I can’t believe how rough you were with the lamp after removal, dropping it is something I would never want to do. But then you opened it up and touched the globe… wow.
@RickMeetsWorld
Ай бұрын
Hi my tk800 keeps over heating but everything is clean. Quick question should the fan next to the lamp be blowing inwards or outwards? Mine is blowing outwards the one closest to the gold base of the lamp. Thanks❤
@minseokkim909
2 жыл бұрын
New cooling fan is DC12V, 0.22A. But, still getting Fan 2 error. I want to know the cooling fan spec of TK800. What kind of fan did you use?
@neerajs75
2 жыл бұрын
For people looking for information in fan part numbers. Inlet fan in my TK800 unit is Delta AUB0912HJ-00 12V 0.5A 9cm (90mm) size and outlet fan is Sunon MF92251V3-1D010-G99 again DC12V 92x92x25 in mm in term of size. Both are DC Brushless 3 wire fans.
@deviantv1ral
2 жыл бұрын
I have a tk800m I’m wondering if it’s the same. Also wondering if can use noctua fans to quiet it a bit
@vdross
8 ай бұрын
@@deviantv1ral have you tried?
@DawidPretki-ek2qk
3 ай бұрын
Have the same model. Tell me if it worked for you !@@deviantv1ral
@duguesebastien4620
6 ай бұрын
Bonjour j'ai un soucis avec ce modèle. Il me met défaut porte ouverte.pouvez vous m'aider?
@luckyb4538
2 жыл бұрын
My fans never kick on. Projector will work sometimes but till temp out quick. Motherboard issue? I smell a slight burn as well
@claudialemos8782
Жыл бұрын
What is the fan model ?
@TeaWhyTwo
2 жыл бұрын
Hi sir, my BenQ tk800m projector is loosing color. I replaced the lamp but the problem persist. Do you have any advice on what I should do next? Is it the color wheel? Everything else works and the projector stays on. Thank you
@neerajs75
2 жыл бұрын
I got into the same problem. Root cause was dust on the colour wheel sensor. Working fine for last 1 week since I cleaned the sensor on the colour wheel assembly PCB.
@sahumks
Жыл бұрын
@@neerajs75 what is the difficulty level to open the color wheel sensor to clean it? do i have to remove the top PCB board to access it?
@neerajs75
Жыл бұрын
@@sahumks yes top PCB and almost entire assembly will has to be removed as cables etc are connected to PCB. Take pictures while disassembly keep track of screws etc. If you do it in a peaceful environment with enough time at hand it should be doable with basic tools.
@minseokkim909
2 жыл бұрын
Hi sir Have a question. Fan 2 error keeps appearing after replacing the cooling fan. Maybe it's because the cooling fan is different. What is cooling fan model No.?
@computergearstudio
2 жыл бұрын
Can you give me a picture of your new and old fan with connector pin
@neerajs75
2 жыл бұрын
My tk800 lamp not turning on so no display. Lamp LED blinks orange then becomes red and then power goes back to orange (standby). Was working fine and lamp usage is only around 500 hours. One day powered it up ams there was no display. Any idea what may have gone wrong. ?
@computergearstudio
2 жыл бұрын
Are you a technician?
@neerajs75
2 жыл бұрын
@@computergearstudio yes I have electronics engineering background. opened cleaned fans and plugged out cables and reinserted and in few hours now it all started working. Thanks for your response.
Пікірлер: 21