One additional benefit to the wifi antenna vs the one for the Pi is that you can run this in metal cases without massively degrading the wifi signal. That can be important if you want to use a metal case for passive cooling to improve performance and you want to use wifi. This can be useful for klipper and server farms as well since you can put this internal to the 3D printer and still have the wifi be usable. Overall it's a thoughtful addition.
@stephank1965
Жыл бұрын
I am very happy with this Pi. Works absolutely perfect
@JohnKlopp
Жыл бұрын
Good content and clear explanation. Board looks very promising. Subscribed!
@StackingLayers
Жыл бұрын
Thanks and welcome
@Paulo_Araos
Жыл бұрын
Thank you very much for the review... I bought this board to try it out but I still have doubts about the canbus... according to what I saw, it takes away usb ports that you know about this topic... I would appreciate some information since I haven't found much
@barkxd
Жыл бұрын
Damn I didn't even realize you were such a small channel take my sub lol
@StackingLayers
Жыл бұрын
Haha yeah, just a small fry for now. 😁 Thanks for the sub!
@TheButchersbLock
Жыл бұрын
I have no idea why you have so little subscribers, the information on this and the canbus video is brilliant. I am a complete noob when it comes these btt pi’s and klipper. Is there something I need to do to run more then one Logitech c270 at once. I have tried the second and third camera in different ports etc, but 2 won’t work at once. Oh and that case is great I am going to buy it now 👍🇦🇺😊
@StackingLayers
Жыл бұрын
The 2 camera thing is a bit weird and I have the same trouble with a raspberry pi. If you haven't done it yet you'll need to set the second camera [cam 2] with port: 8081 and the device: with something like /dev/video2 or /dev/video3, you can also instead use the device id found with, ls /dev/v4l/by-id/* But I've still had an issue with only one camera showing. I think it could be network speed causing it because I've seen others say it starts working with the Ethernet cable used instead of wifi.
@PedroGomes_27
8 ай бұрын
I have a question, when flashing from raspberry pi imager what board should I chose?
@StackingLayers
8 ай бұрын
None, the board options are for raspberry pi boards.
@Cptnbond
Жыл бұрын
Amazing case you have designed. Where can I purchase these boards?
@StackingLayers
Жыл бұрын
Thanks! They are on AliExpress www.aliexpress.com/i/1005005500181519.html And BIQU/Bigtreetech's site biqu.equipment/products/bigtreetech-btt-pi-v1-2 Not affiliated.
@crckdns
Жыл бұрын
When did you make that video? The stock is full pretty everywhere for pi4 Only the price went about 10€ higher than before the shortage with 73€ for a 4GB version. (Way too high) But good to know that there are alternatives! Only the 1GB ram isn't much for media center and some other stuff. Same with 100mbit eth, this should be upgraded. You've deserved my sub!
@StackingLayers
Жыл бұрын
Yeah the stocks are finally starting to build up luckily. Still near impossible to get in my area and there's no way I'll support the scalpers. Thanks for the sub!😊
@RichmondHBK
Жыл бұрын
What does this Pi actually do? It seems to me that all it does is install Klipper firmware to your printers main board? Isn’t there other ways to install the firmware. If it replaces a Raspberry Pi then does it run Octoprint because that’s all I ever used my Pi for as my Ender installs firmware directly from MicroSD? Is it an alternative to Octoprint?
@StackingLayers
Жыл бұрын
It's a full Linux computer just like a raspberry pi is. It can run Octoprint, but It is not exclusive to 3d printing. It's an alternative option to raspberry pi.
@RichmondHBK
Жыл бұрын
@@StackingLayers That image you installed was Mainsail? BTT Pi is made mostly for Mainsail?
@PterPmntaM
Жыл бұрын
Great dude, do you know how configurate the fan pin correctly?
como puedo hacer para que no demore tanto en encender , a veces duro hasta 10min y no lo reconoce aun el sistema
@StackingLayers
10 ай бұрын
Sorry, I've never experienced that. If it has never connected then I would recommend to double check that you have the correct WiFi SSID and password. If it has connected and randomly does this then it seems like something isn't working correctly. You can try to update with, sudo apt-get update && sudo apt-get upgrade -y
@kamertonaudiophileplayer847
Жыл бұрын
It looks interesting, however it is under powered for my use.
@V843v3r
Жыл бұрын
ask BTT to send you samples instead of buying your own
@StackingLayers
Жыл бұрын
I get some occasionally 😊 but also buy when I can.
@Marc42
Жыл бұрын
Nice video, well done! Joined the #first500subsClub 😎
@StackingLayers
Жыл бұрын
Thanks for the sub! It's fun to see the numbers going up, and admittedly a bit surprising 😅 I'm glad it seems my videos are being helpful.
@TheFeralEngineer
Жыл бұрын
good review video. would've liked to see the tft35spi working as i only use hdmi screens. I'm gonna shoot you an email
@str133-pu6mt
Жыл бұрын
greetings I recently bought microprobe v1.2, but although I set the clipper, it occasionally gives an error, can you help me if you have a discord account?
Пікірлер: 29