Thank you very much for the excellent video presentation. Yes, you are right, the sensor produces AC voltage, so which pins to connect makes no difference.
@asarcik
Жыл бұрын
mine Crank sensor connector V is 2.38 but manual seys ; Measure the voltage between the 5V reference circuit and the chassis. = 4,8~5,2 V Measure the voltage between the CKP signal circuit and chassis. = 4,8~5,2 V is any vrong? or what ?
@jlsetnuper
Жыл бұрын
thanks for watching...nothing wrong with the crank sensor
@paulfoldes3873
Жыл бұрын
excellent video thanks what kind of scope you are using
@markim5087
Жыл бұрын
I don’t get why your not talking and explaining what your doing and looking for as your volume works, lol..I was a tech for 30yrs and taught auto electronics at UT , explaining in detail works better for those who don’t really get why sin wave your looking for.. on your oscilloscope
@paulfoldes3873
Жыл бұрын
why can you connect crank censor to directly to osciloscope dso 188
@jlsetnuper
Жыл бұрын
for bench testing, yes you can..because two wire sensor is magnetized and can produce its own voltage with metal..but you cannot do this with 3 wire sensor, you need a 5 volt bias voltage to work on oscilloscope..thanks for watching..
@dwightjtaylor
4 жыл бұрын
A revealing demonstration of an applied application.
@pakiengr.896
3 жыл бұрын
Whole KZitem no body knows..location of crank sensor on k6 Engine
@meassavuth4649
11 ай бұрын
* Thank you very much sir , your video is very helpful, very important for any beginner repair man , and please show how to test oxygen sensor too , because i have look many other videos but it can not make me understand it , only your video can make me understand quickly , thanks
@jlsetnuper
11 ай бұрын
Noted...thanks for viewing
@matthewjuergens9183
Жыл бұрын
That's really cool. That little oscilloscope is awesome.
@jlsetnuper
Жыл бұрын
thank you..
@randymccalla9995
2 жыл бұрын
Didn't notice, but did it ever output higher than 3.2 volts ?
@ronr7753
2 жыл бұрын
i use analog meters when doing these test
@globalcommerce7654
3 жыл бұрын
Very good and excellent video! you are skilled!
@jlsetnuper
3 жыл бұрын
thank you for your comment..
@nisri1567
3 жыл бұрын
Good job! It could habe been more interesting,if you could tell or show us, the pins of the Cam sensor. And during the test, what was at the two pins of the sensor connected? Power? How much? Or your volt meter prongs. Was the flat piece of metal a magnet? What was the minimum rpm of the machine. Thank you too.
@jlsetnuper
3 жыл бұрын
the cam sensor produces a sine wave signal , so AC voltmeter probes can be connected either side of the pins..the piece of metal is a flat bar iron , cam sensor itself is magnetize..and the drill was set to 1 with a maximum rpm of 600. and the video shows that lower rpm produces lower voltage and high rpm with higher voltage on a good sensor..thanks for watching
@nisri1567
3 жыл бұрын
@@jlsetnuper you are really appreciated. Thank soo much for your polite and satisfatory informative soon reply.
@titanchelito741
3 жыл бұрын
Hola entonces ese sensor está en buen estado ? O está dañado? Esta bueno ? O esta dañado?
@jlsetnuper
3 жыл бұрын
este es un buen sensor ... gracias por mirar
@pavel7311
3 жыл бұрын
hi where does he get to buy that oscilloscope
@jlsetnuper
3 жыл бұрын
you can buy it on ebay, just search for "oscilloscope DSO188" ... thanks for viewing
@rassieetchells5879
3 жыл бұрын
Hi. Is that a normal piece of metal plate that you use to check the voltage
@jlsetnuper
3 жыл бұрын
It's a piece of metal that will attract magnet.. thanks for viewing
@ozriblit
3 жыл бұрын
A piece of steel. I use an angle bracket because it is nearby.
@jinglethrushmusic2478
3 жыл бұрын
Good job.. can l use the same method on a 3 wire crank sensor?
@jlsetnuper
3 жыл бұрын
yes, you need to know the pin out of the 3 wire sensor, you need to have a supply of 5 volt and the third wire to the multimeter or oscilloscope.
@jinglethrushmusic2478
3 жыл бұрын
Ok thanks 😊
@vidrioandsonstrucking2422
2 жыл бұрын
mi sensor marca 513ohms entonses esta malo? espero me conteste gracias
@jlsetnuper
2 жыл бұрын
hola, depende de la temperatura del sensor, si esta caliente tiene baja resistencia, si esta frio tiene alta resistencia..va de 300 - 2000 ohms..
@vidrioandsonstrucking2422
2 жыл бұрын
@@jlsetnuperok gracias
@mohamedfiraz7041
2 жыл бұрын
If this sensor wire is bad will the car starts ?
@jlsetnuper
2 жыл бұрын
If sensor wire is bad the sensor will not work..and the car will not start..thanks for watching
@kennydoolarchan9515
2 жыл бұрын
@@jlsetnuper What is the name of the small oscilloscope? Where can I buy the Oscilloscope?
@jlsetnuper
2 жыл бұрын
@@kennydoolarchan9515 you can buy it on ebay, search for oscilloscope DSO 188.
Пікірлер: 37