Thank you. I can’t remember where I learned that but it’s not an original idea.
@Cornet_Tooter
Жыл бұрын
@watchrepairtutorials You're welcome. I'm glad you shared it though. It's a great and convenient alternative to the bow.
@gerryodonnell321
Жыл бұрын
Such a great tip. If you come up against a problem, put everything carefully inside a little sealable bag and put it away. Many times you'll go back to it, equipped with better knowledge and tools and sort it. Nothing worse than finding an old project with parts missing
@watchrepairtutorials
Жыл бұрын
Hi Gerry, Many people knew to watch servicing, immediately jump in to his old pocket watches thinking that they should be easy to get running again. Sometimes that’s the case, when you get lucky, but most often they can be extremely challenging. If you haven’t built up your tool set yet or the experience is not there yet. Hopefully they will take that tip and not ruin a piece of history. I’ll see you in the next one.
@chrisjohnson4165
6 ай бұрын
Your videos are phenomenal! I want to dip my toe in the world of watchmaking, but I'm already an expert in another field (or two!) - I must say that your patience in explaining the finer points of this arcane craft is amazing. Bravo!
@watchrepairtutorials
6 ай бұрын
What are your fields of expertise?
@chrisjohnson4165
6 ай бұрын
@@watchrepairtutorials Hi, violin making and previously vintage car repair. I've just got my first watch running, but it's running very fast. Thanks for your great videos!
@watchrepairtutorials
6 ай бұрын
@@chrisjohnson4165 violin making, now that is a skill. Wow.
@chrisjohnson4165
6 ай бұрын
@@watchrepairtutorials Thanks! I went to college as a mature student 32 years ago, and I haven't looked back - a very satisfying job, like yours I guess.
@MyRetroWatches
Жыл бұрын
That was nothing short of phenomenal. I am currently looking for a Jacot tool and now I know what I have to do to use one. Being left handed might be a hindrance but I’m up for a try.
@watchrepairtutorials
Жыл бұрын
Not at all. You would just mount the Jacot tool opposite of the way I had it set up so that the carrier is on the left side of the tool. Then you just need to make sure that you’re burnisher is opposite of the one that I have. They sell them both ways. I will tell you, though that it’s a good idea to practice on some old wheels first. 😜
@notreallyachannel396
Жыл бұрын
I've been waiting for this one! Great content
@watchrepairtutorials
Жыл бұрын
Perfect. I hope everything was clear and concise.
@jjudelson
2 ай бұрын
What a fantastic tutorial on the Jacot Pivot lathe which I am currently trying to become competent at. Your teaching and the way you cover chosen topics is without equal online.
@watchrepairtutorials
2 ай бұрын
Awesome, thank you! How is it working out? Are you using the bow?
@jjudelson
2 ай бұрын
@@watchrepairtutorials I have a bow but now using the identical card retractor set up that you demonstrate and it is perfect. Currently I am using the older version Tour A Pivoter (the one you showed in your video as not to have) although my set is complete. Fortunately however I recently won an eBay auction for a very nice Jacot Lathe that looks to be in great condition.
@watchrepairtutorials
2 ай бұрын
@@jjudelson yeah that card puller is definitely the way to go. I have a bow as well that I made, but I prefer this other method to drive the wheel. When I was taught to use this tool before I was allowed to use it on a customers watch they handed me a box with probably 150 wheels in it and they said "polish these" Every wheel was looked at after I finished it and they said over and over , that's not polished yet, more pressure, more speed until every wheel they looked at was ✨
@jjudelson
2 ай бұрын
@@watchrepairtutorials Sounds like you received first class old world training with high standards that made you the watchmaker that you are. Curious where you received your training?
@watchrepairtutorials
2 ай бұрын
@@jjudelson I went to the Emily Griffith Technical College in Denver CO which at that time had a watchmaking school. This is back in the 80's. Then I apprenticed under an old guy who had come out of the Elgin Watch company for another 8 years. He was a real ball buster, but I learned a lot from him. After that I went t out on my own. I retired almost 3 years ago.
@sonnymoorehouse1941
5 ай бұрын
"In Watchmaking Everything maters" so true Sir !!! fantastic video !!!!!
@watchrepairtutorials
5 ай бұрын
You got that right Sonny!
@tomholloway7566
Жыл бұрын
Alex, what can I say, I’m almost speechless with this video. I kinda understood the need for clean, unbroken jewels and good, clean and polished pivots. You have taken me to a higher level of understanding and on top of that given me a so much better understanding of the Jacot and how to use it correctly. Thank you again for this and all you do, I have never seen or read a better tutorial on the Jacot tool.
@watchrepairtutorials
Жыл бұрын
Well, thank you Tom. A lot of thought went into presenting the Jacot lathe. What questions might come up so I hope I covered everything but we’ll see by the comments. One thing that seem to confuse another fewer is when I was polishing the pivot, and you can see the cord and burnisher moving in the same direction. The way I set up the cord was so that when I pull on it, the barrel and wheel are actually turning towards me so when I push the Burnisher it’s moving in the opposite direction of the rotating pivot. I just wanna make sure that’s clear.
@tomholloway7566
Жыл бұрын
I am sure there are minor things that will come to you afterwards Alex. Having done training for people in the industry/skills that I had a lot of experience in I always found something that I could have put over better or added. That’s part of who we are, striving towards perfection constantly knowing we will never achieve it but can get close. I absolutely see in what you are attempting that is what you are aiming for. Your early videos were really good but you have got them to a much higher level now and I am really grateful for all you do.
@johnvaluk1401
Жыл бұрын
Unbelievable Alex. You are either spying on me or reading my mind. Thanks for the VERY informative video. It has answered many recent questions I have had. With the exception of one. How polish tips of balance wheel pivots along with their effect on amplitude. You got me with this video (patreon) as I believe you provide a wealth of information and your willingness to share. Thank you again.
@watchrepairtutorials
Жыл бұрын
Oh, thank you John to pleasure to have you in our community. That’s a very insightful question. I’m gonna be addressing this in a lot more detail in the video when I look for amplitude, and the escapement. And the short answer is that the ends of the balance staff can also be polished on the Jacot lathe, I just didn’t show it yet. There’s also a hand tool for rounding pivots that I’ll show you. And I believe version also makes a tool specifically for flattening staff pivots. When you take a staff pivot and make it less round that increases the friction in the horizontal position when that pivot is sprinting on it’s end stone. It’s one method used for equalizing to horizontal positions. Interestingly enough, flattening balance, staff pivots is also used to bring horizontal and vertical positions closer together.
@dominiczupo1170
Жыл бұрын
Hi Alex! I live your videos! You are such a great teacher and I have learned quite a lot. Could you possibly do a video about refinishing cases and bracelets, as well as maybe a crystal video?
@watchrepairtutorials
Жыл бұрын
Sure thing! I have some video ideas in the pipeline
@sandorfulop9352
Жыл бұрын
I am impressed again Sir! You are explaining in such a detailed way that the beginner like I am can understand it.
@watchrepairtutorials
Жыл бұрын
Thank you my friend. Let me know if you have any questions.
@douglasskinner
6 ай бұрын
Thanks for the instructions on how to restore a burnisher.
@watchrepairtutorials
6 ай бұрын
Glad to help Mr Skinner.👍
@peterr1342
5 ай бұрын
After watching this vid and getting a jacot for myself i set a task of doing an old pocket watch that was barley running . After discovering that the beds on my lathe wete slightly worn i had to go a few sizes smaller to get the burnisher to contact the pivot but then results happened its now running at 284 amplitude and only a slight change between positions . I think i have a poisong problem though as the beat error increses and decreses between dial up and down . Im stoked with learning the importance of pivots ,all made clear with a microscope (much to my amazment )
@watchrepairtutorials
5 ай бұрын
That’s fantastic, Peter. The Jacot lathe is definitely an investment but makes a huge difference if you’re working on older movements
@crtbang4u
11 ай бұрын
Just started my Watchmaker NOOB journey. Thank you for your expertise and videos. Very very helpful
@watchrepairtutorials
11 ай бұрын
I’m very happy you found my channel. Never hesitate to reach out if you need anything.-Alex
@patrickhauenstein7047
Жыл бұрын
Top quality content as always man
@watchrepairtutorials
Жыл бұрын
Thank you Patrick. More unique content coming down the road.
@normanrehme3836
Жыл бұрын
I also am adding my appreciation for your videos. So well done. The Timegrapher display that has the summary and visual representation of sound, is that a separate machine or something I can find on my 1900?
@watchrepairtutorials
Жыл бұрын
Thank you Norman. No I use the 1900 for quick bench checks. The other is the Etimer escapement analyzer
@-timetowatch1110
Жыл бұрын
Thank you very much, you don't realise how useful your videos are... and what's more, they're free. Thank you, thank you, thank you. I'm really looking forward to the jewels video.
@watchrepairtutorials
Жыл бұрын
My pleasure. I hope you can use this information.
@studniaczasu
Жыл бұрын
Good morning Mr. Alex nice to see and hear you again
@watchrepairtutorials
Жыл бұрын
How are you my friend?
@studniaczasu
Жыл бұрын
@@watchrepairtutorials It's good, although life can be unpredictable. I am learning patiently gaining new skills also thanks to your videos for which I thank you.
@JDRichard
9 ай бұрын
An exceptional video. I found that prior to buying a proper watch cleaning machine. I really had to concentrate on getting the dirt out of the pinion gaps. I’ve also had issues with that teeth usually between the centre wheel and the third wheel
@watchrepairtutorials
9 ай бұрын
Hey JD, how’s it going? Yes those pinion teeth can be a problem spot, especially on those oldies.
@jimmykao3355
Жыл бұрын
Another awesome video Alex. I just purchased a Jacot so this is a very timely video indeed.
@watchrepairtutorials
Жыл бұрын
Perfect, let me know if you have any questions
@WatchWithMike
Жыл бұрын
Excellent Alex! I've learned so much with every video. You rock!
@watchrepairtutorials
Жыл бұрын
Thank you and it’s always great to hear from you Mike. I hope all is well.
@cjfazio3012
11 ай бұрын
Great descriptions in the video! Will check out the rest and then may subscribe if all the others are this good!
@watchrepairtutorials
11 ай бұрын
Welcome aboard!
@rossjackson3670
Жыл бұрын
I knew it would happen, but did not expect it so soon. As a result of playing, watching and listening to you, I now feel I have a good understanding of what you are trying to attain by your tutorials. Even at this early stage of my watchmaking learning cycle, I am able to appreciate the knowledge of working at his level to gain amplitude. I can do most of what you say to do. Putting it into practice is so enjoyable. I'm looking at problems, understanding them and then applying remedies to my level. Thank you. And here's the rub. I have understood the use of the Jacot Pivot lathe and its principle. However financially it is beyond me. Even the cheapest on ebay is a years savings. Ah well! I am however, interested in the distance learning course. Even though I am achieving so much with your video content, I would love to embark training with you. Not sure how the course would run out for me depending on your costing. You mentioned written work, My dyslexia may preclude me. Looking forward to the next instalment of the amplitude saga.
@watchrepairtutorials
Жыл бұрын
Oh Ross, I appreciate your words as always. It gives me a great sense of accomplishment knowing that there are some to get what I’m trying to do. The course will be reasonably priced so that I can cover the expenses in for Vimeo hosting, servers, etc. It will be in the format as some people learn by reading, but there will also be video lectures as well as long and short videos to back up the written word as well, so no matter what your learning style is, I got you covered. I appreciate your hanging out with me, as always, Alex
@rossjackson3670
Жыл бұрын
@@watchrepairtutorials Good man you are. I putting half my weekly spends away. Can't believe how good watchmaking is. Well, especially for me! Aged 75 tomorrow and having the mental ability to learn to repair watches is a boon. Spent time during the lockdown doing and learning various internet based computer courses. All passed to a good level, but to what end when achieved? Can't be employed at my age, and too late to set up work placed venue as cost precludes. Watch making achieves. Something in my hand, Something in my brain. Will never sell the product of my skills. Lots of friendly people out there in the forums, and also in subscribed KZitem sites like yours. Regards, Ross.
@richardhuxford1147
Жыл бұрын
Thanks for the awesome video
@watchrepairtutorials
Жыл бұрын
Thanks for watching!
@WristwatchMedic1953
Жыл бұрын
Great video. I always learn from you. Looking forward to your course. Thank you
@watchrepairtutorials
Жыл бұрын
Thank you Sir. And I hope the videos are helping you in someway.
@etteila7
Жыл бұрын
Thank you for sharing you knowledge, I have learned a lot from you, Alex. Amazing video, I will be waiting the next one!
@watchrepairtutorials
Жыл бұрын
I appreciate that my friend.
@bolgerguide
Жыл бұрын
Another awesome video! You go into such detail to make sure we understand. Looking forward to your 2yr program.
@watchrepairtutorials
Жыл бұрын
Thank you. I try to think of every possible question that one may have and answer it sometimes I miss things but that’s the goal.
@boydsargeant7496
Жыл бұрын
Great vid Alex! I feel I say the same for each video because they are (a good broken record!)! I’m very interested to learn more about the learnings you spoke of. When you service a watch do you do all these processes in one go, or do you do as you have in this series, take it step at a time and go back to get the best amplitude? Obviously pegging is a must do, but do you burnish all pivots in all standard servicing? Looking forward to the next one!
@watchrepairtutorials
Жыл бұрын
When I service a movement, I do all the inspections that I have been covering during the disassembly. On newer movements I typically don’t burnish unless there is an obvious problem but always do it in pocketwatches. It’s always great to hear from Boyd. Thanks as always.
@thegrumpymuso5418
Жыл бұрын
Another excellent video Alex and very timely as I'm battling with not just low amplitude but a variable amplitude on an old Seiko, which are not known for their high amplitude in the first place. Can't wait for the course and hope my old eyes last long enough to get through it.
@watchrepairtutorials
Жыл бұрын
I have a video in the queue that’s gonna be titled something along the lines of “ What makes Seiko run Better at low Amplitude.” I expect it to be eye-opening for many dedicated Seiko fans.
@MyRetroWatches
Жыл бұрын
I’ve now bought a Jacot tool so back again for another visit to this video. My only disappointment is my set although complete is missing the prong thing that holds the spoke of the wheels. I guess I will have to make one somehow but not sure on length or shape. I have plenty of small diameter silver steel so hoping I have a bar with the right diameter. Any tips on replacing these Alex. Thanks 🙏🏻
@watchrepairtutorials
Жыл бұрын
Shoot me an email and I’ll send you over pictures and the measurements from mine
@johnhannon
Жыл бұрын
If it is a Steiner/Horia, They still sell parts.
@jjudelson
2 ай бұрын
And I am sure working all those years in relative seclusion you had no idea that when retired you would reinvent yourself in this new online world to become a bit on a horology celebrity or go to guy. Lucky for all us amateurs/hobbyists trying to learn and improve watchmaking skills.
@watchrepairtutorials
2 ай бұрын
Man, I didn't even know what KZitem was. I was all set for a life of surf fishing a d hanging out with my kids and grandkids. I guess somebody had a different plan for me though .
@TiredGringo
7 ай бұрын
I just purchased a jacot lathe after watching your video, can’t wait to tey this out. it seems theres a mistake on the slide at 21 :26, it should read 0.01 minimum and 0.05 max if i understand your explanations correctly. Just two questions: how do you know a pivot needs burnishîng, and when do you know you burnished it enough and can stop? Thanks Alex!
@watchrepairtutorials
7 ай бұрын
By very close inspection. In all cases with very old watches, pivots will have micro abrasion from running with dried oils and grit. One tell tale sign is when you get larger than normal drops in amplitude when going from horizontal to vertical positions.
@nicholsonsteve2511
Жыл бұрын
Alex, wonderful video. Should the sharp edge of the burnished be polished so as to not scratch the shoulder. Sounds like the burnisher manufacturer let's the watchmaker put his final touches to it.?
@watchrepairtutorials
Жыл бұрын
I keep the sharp ind sharp, it’s not a problem. They are typically usable. I just like to control how aggressive they are so I redo mine.
@gregcapella5941
Жыл бұрын
THANKS
@watchrepairtutorials
Жыл бұрын
You’re welcome Greta
@johntebeau4493
Жыл бұрын
Wow ! I’ve had an old Swiss Jacot tool and a brand new Vallarbe file since 2019. Didn’t understand it enough to use. Could find nothing ‘ period’ on preparing the file. Best, if not the only, instruction I’ve seen on this subject. Many thanks. BTW I read that some pivots with lower quality materials can not stand up to the burnishing procedure?
@watchrepairtutorials
Жыл бұрын
That’s usually when someone says when they break one. You do have to be extremely careful and make sure everything is set up correctly. Because you’re applying force to the pivot, if it’s not flat in the bed, even a quality will break.
@johntebeau4493
Жыл бұрын
Good to know. Thanks for giving a starting point on this. I appreciate your videos and responses to so many questions that come your way. I’m signing up!
@watchrepairtutorials
Жыл бұрын
@@johntebeau4493 awesome. Let me know if you need anything.
@johnspielbauer6432
Жыл бұрын
Alex, great video! Question, as you burnish, are you running the burnisher against the rotation of the pivot or with the rotation? The video looks as though you are pulling/pushing the burnisher with the rotation of the pivot. Thanks again! John
@watchrepairtutorials
Жыл бұрын
It looks weird doesn’t it? The way I set the cord up makes the barrel rotate towards me as I pull the cord. As the barrel and wheel are rotating towards me, I’m pushing the burnisher in the opposite direction of the rotation. So the burnisher and cord are moving in the same direction, but the pivot and burnisher are moving in opposite directions of each other.
@RestorationWatch
Жыл бұрын
Hi Alex, thanks for this and other highly informative videos, and the really helpful posts in forums. I read one great thread you created recently on lubrication. I have one question, do I need to prep my new Bergeon pivot burnisher in the same manner described here, as I've read in a forum question you answered that this is the burnisher you use exclusively.
@watchrepairtutorials
Жыл бұрын
For me the bergeon burnisher is too aggressive. I would imagine that what they’ve done is to try to strike a balance between the needs of a clock maker in the size pivots that they work on versus some of the smaller pivots inside a Mechanical watch movement, whether or not, you decide to dress it down like I did in the video is completely up to you depending on what you work on. If the Jacot lathe you purchased works for you then go for it. I know some of the older ones could be a little problematic when carrying the wheels, but if all the pieces are there, it should be fine. Good luck and let me know if you need any help with it. Also, would love to see a picture of the Lathe. If you have time to email it to me my addresses on the website or in the about me section here.
@amenhotep7704
Жыл бұрын
Gained a new Sub, Thanks to you.
@watchrepairtutorials
Жыл бұрын
Perfect. Appreciate you being here.
@da___man
3 ай бұрын
Great video as always. I was rewatching because I managed to get a great eBay find on a set of 7-8 burnishers. However, they need to be dressed. My purchase also came with a tin plate for polishing. Surprisingly heavy. It has a fine grey powder on it. Possibly diamantine? Any advice on dressing them with the tin plate? Thanks.
@watchrepairtutorials
3 ай бұрын
If you are asking about dressing a burnisher, I didn't in the video
@andriyzhelekh4266
6 ай бұрын
Great video! Maybe it is a silly question but I am going to ask anyway. Is Jacot tool only for pocket watches or it is usable for regular wrist watches as well? Than you
@watchrepairtutorials
6 ай бұрын
It’s suitable for any type of pivot from any type of watch.
@andriyzhelekh4266
6 ай бұрын
@@watchrepairtutorials Thank you!
@davidtrappii1655
Жыл бұрын
Alex! Been watching your vids for sometime now and they are the best. I have a problem and new some help. How would I contact you? Thanks, David
@watchrepairtutorials
Жыл бұрын
My emails on the about me page
@christopherjefferson3561
Жыл бұрын
Hoppe's is great as it won't mess up paint or finishes, has a surfactant and is very low viscosity. One can use a 0w16 oil for burnishing of steel gun parts but preferably one workout detergent which is impossible unless one orders direct from oil companies like Esso/exxonmobil, shell etc. they will sell you (a large amount) of pure 0 viscosity oil sans additives. Otherwise I always use hoppes or a 0w16-20 motor oil ymmw
@watchrepairtutorials
Жыл бұрын
Thanks for the confirmation. I guess great minds think a like.😀
@twsuspensiontech5781
6 ай бұрын
Brilliant video.. I just bought a Jacot tool hoping to polish some pivots on some pocket watch wheels which were 0.5 mm in diameter but my Jacot tool only goes up to 0.45 so the pivots won’t fit inside the centre tool. Is there a different Jacot tool to do pivots of 0.5 mm ?
@watchrepairtutorials
6 ай бұрын
I think most do. I have the Obama-Prazision and it goes up to 1.00 mm. I would sell it and get a different one.
@BokiPetrovic88
Жыл бұрын
Thanks for the video. I have a question about case polishing, do you use polishing machine or you do all of your polishing with pendant motor? Thanks
@watchrepairtutorials
Жыл бұрын
I primarily use a bench machine with felt wheels.
@Supercruze
Жыл бұрын
Alex - Another great video. I would be interested in your guidance on lubrication types and impact on amplitude. I work on a lot of vintage Seiko and these movements depending on calibre tend to run at much lower amplitudes than say most Swiss movements I have worked on. I have worked on ETA 7750 and 2892 which if I recall callsl for HP1300 lubricant on most of the train wheel pivots but I would not dare use that viscosity lubricant on a vintage Seiko train as I fear and have seen much lower amplitude numbers so I tend to stay with a lighter 9010 or HP1000 in most instances. I know the old adage, low speed, high torque (HP1300), high speed, low torque (Moebius 9010). Have a good Memorial Day. John S
@watchrepairtutorials
Жыл бұрын
Thank you John and the same to you. I am by the coast and it looks like we’re going to get rain all weekend so people going to the beach are going to be bummed for sure.
@josetjaycastro4778
26 күн бұрын
Hey Alex, thank you for another full of wisdom and knowledge video that is so incredible helpful for us that are interested in learning more about watchmaking! I have a question about burnishing pivots. Can I use a few watchmaker’s lathe to file and burnish pivots if I don’t own a Jacot tool? I can’t afford one right now, but I recently got a lathe, and I was just wondering if there is a way to do that job on the lathe? Thank you so much for all your help and great videos!
@watchrepairtutorials
26 күн бұрын
The advantage of the Jacot lathe is that the pivot is supported in a bed. Burnishing without this support can lead to the pivot breaking.
@josetjaycastro4778
25 күн бұрын
@@watchrepairtutorials That makes sense! I will be on the lookout for a nice Jacot Tool. Hopefully I can find one a good price! Thanks again Alex! I sure appreciate all your help!
@watchrepairtutorials
25 күн бұрын
@@josetjaycastro4778 it's completely my pleasure.
@samkuong3121
Жыл бұрын
Any recommendations to buy the jewel setting tool and the pinion polishing tool?
@watchrepairtutorials
Жыл бұрын
I’ve heard many good things about the Chinese version of the Horia tool for removing and setting jewels. I believe they’re available for under $300 US. the downside to the tool as far as I know is that there are no Reamers available to make any corrections on the Jewel Hole before inserting the new jewel. I use a Sietz Jeweler so if you can find a complete set, that would be my recommendation. As far as polishing pinions showed using the toothpick and polishing paste and doing it by hand, or you could use any rotary tool with the silicone knife edge disc .
@watchrepairtutorials
Жыл бұрын
✨✨ Get Your Copy of my eBook, The Secrets for Adjusting Watch Rates ✨✨ ➡➡PDF DOWNLOAD watchrepairtutorials.com/ebook/ ⬅⬅ ➡➡Available on Kindle & Soft Cover @ geni.us/4x8C (Amazon) ✨✨Watchmaking Courses and Training ✨✨ ➡➡ watchrepairtutorials.com/watchmaker-course/ ⬅⬅
@mikebruegger8654
Жыл бұрын
Great information. Unfortunate that modern watches are simply replaced or wheels tossed for new ones. Vintage watch work is for real watchmakers only... 😊
@watchrepairtutorials
Жыл бұрын
For the most part like you’re correct as the majority of watchmakers working on movements with available parts can just replace them and that’s what they’ll typically do just because they have to turn and burn, especially if you’re working at a high-volume service center. This is precisely why many watchmakers today either won’t work on pocket watches, or the cost to do this type of work blows people out of the water
@YT-hr3xx
Жыл бұрын
Alex, I want to say Thank You for your videos! They are so useful. Have a question about wheels teeth cleaning- can I use fiberglass brush to clean the teeth? I do this way with dirty wheels. Is a fibreglass safe for teeth surface and geometry?
@watchrepairtutorials
Жыл бұрын
Yes, the fiberglass brushes are fine although I typically roll them through a little bit a rodico.
@GentlemensWatchServices
Жыл бұрын
Along with the details I always get a takeaway from your videos. This time - What matters in watch making? Everything.
@GentlemensWatchServices
Жыл бұрын
Oh! And top work Steve.
@watchrepairtutorials
Жыл бұрын
I appreciate you watching the video and coming away with may be the most valuable lesson you can learn. Everything matters no matter how insignificant it may seem.
@jewhefner3348
Жыл бұрын
Alex, if I’ve broken an incabloc spring on my omega 1120 caliber movement, what should my next course of action be?
@watchrepairtutorials
Жыл бұрын
I did a whole video of sourcing watch parts. kzitem.info/news/bejne/15-nn2GMaqWnaoI This should help
@brianwohlleben3182
3 ай бұрын
What are your thoughts on the eve pin polisher that ive heard reed by several others?
@watchrepairtutorials
3 ай бұрын
They have their place, but they can't replicate what a burnisher does.
@brianwohlleben3182
3 ай бұрын
@@watchrepairtutorials that's kinda what I thought. They are probably ok but not as good?
@watchrepairtutorials
3 ай бұрын
@@brianwohlleben3182 burnishing works by stretching out the metal which fills in low spots which leaves a polished surface. Doing it with an eve would be removing material, which is not ideal for side shake which can cause problems with how the balance runs.
@brianwohlleben3182
3 ай бұрын
@watchrepairtutorials ahh! So eve would be better for light rust or cleaning of an otherwise healthy pivot. But a worn piviot needs to be burnished.
@watchrepairtutorials
3 ай бұрын
@@brianwohlleben3182 well you have to be careful that you don't bend the pivot. I've used them for light polishing inside barrel arbor holes. "Rust be gone" is good for rust removal folllowed by polishing.
Пікірлер: 127