Just tried this method on a neglected family "heirloom" rifle that probably hadn't been cleaned or oiled in 50 or 60 years. Works as advertised! I'm impressed. The barrel had obvious rusty spots in the bore that defied removal and I could never get a clean patch even after an hour of cleaning. Thanks for the tip!
@MosinVirus
3 жыл бұрын
My pleasure. I am glad it helped.
@randyc5650
8 жыл бұрын
I used Frontier 45 to clean some of my guns rusted from sitting under water for 3 or 4 weeks from hurricane Katrina. It did a great job on the bores and also the severely rusted exteriors. Thanks for the video.
@MosinVirus
8 жыл бұрын
+Randy C Glad I could help.
@bobsunkees3392
4 жыл бұрын
@@MosinVirus thank you for sharing the details I will try it on my own mosin PS have you put a scope mount on one of the mosins ?
@MosinVirus
4 жыл бұрын
@@bobsunkees3392 yes, a while ago. I used a mount and base from Accumounts.
@Nattleby
8 жыл бұрын
I call it the "Stalingrad" layer....
@MosinVirus
8 жыл бұрын
Lol
@pinkeye00
7 жыл бұрын
heh
@harriscaelo2303
5 жыл бұрын
🤣🤣🤣
@GodWasAnAlien
4 жыл бұрын
I'm imagining you saying this in the voice of Nikita Khruschev, as depicted in Enemy at the Gates XD
@gin91652
9 жыл бұрын
After watching this video I ordered some. Holy cow! Was I impressed. I have two milsurps that I've cleaned and cleaned, but the bore was still dark and I had simply accepted the fact that I wasn't going to get them to look very good. Then I tried this method. The bores on both rifles look virtually new now! I can't wait to get them to the range to see how much it improves accuracy. My daughter used some to clean the rusty spokes on her 1996 motorcycle that she's restoring. It worked very quickly and shined up everything she used it on. Now I need to order more! Thanks very much for posting this helpful video!
@MosinVirus
9 жыл бұрын
My pleasure. Glad I could help. Thank you for watching.
@alexb.6466
9 жыл бұрын
Thanks again! I will try shooting it and see. The rifling looks good. I spent $325 for it at a small local gunshop. I hope it was not a foolish investment but it looked pretty interesting and I had to have it.😊
@MosinVirus
9 жыл бұрын
+Alex Beda Depending on the gun you got, it may or may not be a great deal, but overall, I think $325 is not bad for just about anything other than Mosins. Definitely try shooting, and even if you never get a clean patch out of the bore, don't worry, it is not a problem. Simply make sure to remove the loose debris and oil well, then wipe dry before shooting.
@FinalFront
2 жыл бұрын
Man I wish I had been more interested in firearms 6+ years ago. I'd love to be able to get a decent Russian capture Kar98k without having to pay $1200 - $1500 for it.
@keithlerminiaux1365
5 жыл бұрын
The big 45 metal cleaner works wonders . Also used some J & B bore cleaning compound. Very pleased with the results. Thanks!
@MosinVirus
5 жыл бұрын
Very nice. I agree, that cleaner is just awesome
@bfgivmfith
2 ай бұрын
I subscribed to your channel awhile back because of how easy and thorough you are to learn from. Thank you for the Frontier Big 45 metal cleaner advice. Luckily, I have saved my worn-down brushes. I thought for smaller calibers, but this is perfect! I have been struggling with a MAS 49/56 bore, but I think this might do the trick! Thank you again!
@MosinVirus
2 ай бұрын
My pleasure. I am glad I could help.
@30roundclipazine79
6 жыл бұрын
6:30, you're welcome. Btw I use a copper choreboy in the same manner. Copper will not scratch your bore. It dies a great job removing leading.
@MosinVirus
6 жыл бұрын
Thank you again.
@rogervancouwenberghe6685
Жыл бұрын
I used very tight fitting Choreboy, on what I thought was a rusted bore, but I checked it with a neodyum magnet to make sure it was copper and not copper plated steel. It worked, removing hard deposits that I had thought needed to be honed out. The bore is now very serviceable and shiny clean, though with some pitting that I can live with. 👍
@danielgrove7782
Ай бұрын
No way! I would love to know what this stuff is...i don't really need it now but good to know it works
@Brent0331
9 жыл бұрын
Thanks brother, just cleaned an old Yugo 8mm M53 barrel using your trick and it turned out great. Thanks for you help!
@MosinVirus
9 жыл бұрын
No problem. Glad to help.
@srdjan272able
3 жыл бұрын
I will try the same
@slimintx2890
9 жыл бұрын
Appreciate your sharing your experience. Just watched your bluing videos and made it look easy enough I think I can do it. An old fellow at a neat gun shop gave me a ball of this Big 45 Frontier Cleaner when I asked him what to use on surface rust. I haven't used it yet but appreciate your endorsement and use of it. I just got a Mosin that turns out is about as pristine as they come according to my gunsmith who has five of them. It wasn't caked in cosmoline and recommended using paraffin (wax) oil and a cloth to clean it up. Don't know if you've tried that but would like to hear. He said it's not as harsh on the metal. I 'm also getting an old FN Hi Power that has a lot of rust covering and some pitting on the slide but excellent mechanical condition and bore. I'm hoping Big 45 can help with that. Thinking about using your bluing technique on it but don't want to mess too much with it or the Mosin. Like the look of them as is pretty muc. Like an old timer once told me years ago, "It's not how old a gun is. It's how good it shoots." Keep up the good work and sharing.
@MosinVirus
9 жыл бұрын
Thank you so much for watching. I think you will like it. The cleaner safely shaves off rust without hurting bluing. You can also use various gun solvents when using the cleaner to aid in removing stuff that shouldn't be there.
@Nossucram
Ай бұрын
First time i have been so desperate to save a barrel and just bought this product instantly. My kar98k from 1942 has very dirty patches
@MosinVirus
Ай бұрын
@@Nossucram the product works.
@Nossucram
21 күн бұрын
@@MosinVirus i put the threads on a used brush and used my drill to run through it. I did (brush-wipe)x6 times, and its the first time in ages i can see reflection of light in the barrel. Its not mirror clear but its no longer rust brown, so yeah this surely is better than the brass brush. Cant wait to test it at the range, last time the devation was 1-2 feet in any direction from where you aimed.
@MosinVirus
21 күн бұрын
@Nossucram if your bore was already eaten away enough it may not change anything regarding deviation. But will make it easier to clean after.
@justinian420
7 ай бұрын
Thanks for posting this. I'm gonna try this on a filthy M95 Mannlicher I'm getting ready for sale
@MosinVirus
7 ай бұрын
It should work
@jim778
8 жыл бұрын
I have a Swiss military rifle that I traded an old friend for years ago. I became obsessed in cleaning this rifle. What I did was place it on my table in a gun holder and ran patches thru it 1-2 times a day saturated in Shooters Choice cleaning fluid. It took 6 months until it became clean. Now patches come out spotless today if I clean it. I tried for years cleaning it but it wasn't until later in my life I just decided to try cleaning it like this and for this long but it did clean out and the bore now looks like new and shines like a mirror. At first the green would run out of it as green as grass. I think that was from the copper being broken down by the cleaning fluid.
@MosinVirus
8 жыл бұрын
good to know. I believe the Swiss used grease to clean their bores and rifles in general. I have so far seen very few swiss rifles with bad bores. of course the ones I was getting are not too old (K11, k31)
@joshuahenderson
2 жыл бұрын
Very excited to try this out, and hopefully based on the comments. Just got a 1916 Spanish Mauser and after so much cleaning just couldn’t get the bore clean. Going to try this next.
@MosinVirus
2 жыл бұрын
Definitely give it a try. It does work.
@justinmaxwell4925
7 ай бұрын
10 years later, I’m going to try this. Lol just ordered it so I’ll try to remember to come back and update this after trying it on my Kar98.
@MosinVirus
7 ай бұрын
It should work. There are a few comments here that show people trying it out.
@benkanobe7500
3 жыл бұрын
Thank You. I have four Mosins, 3 Tula, and one Izy. One (I will not name the very popular reseller) said: "Bright and shinney bore" (the Izy). That rifle was like from a different century compared to my three Tulas all manufactured in the 30s. The bore is black. NOT bright, not shinney. I spent numerous hours on each Tula to get a non-black bore. All three shot amazingly accurate to 100 yards (which is all I can see these days at 64 years old). I want to try this method on the Izy and see what happens. The Seller was a complete lie as the three Tulas (which had black bores were "cleaner" than the Izy these folks sold me). I will get back to you with the results after I try your recommended methods.
@MosinVirus
3 жыл бұрын
Please do.
@josephkoziol5421
10 ай бұрын
Thanks for the informative and helpful posting. I have ordered the Big 45 Frontier Metal Cleaner.
@MosinVirus
10 ай бұрын
My pleasure. I am sure you will be impressed, just like I was.
@josephkoziol5421
5 ай бұрын
@@MosinVirus I was very impressed. I am am really pleased with how this method/product cleaned up the barrel of my K98 Mauser.
@jarodcrazyindian
5 ай бұрын
You can see that some of the patches were used, but not all. Im thinking he has more and possibly he is pleased about it. Worms could be trained to inspect the bore, which would be my guess.
@MosinVirus
5 ай бұрын
The product does work.
@jarodcrazyindian
5 ай бұрын
@MosinVirus I was just being silly, but I actually did purchase 4 of the pads from the website. They're only $6 each.
@AFishBicycle
3 жыл бұрын
Gonna try this on a pawn shop 30/06 I got for my nephew
@Toolness1
Жыл бұрын
I use a chore boy scrubber for the same purpose, works well. Just wrap slivers of it around a tired bronze bore brush. Wipeout foaming bore cleaner is great stuff, but pretty harsh.
@MosinVirus
Жыл бұрын
Sounds great!
@charli0072003
10 жыл бұрын
All your videos are actually very good, I guess you will become a great youtube guy soon Regards from Spain and excuse my poor english
@MosinVirus
10 жыл бұрын
Your English is great. Thank you for watching my video. And I hope I can someday become a great KZitem guy, so I will keep trying.
@Cesko_Plny_Fialovejch_Zmrdu
2 жыл бұрын
Well you say "actually" as it's surprising
@charli0072003
2 жыл бұрын
@@Cesko_Plny_Fialovejch_Zmrdu This was 7 years ago...
@jamestompkins7928
2 жыл бұрын
Soak the bore with Ed's red bore solvent that you can make yourself! Let it soak in the bore for 30 minutes to an hour then give it a good scribbling with a bronze brush!
@MosinVirus
2 жыл бұрын
Yes, that is also effective. I am just saying that this method seems to work pretty good.
@Space.Ghost.
8 жыл бұрын
I've used Whisk rust remover with pretty good results. I take off all the wood first, not sure if drips or spills will hurt it but my stocks are immaculate. never thought to use this method thanks for the tips! beautiful k98 also
@MosinVirus
8 жыл бұрын
Thank you.
@kencammenga4442
6 жыл бұрын
I have used pure copper scouring pads (Chore Boy) for years. Use a magnet to make sure they aren't just copper colored.
@MosinVirus
6 жыл бұрын
Ahhh, yes, that was the product other viewers were mentioning. Sounds like it works well too. But does it leave copper deposits?
@ratagris21
7 ай бұрын
Blue wonder and a bronze phosphate brush does wonders on a surplus barrel. Takes the rust, carbon, snd lead fowling all in one effort. Folow up with a CLP patch and you be good to go. Removes surface rust with 0000 steel wool.
@MosinVirus
7 ай бұрын
You should make a video demonstration. And I mean it seriously.
@av3nger3
9 жыл бұрын
FP-10 for the win. Plus Clenzoil and some U.S. GI Bore Cleaner
@66ECHO
5 жыл бұрын
Old video yes. But helpful to me & I bought the product for my 2 Mosin Nagant rifles
@MosinVirus
5 жыл бұрын
I am glad the video helps. The product makes cleaning bores easy
@brushwolf
Жыл бұрын
Can we all agree that is a really nice k98.
@MosinVirus
Жыл бұрын
It is.
@charlesblair1216
9 жыл бұрын
A good cleaner I used on a old 30_06 Midland barrel bore is Wipe Out foam. The rifle was not grouping properly and after the cleaning with Wipe Out it is dead on from a cold bore. A good follow up with G96 or Rem Oil to clean out all the foam and finish with dry patches.
@MosinVirus
9 жыл бұрын
Thank you. I have used that foam before. it works pretty well.
@620brown
10 жыл бұрын
Thank you for this video.
@davidberry7534
3 жыл бұрын
Works like a charm thanks for the tip, used it for cleaning my mauser m48 , next is the mosin nagant
@MosinVirus
3 жыл бұрын
Excellent!
@hansvonmannschaft9062
5 жыл бұрын
You know it's been a terrible day and you should've finished watching the video the following morning when you begin wondering what's up with that 40mm Bofors shell standing there between the patches and bronze bristle brush somewhere around minute 10:20. Thanks for the video though, fine gent, gonna be using this method this very same weekend on my 1891 Argentine cavalry carbine :-)
@MosinVirus
5 жыл бұрын
I think you will find that the product does help get the bore cleaner sooner
@hansvonmannschaft9062
5 жыл бұрын
@@MosinVirus Indeed! thanks so much! Done with the carbine, but still got two 29" Mausers and a 16" Marlin Camp 9 to clean and I definitely got no excuses now haha :-) The idea about adding the product to the bristle brush was genius, and don't worry, I bet lots of folks accidentaly ignored the insert. For example, when you buy a Desert Eagle pistol, you get an insert amongst the ton of advertising and stuff that explains how to properly handle the gun in order to avoid all malfunctions. I saw absolutely no reviews making mention of such an instruction set, and plenty of messages all over the web on how unreliable the DE is. Well... there you go... not sure if I'd blame the users in a 100%, because those pointers should be in the manual, not a leaflet. Anyway, thanks again for the video! Saved it to "watch later" by the way, 'cause it's the only way I found of bookmarking them. Have a great day!
@danclas5983
4 жыл бұрын
Great for removing leading from a barrel quickly too .
@MosinVirus
4 жыл бұрын
Absolutely true.
@MegaBait1616
7 жыл бұрын
i bought a 2-pack cause of this video. not cause of rust but to "get the lead out" and It's Works !!!! just like you said. the pack goes a long way for deleading barrel's. i have beautiful Finnish Sako 1942 M-39 that looks new. has a new bbl. that they did when refurbished after the war that i bought from Classic. although it's new bbl. couldn't get out all the cosmoline lands n groves well this stuff is amazing. i also did all my families other barrels too. even revolvers that shoots cast lead rounds like my first hand gun 1974 S&W Model 10 blued and i can now see all the rifling. with blued guns you don't want to use harsh chem.'s on them. i have a .308 Savage model 11 which is a great rifle with a Boyds thumb hole stock that i shoot FMJ and didn't think it was leaded well i was wrong now it shoots 1-1/2" groups at 100yd.'s. i don't use "big 45" everytime but maybe every 6-8 months . it works !!!!!!!!!!!! thanks again. buy it on ebay it's cheaper with free shipping too.
@MegaBait1616
7 жыл бұрын
BTW, i use "Sweets 7.62" bore cleaner too. another great deleader n copper remover.
@MosinVirus
7 жыл бұрын
MegaBait56 Glad I could help. the cleaner works beautifully, right?
@MegaBait1616
7 жыл бұрын
yup, truly does get the bores shinny. but also cleans out the grooves real well. it is not just S.S. coils either cause it seems softer? but if you do what you said with an old brush it pulls out the copper, lead, carbon easily without hurting any rifling. then the patches get cleaner n cleaner. good call.
@lilaNilla
Жыл бұрын
I have a original no. 4 mk 1 * lee enfield and I’ve been just trying to find anything close to help me figure out if my headspace and bore is fine. Seems ok but I just wanna make sure I don’t blow up after I fix it. Recommendation?
@MosinVirus
Жыл бұрын
You can try and get the go/no go gauges.
@lilaNilla
Жыл бұрын
Thank you for the reply!
@jacksonthompson7099
Жыл бұрын
The SAAMI field gauges on a lee Enfield are 70 thou VS the British military field gauge at 74 thou. Take your bolt head off the bolt and see if the threaded end is below the long bolt lug that runs almost the whole length of the bolt. If below flush (threaded hole where your bolt head threads in) you will probably crack cases, worst case scenario is gas out of the chamber (Personal experience with a Savage No4 mk1* using HXP 303) but your rifle has built in fail safety features to not catastrophically fail. I've never seen a lee Enfield receiver that popped like a mauser or a M1903 where the whole top of the receiver was gone. A little quick method i've found is when have the bolt closed, look thru the gas vent hole on the receiver. If your bolt head covers a quarter to half of that gas hole your probably fine, another method I also discovered is with the action closed take a flash light and point it at the chamber/bolt head area on the action then look thru the gas escape hole and see if you see light/daylight. If you do then your probably in trouble. I will make note that when building the rifles at the factory the british had only 2 gauges a 64 thou GO and a 74 thou NO GO, your rifle could have been built from the factory to have a headspace of 72 or 73 thou, as long as it ate a 64 gauge and NOT the 74 gauge then the rifle was in proper tolerances. Bloke on the range has done 2 videos on what to look for when "getting" a lee enfield rifle when it comes to bedding and such for the No1 and No4 rifles. I'll try and link the vids for you.
@@lilaNilla kzitem.info/news/bejne/laSIvKZqn6ZiqoY Really nice vid on discussing the Lee Enfield, I wanted to add that the flash light and gas hole method are things i've found in my Lee Enfields that work due to the experinces of my No4 Mk1* Savage, gas/burned powder smoke would leak from the action while still closed and above the case head where the case thins out to form the walls would have a pretty noticeable crack as well which rendered the pieces of brass useless for reloading. The solution is a new old stock Lee Enfield bolt if out of tolerances, no one makes large Lee Enfield bolt heads anymore unless you stalk the internet for large bolt head which i've only seen 3 times pop up in 10 years that measured to 0.637 inches which is typically a number 3 bolt head, yes bolt heads can be swapped to be back in spec but the bolt head isn't wearing down, its the bolt itself which should be fitted by a gunsmith AND a special proof load has to be used after proper fitting your new bolt to the action, the reason why is because the special proof load will help mate as much locking surface on the bolt lugs to the mortises on the receiver. Lee Enfield rifles are rather complicated to build and are not a straight forward process. A pretty knowledgeable gunsmith/armorer would be building the rifles/repairing them.
@jonatham35
10 жыл бұрын
I need to get some of that stuff! I tried never dull on my Mosin, but that didn't work. Kept getting dirty patches. Will give this stuff a try. Thanks for the video!
@MosinVirus
10 жыл бұрын
I have tried the never dull stuff too. I tried many things, but nothing worked as well as the Big 45 Frontier. I couldn't believe that no one had posted a video on this product used to clean bores before.
@Hezigrimm
5 жыл бұрын
Will be trying this on my Finnish m24. The gun is in tremendous condition considering its age, just some light pitting in the bore. I have used most of my pads trying to clean it.
@MosinVirus
5 жыл бұрын
It will work wonderfully
@alexb.6466
9 жыл бұрын
Thanks, I am watching more of your other videos and learning a great deal. Also just Subscribed.
@MosinVirus
9 жыл бұрын
Thank you. I hope to not disappoint with my other videos. In advance, forgive the many "ok's" during some of the earlier ones... Lol.
@marckcarbonelloifveteran410
3 жыл бұрын
Apply Carburator cleaner through the barrel and see you later rust, Then run the bore patches through the barrel and all the crud will come out.
@MosinVirus
3 жыл бұрын
Thank you. I will try it.
@scarter176
2 жыл бұрын
I will give this a try. Thank you my friend.
@MosinVirus
2 жыл бұрын
My pleasure. That "wad" basically shaves lead off the bore. But doesn't touch steel.
@donkeziah2564
6 жыл бұрын
Try using WD-40 or something similar in the bore and on a bronze brush to soak and scrub the bore. Patch out on occasion. When satisfied carbon is removed, dry the bore and saturate the bore and a nylon brush to coat the bore evenly with a copper remover and let it set as most copper removers are chemical action rather than mechanical. Use a nylon brush so the copper remover will not be dissolving a bronze brush and giving you a false indication of more copper. Change the brand of copper remover on occasion for better results. I think you will be pleased with the results.
@MosinVirus
6 жыл бұрын
Thank you. I will try your method, but this actually works really well.
@fedreserv6133
Ай бұрын
OK, so what exactly makes the difference-chemicals you use, or dishwashing steel you've put on the rod?
@MosinVirus
Ай бұрын
@@fedreserv6133 the material seems to be making the most difference.
@spadetrump
5 жыл бұрын
Today I used a worn down brush wrapped in 0000 steel wool with jb bore paste and kroil. Took corrosive ammo damage down quite a lot. I was really not expecting it to get it as smooth as it did. Those specks wouldn't come out with normal hours long cleaning...
@MosinVirus
5 жыл бұрын
Glad it worked out for you.
@spadetrump
5 жыл бұрын
Just test-fired and my group sizes have been cut in half. Bore looks great after 15 rounds.
@MosinVirus
5 жыл бұрын
@@spadetrump excellent.
@spadetrump
5 жыл бұрын
Well. I am a HAPPY MAN!! just handloaded 45.5 gr Varget and speer 150 .311 and shot a 1" 4 shot group at 50 yards. wow. I was getting ready to sell the gun. just got it last week for $300 with a spam can of ammo and accessories. the bore had corrosive damage but the pits seemed to not really be there more like corrosion sticking out not craters. initially shot 6-8" groups with surplus ammo. then tried some PPU and got it down to 4-5" cleaned it up with steel wool and its down to 3" at 50 yards. handloads are king. 1"! writing this load down in my books! thanks for the idea and saving my rifle!
@MosinVirus
5 жыл бұрын
@@spadetrump glad I could help.
@brycealthoff8092
3 жыл бұрын
May just try this on an old muzzleloader I picked up
@XxBlacKkNighTxX7
2 жыл бұрын
Ordered some of that Frontier wool. Hopefully it will come in clutch. My mosin ever since i got it 4 yrs ago or 5 the pitch black fouling has never ended (i do shoot it) im tired of it and want to see patches come out clean for once and keep it that way after i shoot.
@MosinVirus
2 жыл бұрын
That cleaner should be able to do something about that. Good luck.
@DMX-PAT
4 жыл бұрын
The metal/alloy Frontier Foil stuff works well, it doesn't scratch up or ruin the bore... that's amazing!! When you did all the barrels that were really dirty did it remove all the fowling?
@MosinVirus
4 жыл бұрын
Yes, it works better than anything else for fouling. But it will not reach into pitting obviously.
@dmithsmith5880
6 жыл бұрын
A awesome way I came up with to hone out a bad pitted rifled barrel and make it almost new. Remove barrel from the rifle and strip any parts from the barrel. Dry brush the barrel really well to remove heavy rust and garbage and rinse well with chlorine free brake cleaner and swab with a clean mop, this will remove any left over grease/oils. Plug the muzzle end of the barrel and fill with evaporust rust dissolver. Let sit over night then pour it back into the bottle. Rinse barrel with hot soapy water and rinse with hot water, swab dry. Mop a good coat of Rem oil or similar into the barrel. Tape the muzzle end of the barrel shut and mix up a batch of clear poly type pourable epoxy resin, stand rifle up muzzle down and pour enough resin down the barrel to fill from the bottom up about 3 inches or so, let cure When dry pound the epoxy slug out with a wooden dowel, you now have a exact fit honing tool for your bore. Trim both ends of the slug square with a saw. Bevel one end of the slug about 3/16" on a 45deg angle all the way around with sand paper, this will be the leading edge of the honing slug. Purchase a tube of course cut steel polishing compound, apply to the mouth of the barrel and slug, push slug bevel end first through the barrel repeatedly until desired hone is achieved. The bevel on the front is to allow the compound to force it's way between the slug and barrel. You can also mix aluminum oxide of desired grit directly into the epoxy making a slug with built in abrasive qualities. I have made barrels that were damn near garbage look like almost new using this process. Warning: do not skip the oiling step before pouring epoxy into the barrel or it will be really hard to remove
@MosinVirus
6 жыл бұрын
Sounds interesting but I would worry about opening up the bore diameter.
@dmithsmith5880
6 жыл бұрын
@@MosinVirus It all depends on the grit you use and how many passes you take with it. I use this process more on antique cap and ball muzzle loaders with horrific barrels where it really doesnt matter much, you just run a thicker patch or cast the next size bigger round ball. But even with modern smokeless a bad barrel is a bad barrel, so even loosening the bore a touch and having a smooth rifling and a clean smooth bore is still better then a crusty barnacle filled barrel any day. It does work extremely well though, even using a little fine lapping compound will make a fouled leaded barrel shine like it just came off the shelf.
@spadetrump
5 жыл бұрын
I just got this Frontier 45 from ebay for $7. previously had good results with 0000 steel wool. tried it tonight on a pitted Mauser. same results as the steel wool but much faster. seems to have better abrasion. wont harm the bore. looks great!
@MosinVirus
5 жыл бұрын
Yes, it appears that the shape of the strands will shave and scrape softer materials off steel faster.
@spadetrump
5 жыл бұрын
testing accuracy today after using frontier 45. 1" groups from all 4 bullets at 50 yards! Speer 180 31 cal. Midway repackaged blem 180 spitzer, PPU 174 FMJ BT and PPU 180 SP BT. 42 grain Varget s&B primers and the same 4 cases half neck sized brass on its 20+ firing (PPU)! all these are currently on sale at midway.
@MosinVirus
5 жыл бұрын
@@spadetrump very impressive
@schneidersreptiles843
6 ай бұрын
0000 grit steel wole should do the same thing Seen it done on outside rust spots On the barrel
@MosinVirus
6 ай бұрын
Thank you.
@SteveVi0lence
2 жыл бұрын
The same happens every time I wipe... I wipe and wipe and wipe and still crud
@davidfriesen9512
3 жыл бұрын
I wonder if pouring boiling water down the muzzle might really loosen things up.
@MosinVirus
3 жыл бұрын
Won't do much to lead deposits.
@chewies9456
8 жыл бұрын
If you want shiny, put some mothers mag and aluminum polish on a patch and run it through a few times followed by a thorough cleaning. I damn near blinded my self after doing this for my mosin, the bore was bright as hell. There's no shine like mothers =)
@MosinVirus
8 жыл бұрын
Thank you. I wasn't going for shine. merely cleanliness. with pitted bores, they tend to load up a bit more. and become more difficult to clean, so this gentle shaving off lead and carbon method seems to work.
@chewies9456
8 жыл бұрын
I understand, I used some 00 steel wool drenched in hoppes or my first pass on my mosin, followed by a shit ton of dirty patches, then I experimented with the mothers polish and was blown away by the crud it pulled out after I had just pulled a pure white patch out. If you do try it, use very little because it's a paste and will make a mess.
@MosinVirus
8 жыл бұрын
+Chewie S thanks. will check it out.
@aaronwirepa3209
4 жыл бұрын
What is the green fluid you're using?
@MosinVirus
4 жыл бұрын
If it was froglube I wouldnt recommend it.
@jorqlip
6 жыл бұрын
Have you tried polishing the bore and if so it would make a nice video
@MosinVirus
6 жыл бұрын
I generally dont polish bores. Reason being is that if you try to polish down to the level of pitting the bore diameter will change. The firearm at that point will lose accuracy. I think of it the same way as polishing any metal. If you try to polish out scratches or pitting you are removing material.
@Yustax
4 жыл бұрын
Loved your video and I definitely will try this method with my BYF 41. BTW. I am also trying to look for a good cleaning rod. Who makes the rod that you're using in the video? And what size is it? Thank you.
@MosinVirus
4 жыл бұрын
I don't remember the brand, but at this time I am using carbon fiber rods, one for shotguns (thick rod that works for larger calibers) and one for smaller calibers including .22lr. I thick they are both about 40" long. I also use bore snakes.
@josel1948
8 жыл бұрын
Have you ever thought to use a rod guide? It is very convenient.
@MosinVirus
8 жыл бұрын
Yes I actually have one. Still don't use it all that much, just on my higher quality bores
@mistergrendel32
2 жыл бұрын
What was the second bore liquid you were using to clean the bore? 🤔 That Big .45 Frontier product looks great. I should try some.
@MosinVirus
2 жыл бұрын
Sorry, that was when I still used FrogLube. That was the second liquid I used. Currently I still use Hoppe's bore gel, and to lubricate and oil i use ballistol or Lucas oil when I need it to be a little less runny.
@ryanjohn8035
5 жыл бұрын
I have a 29 hex receiver that I will try this on. I believe it had pitting when I got it. However I only recently noticed it.
@MosinVirus
5 жыл бұрын
If there is rust this method will remove it.
@cecilandrews7479
20 күн бұрын
Unless you're part owl I have to use lights will not clean or work on my rifle
@comradeamerican4393
8 жыл бұрын
what about a 124 year old shotgun thats in good condition except a littel rust in the bores please help
@MosinVirus
8 жыл бұрын
The same thing can be used. It shaves rust off.
@zacharyroach1990
7 жыл бұрын
i neglected to clean my mauser bore for way too long and it ended up as you say, packed. needless to say I am still trying to make it clean. I let the bore soak for a day in gun slick solvent and it did not even come close to finishing the job.
@MosinVirus
7 жыл бұрын
zachary roach definitely try this stuff and follow up with JB bore cleaning compound.
@zacharyroach1990
7 жыл бұрын
definitely, it was so dirty that it was causing an over pressure condition with ammo that I had fired previously without issue.
@khemib
6 жыл бұрын
I found a mosin with a bullet loaded in it. I would say it was in pretty good condition once I had removed and polished the metal and wood. However, I've never cleaned the bore. By the looks, it looks quite pitted but the pattern and groove (sry not an expert!) look sharp and deep. Should I use the same method? And is there any cheap cleaning kit (brush with rod) that you could recommend? Thanks!
@MosinVirus
6 жыл бұрын
This method just gets the bore cleaner faster. It would not remove stuff out of pitting, but it is actually better to keep pitting loaded up. The cheapest way I think woukd be to get a bore snake. For rods I prefer carbon fiber rods.
@beggottenson1869
4 жыл бұрын
Just purchased it, just making sure lol will it remove the blueing on my mosin
@MosinVirus
4 жыл бұрын
It should not, unless you rub the bluing with it too hard and too long.
@slick777go
3 жыл бұрын
Speaking of , I picked up a Cva Optima 50cal on the cheap.. its been stored for few years with powder and sabbot in it. "No Primer" ! The breech plug is good removable and not rusted and the rest of the gun is really nice shape,, but the BORE is like old dried rusty.. I removed breech plug and tried pushing from nozzle to clear it even gave some fiber hammer taps on the rod. I used a 243 brass casing to fill the void. To know avail I haven't put any solvent in the bore or attempted to clean it , wondering if I should just tie a string to trigger " or would that score the bore more . Any good advice appreciated
@MosinVirus
3 жыл бұрын
I vote oil down the bore and let it sit.
@slick777go
3 жыл бұрын
@@MosinVirus Thanks I removed the plug and sprayed the powder real good with ballistol and also down the bore, now it sits muzzle up leaking some rust out. Also sprayed with a mixture of ballistol and distilled water.
@TimoFilipek
8 ай бұрын
Hi I clean my Mosin and Kar 98k with ballistol. Is it there some difference than doing it with the hoppes you used in the video? I use primarly ballistol, in past I used some special bore solvents like BoreTech, etc. but I got rid of it and I stay only with Ballistol because I heard the special bore solvents could damage the bore
@MosinVirus
8 ай бұрын
Use whatever works for you. I prefer Hoppe's Bore Gel for cleaning and Lucas gun oil or Ballistol for lubrication.
@TimoFilipek
8 ай бұрын
@@MosinVirus okay, many people recommended me only ballistol, few of them recommended different solvents, so I made an avarage of that more people recommended only ballistol so I use it.
@MosinVirus
8 ай бұрын
@@TimoFilipek I generally agree, Ballistol works well. And it is generally safe for most finishes. But I start coughing from the smell.
@TimoFilipek
8 ай бұрын
@@MosinVirus heheh yeah, it smells really badly xDD
@MosinVirus
8 ай бұрын
@@TimoFilipek some people really like the smell. Once it sits for a bit on the gun and most of it fumes off, I don't mind it either. But during cleaning it is a whole other story.
@GodWasAnAlien
6 жыл бұрын
Bought an Aero Precision barrel about 4 months ago. Opened it up, made sure everything looked ok, packed it back up. Finally put a rifle together with it last week, look down the bore, and its got a coat of rust through most of the barrel. What should I do? Is this even normal for a new barrel? I didn't even think about lubing it up when I got it, thought every barrel came greased up from the factory. Never had a round fired through it.
@MosinVirus
6 жыл бұрын
I would use an oiled patch to remove the rust. Then I would grease it up for storage.
@GodWasAnAlien
6 жыл бұрын
Yeah I already used up all my patches trying to get the rust out. The last one I had was still pretty black upon exiting the barrel. I just sent Aero a disgruntled complaint, that's really not cool, IMO. If they had oiled that properly from the factory it should be good for at least 6 months sitting in plastic in a box on a shelf. Had a lot of metal shavings coming out of the barrel too, more than I would consider normal from machining stragglers. Kinda seems like they forgot a couple steps.
@MosinVirus
6 жыл бұрын
@@GodWasAnAlien in that case I would probably send it back to them.
@Deergringo
5 жыл бұрын
@@GodWasAnAlien Definitely send back, likely a bad batch
@GodWasAnAlien
5 жыл бұрын
Yeah bruh. So check this out. Before I sent it back I made a snide remark about how the barrel seemed to have all the properties of 416 stainless instead of CrMoV like I ordered, wonder what'd happen if I tested it. They still RMA'ed it with a dimple in it, and the one they sent me is clearly a different material. Most likely actually 4150 this time. Lighter, more of a dull gun metal finish, and the rifling wasn't as deep.
@afterburnerUSAF
8 жыл бұрын
Is it safe to fire a rifle with a dark barrel?
@MosinVirus
8 жыл бұрын
as long as the bore is not obstructed, and proper caliber rounds are used, should be safe.
@johnnybarbar7435
8 жыл бұрын
Pull the bolt stop/ejector back and tuck a folded patch under the lever to hold it out of the way while cleaning the bore.
@MosinVirus
8 жыл бұрын
Thank you. Excellent suggestion
@jmartin9059
7 жыл бұрын
Your metal wrapped brush is a good way to scrub out metal and powder fouling. AND, You might consider LAPPING the bore with a mild abrasive paste such as JB Bore compound, which is currently a Brownell's product. ...If you cannot get this in your country automotive valve grinding paste can be used. This will remove impact imbedded fouling...and smooth out the machining or tooling marks inside the barrel... This "should" have been done when the barrel was new... but, BORE LAPPING late is better than never. "Kroil" (or possibly substitute Ballistol or Frog lube) on the tight fitting bore mop first with lapping compound slathered over the top... 20 to 40 passes through should be enough to "lap" the bore... Then clean, as you normally would, to get the abrasive paste out and oil with Ballistol, Frog lube , Kroil or your favourite gun oil. Additional cleaning of fouled bore after firing many rounds with same process and fewer strokes may improve accuracy lost to fouling. As accuracy degrades over time with numerous rounds fired you will know when to clean and lap again.
@MosinVirus
7 жыл бұрын
J Martin thank you. I have used bore lapping past before. the only thing I don't know about is if repeated use can eventually open the bore up.
@CharlesMartellus
10 жыл бұрын
Did you notice any drop off in accuracy after using the product?
@MosinVirus
10 жыл бұрын
I have not. But I don't have any high precision rifles to really verify. My rifles seem to perform the same, but are much easier to clean.
@boarzwid1002
2 жыл бұрын
You should make a wooden chamber protector to protect the chamber
@MosinVirus
2 жыл бұрын
I had a plastic one. Both ends, muzzle and chamber. Didn't use for the video.
@boarzwid1002
2 жыл бұрын
MosinVirus 👍
@jonaskvass1589
8 жыл бұрын
You have probably never seen Mausers or Mosins guns bores from polish Lodz Film Center.... Cleaning such ones is a challenge!
@MosinVirus
8 жыл бұрын
I bet.
@taterjones5544
2 жыл бұрын
Zero demonstration of cleaning a rusted bore. I cant tell you how much this helped me because it didnt.
@MosinVirus
2 жыл бұрын
Sorry it didn't work out for you.
@EvanSmith4211
9 жыл бұрын
i used a similar method to this using steel wool instead, worked prety good.
@MosinVirus
9 жыл бұрын
With this thing you don't have to worry about taking any steel off your bore.
@squishybadger8704
8 жыл бұрын
my M53 have a very disgusting bore. and here i'm trying to clean it
@alexb.6466
9 жыл бұрын
So this bore will never get mirror like shine correct? It looked clean, but not shiny with light pitting, just like my sportarized Brazilian Mauser 1908 I just purchased. I was very disappointed when I couldn't get the bore to shine like my other surplus rifles. I will try your brush method, but guns with this kind of bore is safe and accurate in your opinion?
@MosinVirus
9 жыл бұрын
the pitted bore will never shine. They are perfectly safe to shoot. they simply load up a lot quicker. I have quite a few bores in this condition and some outshoot my bright and shiny bores.
@alexb.6466
9 жыл бұрын
Thanks.
@bcshooterfmjprime7540
8 жыл бұрын
+MosinVirus when I first got into shooting I cleaned religiously and FREAKED when I'd see surface rust then would clean like mad. I live in the always wet north west and have accepted surface rust as it never seems to affect my shot. but for anyone who doesnt want to order anything. nothing beats a hot clean. heat the barrel up with firing then clean. repeat until rust is gone.
@MosinVirus
8 жыл бұрын
+Wes Jensen thank you.
@bcshooterfmjprime7540
8 жыл бұрын
+MosinVirus also. one of the best shooters I have is a 115 year old winchester 30-30. rusted bore like you wouldn't believe. shoots like a dream lol. thanks for posting mosin.
@vladimirboskovic
6 жыл бұрын
use FAIRY dish washer best way for dark bores
@MosinVirus
6 жыл бұрын
Thank you. I will take a look.
@GodWasAnAlien
4 жыл бұрын
Good video. Hope you're being careful when you pull that brass tip back through the muzzle though, I've nicked a couple of crowns that way in my younger days.
@MosinVirus
4 жыл бұрын
Trying my best to avoid it.
@mklean1
9 жыл бұрын
As always, thanks for sharing. Just ordered some to try. I've spent more than the $6 on much more frivalous things. And if it doesn't work I can always clean my frying pans.lol BTW Have you tried their cleaning solvent?
@MosinVirus
9 жыл бұрын
mklean1 Hello. No I haven't tried their solvent, because I really like Hoppe's Elite bore gel. It is non lubricating, so the gunk washes off the brushes really easily under running water, and it cleans better than many other things I have tried.
@MosinVirus
9 жыл бұрын
mklean1 forgot to add that after using that bore gel you have to oil the bore since there is no real protection in the gel.
@MosinVirus
9 жыл бұрын
mklean1 BTW, when you do try it, please let me know how it did. I am pretty sure you will be pleasantly surprised.
@mklean1
9 жыл бұрын
Thank you for taking the time to reply. Will let you know how it works for me. Have an SKS that I sent off the bolt and trigger group to have tuned up a bit. Want to gice them a nice clean place to come home to.
@tristanmyers897
4 жыл бұрын
Not saying frog lube does this with every solvent but the people at the gun shop I work at made the mistake of cleaning the ar15 rifles we use for navy quals and then switched to remoil and COLD NOT for the life of them stop the guns from rusting due to the chemical reaction of the remoil and frog lube in the pores of the metal... or so the story goes. So I don't recommend mixing any lube/cleaner with frog lube
@MosinVirus
4 жыл бұрын
Interesting. I will try and test it out on some scrap steel.
@tristanmyers897
4 жыл бұрын
@@MosinVirus I'd be interested in the results but I'm not sure how long they used frog lube before switching or how long it takes to seap into the pores of metal
@cuda4094
6 жыл бұрын
Yeah it's called 4 -00O steel wool. That would WD-40 works wonders. Took pitting off a 357 Magnum looks brand new.
@MosinVirus
6 жыл бұрын
0000 steel wool will actually remove material. it is much more abrasive than the product in the video.
@cuda4094
6 жыл бұрын
MosinVirus very small amount. Not even noticeable. I use the same method on a blued Taurus 357 Magnum. Came out even shinier looks brand new. No more rust pitting or corrosion. I use the same method on a spear bayonet on my Mosin Nagant. It works
@MosinVirus
6 жыл бұрын
I don't doubt it. But be careful, it will remove bluing.
@cuda4094
6 жыл бұрын
MosinVirus it will only remove bluing if you don't use oil and if you rub aggressively and with a lot of pressure. However in a barrel that is already corroded who cares you're just trying to get the most gunk out as possible.
@alexb.6466
9 жыл бұрын
By load up do you mean get dirty faster and harder to ckean?
@MosinVirus
9 жыл бұрын
yes, the usual remnants of shooting will get into the pits. that is mainly why people with some older guns never get a white patch out of their bores. that is not really an issue though, and as long as you have good lands and tight bore, the accuracy will not be affected.
@pizzapizza2424
7 жыл бұрын
MosinVirus if you take the time to clean even the pits out and then use some good oils that repel dirt/fouling you can start to get a patina pretty much so that if you continue to shoot it and fully clean (with the same oils) it you can fill in the pittings and make it smooth like a cast iron pot. (cast iron pots start out with a lot of holes in them and the "seasoning" process fills them in) pretty much filling the pitting and can give you better groups. you can block the barrel and fill it with a clp and let it sit as a good way to soak the barrel with gun oil to make it easier to clean. (with a lot of mosins an empty shell casing is a good way to seal the barrel and it can catch anything that the oil pulls off)
@MosinVirus
7 жыл бұрын
pizzapizza2424 cool idea about the casing.
@pizzapizza2424
7 жыл бұрын
MosinVirus its worked for all of mine. using that method all of mine have patches come out looking the same color as when i put them through with any product ive tried. and after shooting 2 or 3 tight fitting patches gets them clean if ive shot less than about 50 rounds (shooting corrosive ammo) and whether i use a brush or not the patches come out clean after that. the oils i use form a protective barrier to keep anything from sticking well
@MosinVirus
7 жыл бұрын
pizzapizza2424 thank you. I assume we are still talking about pitted bores?
5 жыл бұрын
0000 steel wool stripped of it's grease works the same
@MosinVirus
5 жыл бұрын
I would think that steel wool would actually wear the bore out eventually.
5 жыл бұрын
@@MosinVirus You only use it with gun oil and when you first buy an old gun. 0000 steel wool and oil cleans outside rust off of barrels and other parts without doing anything to the bluing.
@MosinVirus
5 жыл бұрын
Understood. Thank you for sharing.
@pinkeye00
7 жыл бұрын
Why not bore foam?
@MosinVirus
7 жыл бұрын
pinkeye00 doesn't work as well. honestly. give it a try and you will see.
@pinkeye00
7 жыл бұрын
gotta let it sit, and then repeat the process. It's not a one time treatment and done. However, I'll see what you're getting at this week ... couple CnR type things coming in.
@MosinVirus
7 жыл бұрын
pinkeye00 I know. the only problem with most foam cleaners is that it is not always good to leave them in for very long periods of time. Well, it is up to you. but I would still recommend you try this cleaner.
@pinkeye00
7 жыл бұрын
I use foam on an old barrel then use a bore snake with patch cleans.
@mesothelioma5024
5 жыл бұрын
Home Depot would have this right?
@MosinVirus
5 жыл бұрын
I bought online from here www.big45metalcleaner.com/
@MrIdasam
7 жыл бұрын
It IS that thing to you use to clean dishes. It's a Scotch-Brite pad, nothing more. I was foolish enough to order one. I just happen to have a pack of Scotch-Brite pads already and I compared them; identical. Don't waste your money.
@MosinVirus
7 жыл бұрын
I am pretty sure the alloy is different. I acutally think the Scotch-Brite is a bit more aggressive.
@spadetrump
5 жыл бұрын
@@MosinVirus that may be. but I have used the Dollar store scotch brite pads. use the ones that say pure copper... it worked for me. but if you want to be safe... get the expensive one i guess.
@MosinVirus
5 жыл бұрын
@@spadetrump pure copper would obviously not damage anything.
@spadetrump
5 жыл бұрын
@@MosinVirus yes. They are brand name Chore Boy and they are pure copper. thats what I used on a CZ 70 that had been neglected. worked good.
@spadetrump
5 жыл бұрын
I am going to order one of these frontier 45 pads since they are cheaper on eBay than amazon.. just to test.
@LoveMyKleeKai
8 жыл бұрын
whats the green stuff?
@MosinVirus
8 жыл бұрын
Not sure what you mean.
@LoveMyKleeKai
8 жыл бұрын
green liquid you used the other one not hoppes
@MosinVirus
8 жыл бұрын
Oh, Frog Lube. I have stopped using it though. It becomes a gunky mess after sitting for a while. I am now using basically two things - Hoppe's Elite Bore Gel (for fast cleaning) and Ballistol for rust protection, lubrication, etc.
@LoveMyKleeKai
8 жыл бұрын
you found that hoppes elite tough enough to remove the rust?
@MosinVirus
8 жыл бұрын
No. Rust usually requires specific rust removing chemicals or mechanical removal that the wad in the video is great at.
@j.sagiechode
5 жыл бұрын
Looks like alot of physical labor, let me interject my method.. I plastisine/clay plug the crown then I flood the barrel with karosene/engine degreaser right up all the way to include the chamber, then prop it up against the wall for a couple days, then I drain the barrel run a patch or two and done.. spotless and looks factory new. simple and cheap and little to no labor.
@MosinVirus
5 жыл бұрын
Definitely sounds like a great method. Will try when I have space. Cant do it inside, the fumes would be super bad.
@hansvonmannschaft9062
5 жыл бұрын
And when you thought that molotov cocktails couldn't be improved, this gentleman shows up with... molotov javelins! woohoo! Let's just hope those antifa pieces of shit don't see your comment :-)
@schubi128
4 жыл бұрын
You lost me when you went back and Forth Inside the bore with the Bronze brush. this really hurts.
@MosinVirus
4 жыл бұрын
I am sorry this video disappointed you.
@schubi128
4 жыл бұрын
@@MosinVirus Not me but the bore 😉 But Maybe I'm more sensitive then the barrel
@MosinVirus
4 жыл бұрын
That brush is worn down btw. If the brush was good it would have been a real chore to make the bristles pop the other way. I can't remember if I mentioned it in the video or not, it was a long time ago. The Big 45 metal cleaner "wrap" works best on worn down brushes. You can use more of it on the brush that way. That is why i never toss old brushes.
@mistergrendel32
7 ай бұрын
@@MosinVirusI would think that back and forth is fine. Just don’t change direction within the barrel. Everybody knows that right? 🤔😜
@MosinVirus
7 ай бұрын
@@mistergrendel32 unless the brush is smaller diameter or worn to the point where bristles will not fight back.
@shelbymiller4116
7 жыл бұрын
u need a bore guide so u dont fuck up the rifling
@neilbreen6998
7 жыл бұрын
carbon rod wont do damage.
@MosinVirus
7 жыл бұрын
Breen Machine that is what I thought too. thank you.
@ShoppingForDollars
9 жыл бұрын
Get a viper boresnake
@MosinVirus
9 жыл бұрын
Got one. Not even close in my opinion.
@wcdjmase
9 жыл бұрын
MosinVirus I agree; the snakes are great for maintenance, but nothing beats a good 'ol rod, brush and patch for the older firearms
@MosinVirus
9 жыл бұрын
Adam Kushner Couldn't have said it better myself. Thank you.
@gearhead6424
6 жыл бұрын
Holy fuck. You need patience to watch this video
@MosinVirus
6 жыл бұрын
Sorry. It was one of my earlier ones.
@robertbrandywine
4 жыл бұрын
@@MosinVirus Don't apologize. There is a soothing ASMR factor to it.
@kfaposse
5 жыл бұрын
Buy some lighting.........
@MosinVirus
5 жыл бұрын
I actually got some recently. Sorry about the earlier videos.
@samuelconrey7372
6 жыл бұрын
I may be wrong, but it seems to me that running scotchbrite down the barrel would be far more harmful than helpful....
@MosinVirus
6 жыл бұрын
This product doesn't even take bluing off.
@Honk_Clank
6 жыл бұрын
Looks like 0000 steel wool wrapped around a brass brush more or less.
@MosinVirus
6 жыл бұрын
Very different. Steel wool would remove bluing in a heartbeat. This removes top rust but leaves bluing untouched. Might be closer to some cleaning pads. Not sure which but definitely different from steel wool.
@thesmokinggun8674
7 жыл бұрын
Couldn't you just use a regular dish scrubby in the same manner?
@MosinVirus
7 жыл бұрын
Smokinggun1911 A1 possibly, but I seem to remember them being more aggressive.
@thesmokinggun8674
7 жыл бұрын
MosinVirus do you think it would be worth a try?
@MosinVirus
7 жыл бұрын
Smokinggun1911 A1 try in a hidden area. If it removes bluing, it is too aggressive.
@thesmokinggun8674
7 жыл бұрын
MosinVirus okay thanks.
@huannguyenquoc1671
10 жыл бұрын
súng rất đẹp.......
@MosinVirus
10 жыл бұрын
Cảm ơn bạn. Đó là một khẩu súng rất đẹp và một trong những mục yêu thích của tôi.
@huannguyenquoc1671
10 жыл бұрын
tôi cũng rất thích tìm hiểu về súng.mong bạn đăng nhiều hơn để được nhìn những khẩu súng đẹp...cảm ơn bạn rất nhiều....
@johnetattoo
8 жыл бұрын
You can get those metal pads at the dollar store for almost free................
@MosinVirus
8 жыл бұрын
+JohnEtattoo Not sure it is the same, but I will look and see. Thanks.
@johnetattoo
8 жыл бұрын
I'm not sure if its the same either but I'm going to look into it myself. I have a 91/30 I just bought and the bore is pretty rusty.
@Fireworxs2012
8 жыл бұрын
It takes 6:29 for you to GET TO THE FUCKING POINT....GOOOD GRIEF...By the way... You can accomplish the exact same thing with a strip of scotch brite, a little WD-40 and a patch jag...
Пікірлер: 313