Hell yeah. This is one of the videos that helped me decide on the 85 as my first quad. Nice flying man :)
@alex_k21
6 ай бұрын
Awesome! Thank you!
@alexanderwharton1434
10 ай бұрын
Great footage buddy, interesting modifications i see bellow on the comments...congrats!
@alex_k21
10 ай бұрын
Thanks 👍
@babyzfpv1234
Жыл бұрын
I have one of these things, and it keeps failsafe thing and dropping out of the sky. How do you have this thing set up in betaflight? I can keep it flying it close range with crystal clear VTX, but for some reason my Little Bitty literadio2 from Beta FPV loses signal. But with the 65pro I can fly that drone pretty damn far away. Any tips?
@alex_k21
Жыл бұрын
I did not change the settings in betaflight, all settings are from the manufacturer. I'm using a LiteRadio 3 ExpressLRS 2.4G remote and it has a good connection. When flying over long distances, the video connection will disappear much earlier, but definitely not the connection with the remote control
@LoVeAmBiEnT
Ай бұрын
You’re probably burned out the VTX. Setting it up in beta flight and keeping it on too long w the 400mw on . What’s gonna happen is you’re gonna get it up in the air within 10 to 15 seconds it’s going to lose signal and drop out of the sky. or on land on its own, you just need to buy a new one or replace the flight controller
@FregoUA
Жыл бұрын
Огонь бро! Хороший пикник
@alex_k21
Жыл бұрын
😁
@MirrorBoySkr
4 ай бұрын
Hi! Great video!!! Quick question. I had Meteor 65pro (ELRS) + RadioMaster Pocket Then I bought Meteor 85 (ELRS). I couldn't bind either by button or by a bind phrase. After a long investigation, I discovered that the Pocket transmitter works on 1000Hz, but the Drone 85 only supports 500Hz. So, I had to changes Packet Rate on the Pocket to 500Hz. So, now both my Meteors are connected with the Pocket. Did you have the same issue?
@alex_k21
4 ай бұрын
Hi! I didn't have issues with ELRS connection. My Radiomaster Zorro was connected with meteor through betaflight configurator, when it was with Elrs v2. Now my Zorro has elrs v3 and I use it only with CineLog 25. For my old tinywoops I use Betafpv LightRadio3
@abgamma
4 ай бұрын
To put it into bind mode, you need to remove and reconnect power 3 times.
@DouglasDrones
Ай бұрын
Um tinyhawk 2 carrega uma câmera como essa ?
@alex_k21
Ай бұрын
easy
@LoVeAmBiEnT
Ай бұрын
Is there a 5 V and ground on the flight controller that you just tapped into with the runcam?
@alex_k21
Ай бұрын
yes, there are several free contact pads with +5V and ground
@YouFPVtube
6 ай бұрын
Und wie weit kommst du mit dem Antennen?
@RC.Drone.Pilot.Fun.
8 ай бұрын
Вери гуд
@alex_k21
8 ай бұрын
Thanks)
@Flux_vids
10 ай бұрын
how do you atenna swap the goggles?
@alex_k21
10 ай бұрын
I bought a long antenna with RP-SMA connector (Polarisation:RHCP, 5.8G) from an online shop. Unscrew the original antenna and screw on a new one instead, that's all)
@nightzx9689
11 ай бұрын
pls do video about your setup and google modification
@alex_k21
10 ай бұрын
I bought a long antenna with RP-SMA connector (Polarisation:RHCP, 5.8G) from an online shop. Unscrew the original antenna and screw on a new one instead, that's all)
@TheRealFpvKev
Жыл бұрын
What kind of antenna do you have on those goggles?
@alex_k21
Жыл бұрын
Lollipop 4 mini RHCP 5.8G (Long Purple RPSMA)
@pawelec8076
Жыл бұрын
what is the antenna on the goggles? Is there a difference compared to the stock antenna?
@alex_k21
Жыл бұрын
Antenna -Lollipop 4 5.8G Mini RHCP long RPSMA. Yes, the connection quality is much better if you put the same antenna on the drone (but with a UFL connector). With these antennas, I can fly much farther without signal degradation.
@pawelec8076
Жыл бұрын
@@alex_k21 when you change antenna on the drone, did you have to solder that?
@alex_k21
Жыл бұрын
@@pawelec8076 No, there is an RP SMA connection. you just need to unscrew the original antenna and screw on the new one
@megatron187
10 ай бұрын
how to swap the antenna on the drone tho...?
@alex_k21
10 ай бұрын
buy an antenna with the appropriate polarization (RHCP) like on a helmet and a corresponding connector (UFL), remove the old antenna, install a new one
@sharptechnique7883
Жыл бұрын
Is this the elrs version?
@alex_k21
Жыл бұрын
Yes, Elrs
@YouFPVtube
6 ай бұрын
Как дальность с этими антеннами?
@alex_k21
6 ай бұрын
Качество сигнала значительно лучше чем со стоковой антенной. Дальше 200 м я не летаю, но залетая за дерево помех значительно меньше, на оригинальной антенне можно потерять дрон в 50м за деревом
@РинатНаркаев-л5з
Жыл бұрын
😀😃😄
@ivankoreshkov5140
10 ай бұрын
Frsky + analog? (From Cetus series)
@alex_k21
10 ай бұрын
elrs + analog (VR03 FPV Goggles from cetus x kit, Betaflight FC)
@ivankoreshkov5140
9 ай бұрын
@@alex_k21 спасибо 👍
@wtfhk4864
Жыл бұрын
How to make Meteor85 FPV drone with Runcam Thumb camera on top? can you take a video :)
@alex_k21
Жыл бұрын
The camera is attached with three plastic ties - one long one through the canopy, and two short ties attach the camera mount to the first tie. The camera is powered by the flight controller. I soldered a connector in the corner of the flight controller to the 5 volt pins next to the buzzer pins. If necessary, the camera can be turned off and removed from the drone.
Пікірлер: 42