry of the charger to start the absorption process. The absorption charge rate could be a preset amperage value in your charger common for your type of battery (doesn't matter the ah). Only after it reaches a certain time or the amperage reaches an almost equilibrium state that threshold is met and you have reached float value. The charger should stop charging after this? But we know my cheap lead acid charger will keep charging at the 2a setting i selected and bubble up excess energy from the battery until you unplug it. Now ah rating is important because you dont want to charge it faster than the 20% ah rating for your battery. If you pick up a 5a output charger and charge a 25ah battery that would be 20% the max charge rate you can safely use. You need to check the absorption rate of the charger for compatibility with your battery. I got a battery cooking now I need to check on. Nothing smart about this one. I was going to add that is why I start my charger on a high setting for a low battery and after it reaches a certain voltage around 80% of float value I turn it down to the lowest setting and this has always gave me a strong car battery. It does give me a green light so maybe it does shut off I dont know. I've had some bad batteries come back to life after a really slow charge for extended periods kinda resets them or something. I think they call it battery conditioning.
@19SmokeyJoe94
3 жыл бұрын
Good video, dude
@SolarSolution
3 жыл бұрын
Thanks Smokey Joe, it is nice to hear that. All the best, Jesse.
@chico711
Жыл бұрын
Do we have to remove the caps while equalizing
@evasmith4143
3 жыл бұрын
What’s the difference in real life between deep cycle and a car battery and how to check your amp and the battery whether the car or the boat by checking the amps can you figure out what’s the amp power to that battery thank you
@SolarSolution
3 жыл бұрын
Hello Eva, thank you for your message. You have an excellent question, which I have not covered yet; The difference between start & deep cycle batteries. I will share a dedicated video on this soon. As for the second part of your message, could you perhaps clarify your question a bit more: What is it that you want to learn? Thanks. Jesse
@user-rz3ro9lu6o
3 жыл бұрын
Thanks so much for the video. Very informative. I have a Mastervolt 50A/3-channel charger, connected to 4x 6v lead acid batteries by Interstate, (2 other channels of the charger are for start batteries). Batteries about 3 yrs old, and never been equalized. My bad. The charger appears to be able to do only a poor job of equalization since it only approaches the equalization voltage and stays there for a short time. And Interstate indicates that equalization should be done for 2 hrs at the equalization voltage. Can you advise any special equipment or setup that would allow for proper equalization to be performed on the batteries?
@SolarSolution
3 жыл бұрын
Hello D, thank you for your message. It is good to hear you enjoyed the video. As for your question: Do you know whether you can adjust the settings in your charge controller?
@user-rz3ro9lu6o
3 жыл бұрын
@@SolarSolution You can only adjust the equalization voltage. You cannot adjust the duration of how long the charger stays at the equalization voltage. I am actually considering the purchase of a DC power supply that has voltage and current settings so that I can adjust what is applied to the batteries during equalization. I realize that I will need to ensure that the batteries are isolated from all loads and chargers when I apply the DC power supply output.
@geraldzollneryoga3486
3 жыл бұрын
Wow, great explanation! Finally I understand the differences! :) I do have one small question though, if you have time...my solar charge controller is pre-set to go to floating charge at 13.8V and to equalizing charge at 14.6V, however the label on my battery says floating charge should be activated at 13.5V and equalizing at 14.1. Do I have to be concerned about these differences? Unfortunately I can only change the preset by adding a bluetooth controller, which is very difficult to get here in Peru. Please let me know if you think that's really necessary or if I'll be just fine with the preset settings! Thank you! (btw: I'm not sure if it matters but I actually run two of these batteries in series because my system runs at 24V).
@SolarSolution
3 жыл бұрын
Thank you for your message Gerald, I am glad to hear you enjoyed the video. And nice to hear from somebody in Peru!. Unfortunately I cannot provide you with technical advice through the KZitem comment section. Sticking with the manufacturers recommended voltage settings is often wise. Overcharging a battery can [among other things] lead to accelerated aging, case bulging, and excess loss of electrolyte. This being said, the flooded lead acid battery are less sensitive to overcharging [and other forms of abuse], compared to the AGM and GEL types. I hope this helps, if not you can contact me directly through the main website. Good luck! Jesse
@geraldzollneryoga3486
3 жыл бұрын
@@SolarSolution Great, thanks for the quick reply! With what you said in mind, I will try to get the bluetooth extension, but at the same time not be worried about my batteries until I get it (probably in a couple of months)...Thanks for the advice! Have a great day!
@SolarSolution
3 жыл бұрын
You are welcome Gerald, glad I could help. I wish your bluetooth extension will arrive soon! Would be nice to hear how it turns out. All the best, Jesse.
@handisc
4 жыл бұрын
thanks for useful information. by the way, does the battery have high AH means last longer than low AH, including discharging time and lifetime?
@SolarSolution
4 жыл бұрын
Hi Handis, thank you for your message. I will upload a separate video on battery capacities soon, I am sure this will answer your questions. If not, just let me know.
@Dzikr_Family
2 жыл бұрын
Terbaik... 👍👍👍👍👍
@AnilMaurya-cb8bx
3 жыл бұрын
Dear respected sir Please. Make a vedio on 150 - 200 AH. Lead acid battery for 1. Why. Equalization is required for lead acid battery 2. How a battery cell are being over charged and under charged when 6 cells of battery are used the same current and voltage from inverter .... 3. How can we equalize the battery in series like 2 battery inverter of 24 volts as 1500 va .... 4. What should the current and voltage and charging time and ideal process to equalize the lead acid battery Please help ..... Anil maurya(Architect) India
@SolarSolution
3 жыл бұрын
Hello Anil, thank you for your excellent list of questions. I will create a dedicated video on this, and let you know once it is online. All the best for now, Jesse.
@AnilMaurya-cb8bx
3 жыл бұрын
@@SolarSolution Thanks a lot sir 🌻🌻🌻🌻🌻
@Cdswjp
Жыл бұрын
Nice
@SolarSolution
Жыл бұрын
Thanks
@danasmith7171
4 жыл бұрын
Very good video.
@SolarSolution
4 жыл бұрын
Thank you Dana, I am glad you enjoyed it.
@AnilMaurya-cb8bx
3 жыл бұрын
Please Make a vedio on equalization Especially Anil maurya India
@SolarSolution
3 жыл бұрын
Hello Anil, thank you for your message. I received your other request as well: work in progress!
@askdomisset
2 жыл бұрын
Coolest
@ashleyhenriquez2594
3 жыл бұрын
Why does the Inverter goes from bulk charge to float charge without going to Absorption stage ???
@SolarSolution
3 жыл бұрын
Hi Ashley, thanks for your question. There can be several reasons behind this effect, I would need additional information in order to answer your question. The settings in the inverter would be the first point of interest. Good luck! Jesse
@sassy_gamer7899
Жыл бұрын
Hi I’m not very smart I just purchased a electric motorbike lithium ion battery it says something like “once light turns green and fully charged allow float charging for 1-2 hours does this mean leave it plugged in when it’s full charged for 1-2 hours 😅
@biggybiggy84
Жыл бұрын
Yes, First stage bulk max rated charging up to 20%ah rating. They probably advertise how fast the green light comes on. They say float but I bet you its the absorption stage where the charge controller lowers the current due to the first stage completion re battery voltage and slowly finishes the charge till float (100%) as the video explains. You could test using a dc amp clamp. Or possibly using a regular volt meter set to dc, unplug the charger after the green light comes on and check the bikes battery voltage by touching your leads to the harness connections for your bike. Plug it back in for 2 hours and then check the voltage again. That reading should be close to your float voltage. Find the nominal voltage (lower than the green light value) the factory says the battery is and subtract from your float voltage (highest value). Example: Lets say you get get .5v difference (that's usually what i get from a single cell 18650) from nominal (shipping factory voltage) to float. Divide by 10 would be .05 so if i'm right your green light came on after 80% charge meaning .05 x 8 = .4 volt increase, in this example, from nominal voltage would be 80% and another .1 volt (20%) increase would be the float charge. Also if you know the battery cell make up you can find the battery factory voltage and see how many times they ran it in series to come up with the voltage rating they provide. So if its 18650 cells the voltage is I think 3.7v lets say if your bike says 48v then the batteries ran in series 13 times and the voltage more accurately would be 48.1v. So knowing the cells really helps make this test for more accurate. That .1v could mean 20%. Sounds crazy but if you run it in series 13x's that .5 x 13 = 6.5v divide by 100 = .065 that means .1v may only be about 2% of a higher voltage system. That sounds more like it. I could be wrong but I doubt it.
@tozejulio
3 жыл бұрын
Hello friend, I'm writing from Portugal, I really liked your video, I wanted to ask a question about what is happening to me in my off grid system, 2 or 3 days ago I put my inverter to equalize to 31.4v, but it just arrives at 30.6v, and it doesn’t go up, which may happen, today I did the same thing and the same thing happens, the voltage doesn’t go up, I have 12 batteries (2v cpzs 930AH) only have 9 months of use ... hope you can help.
@SolarSolution
3 жыл бұрын
Hi Toze! Thanks for your message, it is good to hear you enjoyed the video. I would like to help you, though unfortunately I cannot provide personal support through the youtube comment section. You are welcome to contact me through the main website: www.solarsolution.co. Good luck! Jesse
@waqasnaeem4908
3 жыл бұрын
Lifepo4 battery does'nt need float charge if use normal 12 volt lead acid charger on 4s lifepo4 12v pattery pack with daly bms is it ok? Or harmfull my cells?
@SolarSolution
3 жыл бұрын
Hello Waqas, thank you for your message. I will share a video on this topic in the near future, stay tuned. All the best, Jesse.
@ashleyhenriquez2594
3 жыл бұрын
Why does a battery drops in voltage right after charging for Ex after float 26.6 volts itvdroos down to 23.3 right after charging ? I'll aporeciate if you could Answer myvm questions.thanks already
@SolarSolution
3 жыл бұрын
Hi Ashley, thanks for your message. Imagine that you are inflating the tire of your bicycle: While you are pumping, the pressure in the pump itself is quite high, and forces air into the tire. The pressure of the tire will increase, although the pressure in the pump will still be higher than that of the tire. Similar to inflating your tire, you will need a higher voltage from your charging device, in order to "inflate" your battery. When you will stop charging, you will now see what the actual "pressure" in the battery is. The voltage you are seeing during a charging cycle is the voltage produced by the charging device. I hope this helps! Jesse DISCLAIMER: Don't try to charge your battery with your bicycle pump :)
@randy1138
2 жыл бұрын
Batteries for my UPS system has 300AH. I'm now trying to upgrade it to 330AH batteries. Cell voltage and everything else is the same. Do I need to change the battery charger settings? If so, how? Can you please help me out with this? Thanks 😊💯
@aungkyawthet9935
8 ай бұрын
Hello, etai solar battery 200ah 3pcs not equal voltage how does it make?plz answer me.11kw inverter 3pcs connect to battery.
@ramzeneger
2 жыл бұрын
Can you do about lithium phosphate, lead acid is like world war 2. We need a video about lifepo4 pls.
@jeandede3382
3 жыл бұрын
What max charge current should be used for an AGM 660ah battery park?
@SolarSolution
3 жыл бұрын
Hello Jean, thanks for your question. I did not see which brand or model of battery you are using: What does the manufacturer's specifications recommend? All the best, Jesse.
@jeandede3382
3 жыл бұрын
Eversol 12V C20 220Ah / C5 185Ah AGM
@michaelthompson5213
4 жыл бұрын
HI i want to ask a question because i am confused i have 8 6v 225 amp us lead-acid battery connected for 24v system 2 strings of banks in parallel make it 450 amp. and also a flex max 60 amp charge controller. can you tell me the correct settings for the absorption float and Equalization please and thaks
@SolarSolution
4 жыл бұрын
Hi Michael, thanks for your question. Have you checked the battery specs yet?
@michaelthompson5213
4 жыл бұрын
seems to can't find it for my batteries its power king same thing as US power 6v 225 amp each. my system is wired for 24v 2 strings of bank
@SolarSolution
4 жыл бұрын
Ok I understand. For help, check www.solarsolution.co/services The 'Instant Consult' option would help you out.
@Lee-Fiz
2 жыл бұрын
Hi, im new in this, is SLA battery the same as a AGM battery? I also seen some video they did revive a SLA battery by putting battery water inside it, does a SLA battery a dry battery, by putting battery water would damage it?
@shlomyshefler4898
Жыл бұрын
Thanks for your explanation. What about battery electronic desulfators? Do they actually work? Or only the hi end professional ones do? I have seen some dead battery pb battery recovery with a spot welder- can you please elaborate on this topic- the voltage and current figures on this spot welders are way higher than recommended but I have seen this method work many times. What are the pros and cons to this method ( except the safety aspect of course) And would it suit any type of pb battery or just flooded due to the need for removing the caps for releasing the pressure and topping up water? Thanks in advance for your reply 🙏
@SolarSolution
Жыл бұрын
Hello Shlomy, thank you for your message. I think the following video will answer most [if not all] of your questions: kzitem.info/news/bejne/xKKM2Jd9cZyHao4. Have fun! Jesse
@jamesthebond0072
3 жыл бұрын
Just to make it quick can anyone tell me why my 48v20ah you battery is charging to 55v 3ven with a 2a 48v charger? For lithium though? Cant find anything anywhere
@SolarSolution
3 жыл бұрын
Hello James Bond, thank you for your question. Perhaps you can clarify which type of charger you are using, and what the charger settings are? Perhaps Q can also assist you. All the best. Jesse.
@muhammadaqilkhan7999
3 жыл бұрын
When often should we equalize the flooded battery ?
@SolarSolution
3 жыл бұрын
Hello Muhammad, thank you for your question. Have you checked the recommendations of the manufacturer of your battery yet?
@muhammadaqilkhan7999
3 жыл бұрын
Yes Sir, I have checked the battery specification they mentioned only bulk and float voltage and did not mention the equalizing voltage and it's period.
@muhammadaqilkhan7999
3 жыл бұрын
It's 12V Hyundai tall tubular battery 155 AH.
@orlandomccray6878
Жыл бұрын
What type of 24volt charger would i need to charge 8 solar batteries at night.?
@Ibian666
Жыл бұрын
What would happen if you used a dc to dc converter instead of a normal controller for solar? They can accept variable input and the output can be set to a specific voltage. Why not set it at the float voltage and save the money for a controller?
@biggybiggy84
Жыл бұрын
I did find this: Recharging deep-cycle batteries with a charger using a constant voltage or a fixed charge algorithm can, over time, lead to a condition called stratification. Stratification occurs when the acid in the electrolyte separates from the water and settles to the bottom of the battery causing damage
@ui2p0
4 жыл бұрын
what's the story of percentage meter? even when fully charged, my liquid acid new battery is showing about 50%. And also - can my solar charge controller receive also input from a wind turbine on top of the two solar panels it gets and still manage the charging or do I need a separate controller for the wind turbine (assuming both turbine and panels do not exceed the max capacity the controller can handle)
@SolarSolution
4 жыл бұрын
Hi Yoramedia. Thank you for your questions. I have a script ready for a video on State Of Charge indicators like the one you are mentioning, so I am sure this will answer your questions. The video will follow in the coming weeks. It would be a bit challenging to explain the topic in this comment only. As for the the charge controller question, I would definitely recommend to have a separate charge controller for your wind generator. I hope this helps, enjoy!
Пікірлер: 166