@@blackcellagent yes, sturdy and holds the shells tight, no complaints so far
@blackcellagent
3 жыл бұрын
@@1sonjohn44 Awesome! Thank you for letting me know! 🙂
@claytonwhitman1608
3 жыл бұрын
I have one on order already, glad to see this review.
@shaunstayfree5551
3 жыл бұрын
Smart move, enjoy it!
@vicenteandrew4393
3 жыл бұрын
Sorry to be offtopic but does anybody know a trick to get back into an instagram account?? I was stupid forgot my account password. I love any assistance you can offer me.
@parkergriffin4388
3 жыл бұрын
@Vicente Andrew Instablaster :)
@rocketstar9067
3 жыл бұрын
I have that same one but it will mot work with my B&T forehand , The B&T forehand will not go back all the way it hits the side saddle to soon. But the B&T does work with the stock Picatinny. Because there is a grove on the stock Picatinny that lets the B&T slide back all the way, i am now trying to find a side saddle that will work with my B&T
@PARR53
3 жыл бұрын
Definitely getting one of these for my Panzer Arms M4.
@loganback9224
3 жыл бұрын
Be a lot cooler if it was a Benelli
@n.silent.w
2 жыл бұрын
Very Nice
@elonmusk8667
2 жыл бұрын
1:48 use this protection or else there will be wear marks.
@DTreatz
Жыл бұрын
Now they just need one for the Beretta 1301
@shaunstayfree5551
Жыл бұрын
Amen brother
@Big_Lex
3 жыл бұрын
Just ordered mine can’t fucking wait
@shaunstayfree5551
3 жыл бұрын
great choice. Mine is broken in now and I love it more
@gitarman666
3 жыл бұрын
Did you get it? I’m deciding between the 6 and the 8 Does the 8 feel too big? Just from the pic it seems to go into the trigger well Although I’m sure it doesn’t affect operation
@shaunstayfree5551
3 жыл бұрын
@@gitarman666 it does not protrude or interfere with the trigger well at all. The m4 is already heavy, 2 extra rounds no biggie IMO. If you are more weight sensitive 6 may be advisable. Id rather have two extra rounds accessible is why I went with 8
@gitarman666
3 жыл бұрын
@@shaunstayfree5551 Thanks bro, yeah 8 sounds good
@chezdusa5767
3 жыл бұрын
Shudnt the brass go down...way quicker to remove to load
@tjjensen173
3 жыл бұрын
Isn’t the rubberized pad supposed to go behind the side piece that holds the shells? To protect the side finish of the receiver?
@shaunstayfree5551
3 жыл бұрын
Timothy Jensen nope, on the m4 there is a gap between the receiver and the shell carrier; so they don’t touch unless the support is damaged or bent. With certain shotguns it may be necessary but not on the m4
@Was-here2
3 жыл бұрын
Yes it does
@gitarman666
3 жыл бұрын
Just got mine, yeah the gasket is even notched for the existing screws but it’s optional to protect the finish “ according to the manual” I would think most new rails wouldn’t be coming off but I’m throwing mine on
@jkees6751
2 жыл бұрын
I believe you are correct. My initial impression was the same as in the video at first, I thought you had to cut it to fit the top under the rail but then I realized that it's actually for the side so the shell holder side doesn't have a gap and possibly make metal on metal contact with the side of the receiver if bumped. The adhesive back rubber gasket material even have holes/cuts that match up perfectly with the side screws on the part that houses the elastomer.
@lordofentropy
Жыл бұрын
Yeah it's 100% for the side. It's notched perfectly to still allow access to the screws on the back of the shell carrier to be removed to replace the rubber tubing inside that holds the shells in.
@Xxtictoc1216xX
3 жыл бұрын
I really want them to stock the side saddle for the benelli super nova but there out everywhere and the company hasn’t gotten back with me by email. This is like one of the main things I want for my shotgunnnnn
@shaunstayfree5551
3 жыл бұрын
They have good customer service, but everyone in the industry is slammed right now. Try calling next week, hopefully they can more directly give you an ETA rather than waiting for them to go through tons of emails.
@istiaqueahmedkhan1690
3 жыл бұрын
Looks like they're too tight. in an emergency situation, will it cause any problems? Please give us a range video next time.
@bigvaxmeanie925
3 жыл бұрын
I have one and they are tight enough they won't wiggle out. I highly recommend it
@magaman3048
3 жыл бұрын
Your receiver is blue like the one I bought in 2020. I bought a second one this year and it’s black. I’m a little disappointed with Benelli for putting out these blue receivers.
@shaunstayfree5551
3 жыл бұрын
Yes certainly blue. I have emailed Benelli. They gave a non-descript answer saying because of military production there is color drift during anodizing.... I am getting a new M2 sent to my FFL, I am curious to see what the "color drift" will look like there
@magaman3048
3 жыл бұрын
@@shaunstayfree5551 I’ve read that too and I call BS on Benelli for that. I’ve never seen BLUE color drift on the military contract hard anodizing for the AR15, M16, or M4 carbine, Beretta 92, M249 or Benelli M1014 for that matter .
@shaunstayfree5551
3 жыл бұрын
@@magaman3048 typical eyetalian, ey yoouza wanna shatgan, yoouza take it anda lyke it, huh! No questiones!
@magaman3048
3 жыл бұрын
@@shaunstayfree5551 I prefer the whimsical Nintendo portrayal of Italians better. “It’s a mea, Mario! Thank you so much for a buying mya shotgun. Have some a ravioli!”
@shaunstayfree5551
3 жыл бұрын
@@magaman3048 haha, hilarious and correct
@M-D751
2 жыл бұрын
Hi, can you leave the shells in the side saddle during extended periods of time or will the side saddle start warping?
@shaunstayfree5551
2 жыл бұрын
It’s metal, it won’t warp. Thanks for watching
@Luis-be9mi
3 жыл бұрын
would you recommend using loctite thread locker on the screws?
@shaunstayfree5551
3 жыл бұрын
I do not because they were not thread locked from the factory, with decent but not too much torque it should be fine. I have shot several rounds and no issues.
@carguy...
2 жыл бұрын
For the life of me I cannot get the screws out on top of the rail to install this even with a heated screwdriver, I killing the original screws???
@shaunstayfree5551
2 жыл бұрын
Are you the original owner? If not previous owner may have used red thread lock. Is it an original benelli or a clone? If clone, same issue. Temperature sensitive thread locker requires you to hit the correct temp to break open the bond. Try using a heat gun.
@sergebastion4626
2 жыл бұрын
Dood you need to buy a set of gun smithing screwdriver!
@shaunstayfree5551
2 жыл бұрын
You’re correct. Let me see what’s out there. Thanks for the suggestion
@El_Taco72
2 жыл бұрын
Does the top rail sit down onto the receiver about the same as the original?
@shaunstayfree5551
2 жыл бұрын
Yes it does.
@gitarman666
3 жыл бұрын
Is it in the way of the trigger assembly removal pin?
@shaunstayfree5551
3 жыл бұрын
Nope
@jaymanjay1030
2 жыл бұрын
Meh! I'm going with shell cards. You'll be fighting to feed your shotgun and your side saddle, when I can simply rip off the empty card and replace it with another, and two cards fit in a mag pouch. That looks hard to put shells in and take them out. Those are going the way of the dodo
@shaunstayfree5551
2 жыл бұрын
Yep, what works for your needs and what you will train with is always the best choice.
@jerseyboy8017
2 жыл бұрын
I really like the look of this but I think I’m going w 7 cartridge cards and Velcro for ease of use. But again I like this look for sure. Maybe this on the receiver w Velcro card on stock?!
@headspace8282
3 жыл бұрын
Do you think it might scratch the side finish on the gun?
@shaunstayfree5551
3 жыл бұрын
HeadSpace no it won’t, because it does not touch the side of the receiver.
@project86xero
3 жыл бұрын
So has the carrier come loose at all? If not how many rounds have you put through it?
@shaunstayfree5551
3 жыл бұрын
About 125 rounds with several 3in magnum loads. There is a torque spec in the manual as well
@project86xero
3 жыл бұрын
@@shaunstayfree5551 I know. 15 inch pounds. I was just curious because I have the exactly same carrier. Honestly I'm more curious to see the long term effects on the reciever. Five tiny screws with all that weight under shotgun levels of recoil. Just has me thinking a Esstac velcro carrier might have been better for the gun in the long haul.
@shaunstayfree5551
3 жыл бұрын
@@project86xero well for me the bigger concern is the very positive retention takes some force to get the shells out, the Velcro I think would be quicker for SD use vs target practice, although there is a trade off there as well as Velcro can also come undone or move around etc
@project86xero
3 жыл бұрын
@@shaunstayfree5551the advantage of the velcro is thats its easy to remove the card when it's empty and swap it with another. Also a 7 shell card is the same size ad an AR 15 mag. So you can use the same chest rigs or plate carriers. You can also use a velcro belt or bag liner too. Also the velcro esstac cards hold shells more securely than the mesa carrier with the lighter retention tube. It's about the same as the heavy duty ine to me. Plus when they ware out a replacement is $15.
@shaunstayfree5551
3 жыл бұрын
@@project86xero good points and hard to beat but I always thought I would get it to hang up on something or otherwise F it up in a self def situtation. The Mesa is sturdy and aint going nowheres, but for a target gun the estac sounds stellar
@robertvonneurath6720
3 жыл бұрын
anyone knows if this is good for the Canuck Operator???
@shaunstayfree5551
3 жыл бұрын
I think there is a good chance it will but I can’t be 100% certain. Please try emailing or calling Mesa tactical
@COVID...19
2 жыл бұрын
Do you or anyone know if this works for the M4 H2O?
@shaunstayfree5551
2 жыл бұрын
Yes it will. There is no difference with H20 I am aware of other than the finish.
Пікірлер: 68