Yes. I have seen other channels review the HFT "pipe bender" (pipe kinker). They have mainly all said the same thing. That type of pipe bender is worthless without the use of SAND.
@todds5956
9 ай бұрын
What wall and diameter pipe you got there? Thanks
@StevenPenny
2 жыл бұрын
Interesting. I was debating on getting a better bender but it looks like that one might do the trick. Have you ever used a better one? Like a Rogue or JD2?
@AndersenAdventures21
2 жыл бұрын
I own a rogue. I will be buying a jd2 next. I would personally got with the hydraulic jd2 over the rogue. I’ll do a video on the rogue at some point. Just been to busy lately
@StevenPenny
2 жыл бұрын
@@AndersenAdventures21 Gotcha. I mainly want to create a roof rack and bed rack for my hmmwv so it’s more of a one time project for me. Hopefully I can get away with using the HF one, I’d hate to buy a $1k+ unit mainly just for one project.
@correria5
3 жыл бұрын
good night you have to put sand in the tube and because my tube is all over, putting sand resolves it friend.
@JuanMartinez-ie6gv
2 жыл бұрын
Nice thanks.
@notthatdigusted7468
3 жыл бұрын
How do you set this bender up with the hydraulic oil? I just got mine and when I move the lever nothing happens. How do you lower the pump after you bent the pipe?
@AndersenAdventures21
3 жыл бұрын
There is a twist valve on the bottom. I just pull on the pipe on mine and force it back down.
@tracnunya7165
2 жыл бұрын
good vid, i need to bend 2 inch exhaust into u shapes for my fireplace, what bender is this, the 12 or 20 ton ?
@tracnunya7165
2 жыл бұрын
i mean 12 or 16 ton
@AndersenAdventures21
2 жыл бұрын
16 ton
@jameshisself9324
Жыл бұрын
I figured sand would do the trick. Excellent demo, well done.
@raymundocruz4550
3 жыл бұрын
Me gusta..
@firmerom
2 жыл бұрын
Great video, i try whit sand but not work how you 😢
@AndersenAdventures21
2 жыл бұрын
I found it works best on 1-1/4” pipe. Make sure you are using pipe and not tubing.
@firmerom
2 жыл бұрын
@@AndersenAdventures21 i us the same pipe, 1.25 shedule 40
@AndersenAdventures21
2 жыл бұрын
@@firmerom you may try adjusting your pins and heat the pipe. Maybe even grease. I am not sure what else I can help with. I have since upgraded to a rogue fab bender.
@firmerom
2 жыл бұрын
@@AndersenAdventures21 did you use any kind of special sand?
@manueliganciocarvajalperez9341
2 жыл бұрын
de cuanto es el espesor del tubo??
@jamesrussell2936
Жыл бұрын
Schedule 40 es un estandar en EUA para espesors del tubos. En este exemple el tubo es 1 1/4" (o 31.75 mm), y el espesor es cerca 3.5 mm.
@gerardopena303
2 жыл бұрын
1-1/4 schedule 40?
@AndersenAdventures21
2 жыл бұрын
Yea
@thrillbillyjp1
4 жыл бұрын
Hey bro I've tried this with bunch of wasted tube so far
@AndersenAdventures21
4 жыл бұрын
Are you using tubing or pipe ?
@Bromagen25uploader
4 жыл бұрын
@@AndersenAdventures21 Just curious would it not work with tubing?
@AndersenAdventures21
4 жыл бұрын
Bromagen25uploader No. tubing is a different diameter, these harbor freight benders are for pipe only.
@pinkporcelain
4 жыл бұрын
James on there site it says tube or pipe 🤷♂️
@AndersenAdventures21
4 жыл бұрын
barbie ang . Pipe and tubing diameters Are different, pipe is Inside diameter. And tubing is out side diameter. The Dies in these harbor freight benders are designed for sch 40 or sch 80. Not tubing.
@queenqutie9236
3 жыл бұрын
Get sand from the beach
@AndersenAdventures21
3 жыл бұрын
Yea you can do that.. I just didn’t want salt water in the inside of the steel pipes
Пікірлер: 37