Wow, you did a really great job explaining everything. Now i know what to look for.
@MrSteppingstone888
11 ай бұрын
👍👍
@Double-xposure
11 ай бұрын
Sir i was seriously thinking since last few days about you have not uploaded any video since last few months thanks in advance for this informative video i will watch it tonight full i don't have enough internet data to watch this whole video on at least 720 resolution so i will download this in my office on wifi so i could watch it later at night peacefully
@MrSteppingstone888
11 ай бұрын
Hi Often things happen in between that I have to take care of that makes the video I may be working on take longer to finish for example this came along and put the video I was working on on hold
@GarnetCarmichael
11 ай бұрын
I didn't realize you were so well equipped, nice set up. Interesting points made too, learning as I go. It's a good thing we aren't neighbors, I'd be a real pest...lol. Thanks for this one!
@MrSteppingstone888
11 ай бұрын
👍👍
@tiltedflip4491
10 ай бұрын
Thanks.Always a pleasure.
@MrSteppingstone888
10 ай бұрын
Thank You !
@peteralexben
11 ай бұрын
that 97 k is one of the best springers you can buy
@drichi07
11 ай бұрын
Good information as always. I had never given much thought to breech seals except to (crudely) check for leaks and fit when replacing. That may explain some of the problems I have had.
@MrSteppingstone888
11 ай бұрын
Hi Yes piston seal when worn can give you inconsistent groups and in proper breech seal
@peteralexben
11 ай бұрын
i do check the barrel .cilinder allignment with a level , the cilinder in a vice or gun rest set level ,the barrel must be level to. sometime a file is needed to remove some metal . but then you get a barrel with less swinging
@briandetrick2688
11 ай бұрын
thankyou so much for your videos
@MrSteppingstone888
11 ай бұрын
👍👍
@peteralexben
11 ай бұрын
i look how the breach seal print around the transferport ,if its small it needs a shim , if its ok its a litlle smaller then the seal thickness its ok
@hanskrohn3206
10 ай бұрын
Both are 22caliber. Northeast Pennsylvania
@springpistonriflefeverlone9611
11 ай бұрын
Your teaching about pellet to boar test helped me get a good Hatsan 95 and 125. But the pivot bolt 🔩 on the 125 doesn't tighten up the forks enough. I might have to take my pivot bolt to a machinest to add an extra thread. What do you think? I appreciate your answers Mike.
@MrSteppingstone888
11 ай бұрын
just now saw this I did not get a notification See how the forks fit if they have a gap and fit up loose ask him to make you some pivot washers first, that maybe your bigger issue you can take him the receiver with internal pulled out. some of the hatsans are not made Propper and the forks are to far apart/ just be sure he makes them even so the barrel shifts to its center of the fork
@springpistonriflefeverlone9611
10 ай бұрын
@@MrSteppingstone888Thank you
@MrSteppingstone888
10 ай бұрын
@@springpistonriflefeverlone9611 👍👍
@peteralexben
11 ай бұрын
i saw that the prices for weihrauch airguns are set much higher in europe then a few years back , 200 eur up on a hw 100 .
@MrSteppingstone888
11 ай бұрын
Yes I think it was because the U.S. dealer AOA complained as a lot of U.S. folks were buying from Krale receiving guns in 3 days. Then I noticed the U.S. seller AOA lowered their prices some and Krale raise their price
@CubGrylls
11 ай бұрын
I picked up a new hw50s .22 last week. After cleaning the barrel I pushed some pellets through to get a feel for the bore the breech section very tight, followed by a looser section (not enough for the pellet to fall), then the choke. Havnt had much time to shoot it. Any suggestions would be appreciated
@MrSteppingstone888
11 ай бұрын
Thats one of the scenario the block area squeezing the pellet down making the rest of the bore not as snug. The good news is the pellet has some consistent bore fit. you could do a light bore polish with JB Bore Brite mix it with a little oil then smear it on the soft bore mop just don't go crazy and then be sure to get any excess polish out/ you could work the barrel block area the most and just a little on the rest of the bore
@mchammer256
11 ай бұрын
Interesting to see a strip down rebuild of the 97. More power better accuracy loud or quiet dose not matter to me as long as it dose the job. Mine is loud about 11ftps but accurate over 20 yards or 60 feet using wasp pellets.
@MrSteppingstone888
11 ай бұрын
It was a Beeman R -9 that came in for repair but the 97K in last clip just because I shipped the R -9 back to the owner / love both guns lol
@airgunnersc9335
11 ай бұрын
Hey Mike. What is the purpose of the knock outs? I always enjoy your videos. Thanks
@MrSteppingstone888
11 ай бұрын
they lock the end plug from being able to come out where it would be under a lot of spring tension
@airgunnersc9335
11 ай бұрын
I'm still do not understand the knock outs . Why doesn't Weichrauch just make a solid tube with no knock outs?@@MrSteppingstone888
@MrSteppingstone888
11 ай бұрын
@@airgunnersc9335 LOL GERMAN ENGINERING / I said the same thing, it adds extra holes on the tube, it would bee better with out that deign
@hanskrohn3206
10 ай бұрын
Do you buy lightly used rifles? I have a Beeman R9 and a Diana 48 that I can’t shoot any more. Both in original boxes.
@MrSteppingstone888
10 ай бұрын
what cal is the R 9 and where are you located Thank you
@hanskrohn3206
10 ай бұрын
Both are 22caliber. Northeast Pennsylvania
@MrSteppingstone888
10 ай бұрын
@@hanskrohn3206 Hans here is some info to reach me. no caps no spaces etc replace dot with the . and at with the symbol a w a y s m i k e at h o t m a i l d o t c o m
@johnhauser4801
11 ай бұрын
Thanks for the info Mike. I have a HW97. What would you use for the best tunning kit for sup 20 fp.?
@MrSteppingstone888
11 ай бұрын
I would go with VORTEK product inc a least he has kits
@peteralexben
11 ай бұрын
@@MrSteppingstone888 if needed in europe you can have tuning kits from airghandi named airjoe from germany and from tbtair rifle tuning he got short stroke kits to from uk both have yt channels
@MrSteppingstone888
11 ай бұрын
@@peteralexben I will look into that. I would be able to make my own if I do a short stroke . Thank You
Пікірлер: 38