Good video. Thank you. I use Microsoft Movie Maker to trim all my videos. It's free.
@thebomberThebomber-yy2th
Жыл бұрын
Cant i just buy lowered springs like a 3 inch or 4 inch drop rear springs on my 2010 ram crewcab 2wd ? I can still use the stock shocks correct ?
@gruffproductions683
Жыл бұрын
Yeah with that method you will be leveling the truck out however the front may be a little higher. Just a word of caution, when you lower the rear 4” you are basically riding on the bump stops. You may want to get a set of helper bags to smooth out the ride.
@thebomberThebomber-yy2th
Жыл бұрын
@@gruffproductions683 so should i get 2 inch rear springs or 3 inch with rear drop shocks belltech ??
@sergioledesma9127
4 жыл бұрын
How much weight can u carry on the bed with the kit?
@abaddelatorre1440
Жыл бұрын
Do u have to use new lowering shocks or can I run the stocks
@futurestreamz1664
Жыл бұрын
You can run stocks if you want
@harryharrison602
2 жыл бұрын
Did the front ever lower down? Just got mine done an it sits kinda high in the front
@victoralmanza1347
2 жыл бұрын
Did yours go down a little more?
@MrFullforcesound
Жыл бұрын
I noticed on the lot that there was a driveshaft cross member notch that was on the kit. Did you not install that notch kit for the extra clearance of the single driveshaft?
@budsodalsky
3 жыл бұрын
belltech sucks - my truck wont align correctly now
@rodriguezequipment2113
6 ай бұрын
Thanks good video just did my truck too
@christianpalmerin
Жыл бұрын
Is it the same process on an air suspension? I have a 2013 ram 1500 4x4
@lrs333
2 жыл бұрын
Does BellTech provide a kit for air suspension 2016 ram 1500
@gruffproductions683
2 жыл бұрын
None that i found. I actually put together a rear bag system on mine because i was constantly bottoming out.
@fireproof69
Жыл бұрын
Great video. Helped me a ton! Watched it several times before I tackled mine. Went well. I do have a 1/2” difference from side to side. I ordered new spring isolators to go on top of the springs. And will drop and see if I can get it to settle closer to even. Oh… something else about the BellTech progressive spring. The top closer coils are pretty much coil bound sitting empty. And I ended up cutting off the bump stop cups from the frame. Otherwise it was sitting on the newer short stop inserts.
@kevincortez5411
2 жыл бұрын
I have a 18 sport ram 4x4 . Would I be able to cut that spring in the rear to go 6 inch?with out doing any mods
@gruffproductions683
2 жыл бұрын
You would need a few modifications done to go 6”. Once you go past 4” in the rear more things need to be done.
@drakohemi812
3 жыл бұрын
What shocks do you recommend for a 5/8 drop on a 03 ram?
@jonathansanchez6981
3 жыл бұрын
Do you have to jack up the rear axle in order for the shocks to fit they are short about to inches from the axle
@gruffproductions683
3 жыл бұрын
Yes, you have to jack the axle up to seat the springs and line up the shocks
@jonathansanchez6981
3 жыл бұрын
Ok thanks for the teply
@jonathansanchez6981
3 жыл бұрын
Question would you be able give me a call if not to much trouble
@lrs333
2 жыл бұрын
How good does is a ride I hear it puts vibration on the 2 point drive shaft
@gruffproductions683
2 жыл бұрын
For obvious reasons it doesn’t ride as good as stock but its not bad. It also depends on what size wheels you go with. I used the 22” wheels so not much rubber to cushion. I did not have issues with the driveshaft.
@cruzrodriguez8389
2 жыл бұрын
will this kit work on a 2019 classic
@gruffproductions683
2 жыл бұрын
So the kit says up to 2018. However as long as they did not make any changes to the suspension (which i don’t believe they did) it should work. If your suspension looks identical to mine in the video you should be good.
@radiouniquefm
3 жыл бұрын
Good afternoon I have a 2018 bighorn 1500 4x4 myself do you run into any issues after installing this kit on your truck.
@gruffproductions683
3 жыл бұрын
First issue was the alignment shop said they couldn’t fully align it. Some shops don’t like lowered trucks though. I’m getting some offset ball joints just in case. Second, when I ran 20” wheels with the stock tires I bottomed out on the rear suspension a lot. I am in the process of putting air bags in the back. But when I put on my SRT-10 22” wheels with 305/45/22 tires the bottoming out went away. Other than those 2 things the kit works and looks great.
@radiouniquefm
3 жыл бұрын
@@gruffproductions683 thanks for your reply 🙏
@yo_ez1590
2 жыл бұрын
Why didn’t you show you front procces
@yo_ez1590
2 жыл бұрын
Process
@gruffproductions683
2 жыл бұрын
I split it into 2 videos so it was less confusing. You can look the other one up on my channel. Thanks for watching
@jonathansanchez6981
3 жыл бұрын
Also can I install it without the relocation bracket
@gruffproductions683
3 жыл бұрын
You can but i wouldnt recommend it. You will be way out of spec
@josekasino4213
4 жыл бұрын
Is that a belltech relocation bracket?
@gruffproductions683
4 жыл бұрын
Yes, that is the bracket that comes with the kit.
@geezy6141
4 жыл бұрын
Can you tell me the part number?
@gruffproductions683
4 жыл бұрын
Part number for the whole kit for the 4x4 was 965sp
@muko2002
4 жыл бұрын
Make sure to get the relocation brackets by Inez
@gruffproductions683
4 жыл бұрын
I wasn’t having any issues so I decided against getting them. Did you have problems or did you put them on as a precaution?
@muko2002
4 жыл бұрын
Gruff Productions if you notice your differential moved upfront and is not centered anymore . By installing the Inez brackets will help your to center it properly . I haven’t drop mine yet . But I will get it from Moes performance with Viking shocks and the relocation brackets.
@venomous1763
4 жыл бұрын
Are you having any wobble in the rear end at higher speed?
@gruffproductions683
4 жыл бұрын
I’ve only been up to about 95, but no issues with wobble. However it’s basically riding on the rear bump stops so I’m cutting them out and putting in airbags
@jeremiahgiusti294
3 жыл бұрын
Were you able to fix the wobble? Im starting to have the sane issue
Пікірлер: 47