Sir Ben welcome back, anyways what temperature and air flow do you use for cpu removal and reball ? I will like to know so I can follow your timing . Thabks
@terrysong6862
2 жыл бұрын
CPU swap in 45 minutes. Amazing!!
@irepairitall
2 жыл бұрын
Sehr Unterhaltsam und befriedigend zu zu schauen :)
@diyfixtool830
Жыл бұрын
Thank you for your detailed explanation.
@kaiserkhalil1
2 жыл бұрын
Boom…Ben is back to work…Boom ✌️
@RESQREPAIR
2 жыл бұрын
Thanks man 👨
@varmagsmmobilecare2393
2 жыл бұрын
Hi ben I have a doubt If we Lost eprom of any iPhone we can’t fix them But is thare any Alternative solution for that
@RESQREPAIR
2 жыл бұрын
No.
@varmagsmmobilecare2393
2 жыл бұрын
@@RESQREPAIR thank you 😊
@jeedo2013
2 жыл бұрын
Nice my friend.. you are the best , so i need ask you about your soldring tip what is it number model??
@mirceaalicu
2 жыл бұрын
Impressive 😍 What temp are you using when cleaning the CPU for your hot air station? Is it advisable to use a hot jig for cpu when cleaning it? The specs of the jig mention it's thermostat 220 - 240 degrees. Is it too much for A13?
@sivasankarganeshp4990
2 жыл бұрын
Hi ben Most video see you open phone display, folder stand a round tool what tool this Name???
@kanawbo7399
2 жыл бұрын
thank you your job it’s very good
@wernerbrokmann5761
2 жыл бұрын
Super wie immer
@RESQREPAIR
2 жыл бұрын
Danke Dir ☺️
@jonpura1520
2 жыл бұрын
sir ben.. what is the brand of your hot air station the one you use to put tha cpu?
@PoorTechAnger
2 жыл бұрын
what bga paste are you using sir? thanks
@ezeigwechidozie827
21 сағат бұрын
Well done boss please what kind of rework station are you using the one you are using to clean the cpu
@KyleGP
2 жыл бұрын
What hot air station do you use?
@gtrichard89
2 жыл бұрын
iphone 11 need bottom board for touch? i thought touch is on upper board only.
@RESQREPAIR
2 жыл бұрын
Touch works fine, device ready.
@azewho
2 жыл бұрын
Are you recruiting or training students
@Neeraj_kumar
2 жыл бұрын
Awesome 😎😎😎
@maharoofm1653
2 жыл бұрын
Great👍
@arnoldclex7845
2 жыл бұрын
please What tool do you use to scrape glue off cpu? thank you
@MrSkar87
2 жыл бұрын
toothpick
@maharoofm1653
2 жыл бұрын
How to temp &air quick 861d hot air ‘ben sir
@RESQREPAIR
2 жыл бұрын
500 / Full air.
@sportchannel122
2 жыл бұрын
NICE
@RESQREPAIR
2 жыл бұрын
Thanks 🙏
@mohasinuddin376
2 жыл бұрын
Osam sir
@yourtech7
2 жыл бұрын
🔥🔥🔥🔥
@RESQREPAIR
2 жыл бұрын
Thanks 🙏
@carlosuyat9105
Жыл бұрын
looks like a pencil in removing the glue on the cpu
@directsystems2225
2 жыл бұрын
English please 🥺
@RESQREPAIR
2 жыл бұрын
It’s English and German like always.
@alicidaci2787
4 ай бұрын
What temperature do you use to heat the CPU and how much air do you use? Can you share the temperature values with us?
@praphaukarraaj4754
2 жыл бұрын
Master ben what soldering flux are u using? Pls answer
@RESQREPAIR
2 жыл бұрын
Amtech NC-559 V2. Original from amtech USA.
@almatarim77
2 жыл бұрын
Where do you work, my friend, in which country do you work? I am from Yemen, I follow you a lot and love your content
@RESQREPAIR
2 жыл бұрын
Germany 🇩🇪
@AntonioWengratt
2 жыл бұрын
I always got amazed by you methods/process. If you allow me to ask, I've noticed that you constantly get your air station out of the CPU while cleaning. This is to maintain the CPU safe, without too much heat? I ask because I'm starting with training this, and always at the end my cpu end showing o short, problably because I overheat it too much to clean, or even because my pratical only allows me to get the perfect reball after 5, 6 attempts lol. Thanks!
@greenkawasaki1
2 жыл бұрын
was soll das ganze kosten ? auch möglich bei einem iphone 5 ? Lg
@MahmoudAhmed-vm7hl
Жыл бұрын
Good work bro but touch should work with out button board .thanks
Пікірлер: 52