Please note that I installed the propellers guard upside down by mistake. Happy flying!
@WEEBER13
10 ай бұрын
it looks correct to me! In the beginning shots, it's correct, but later in the video I see what youre saying. It is incorrect 1/2 way through when you are pulling the guard off the carbon frame.
@KremerFPV
10 ай бұрын
@@WEEBER13 Yes I made a mistake when putting it back the last time :-)
@dronefilmsgermany
7 күн бұрын
What is the weight with battery but without GoPro. Can I go below 250 grams with the Pavo 25 v2
@MCsCreations
10 ай бұрын
Awesome flying and review, Gal! 😃 Really nice little quad! Stay safe there with your family! 🖖😊
@KremerFPV
10 ай бұрын
Thanks Mario!
@grege2383
6 ай бұрын
How does this compare to the Flywoo Flylens85? I'm on the fence between the 2.
@WeAero
5 ай бұрын
your prop guards are installed upside down.... hehe
@larkin-denys6910
10 ай бұрын
Is this drone capable of carrying a full size gopro camera and djio o3 system for indoor filming? Thanks for the video!
@KremerFPV
10 ай бұрын
Yes it might be possible but it will be too heavy. I recommend going for a naked GoPro or similar.
@Dorff_Meister
6 ай бұрын
Thanks for this. I've decided to upgrade my Mob8 w/O3 to the Pavo25 v2. I'll move the O3 and retire the Mob8. The Mob8 really isn't strong enough to carry an O3 especially if there is much wind, but it was fun for my first quad. I got a lot of great hours with it.
@gusagus550
5 ай бұрын
best whoop for 4s batery
@ekonurhadisaputro9493
13 күн бұрын
Hallo, can you share your PID for Pavo 25 v2??..
@KremerFPV
13 күн бұрын
Please check the video description.
@SkyBlue2020
10 ай бұрын
The frame was assembled upside down.
@KremerFPV
9 ай бұрын
Yes - my bad.
@jeevandewee
8 ай бұрын
Nice review. Did you see any jellowing? Although the dampening seesm stiff, I did not see any jellowing in your video. Or did I miss it?
@KremerFPV
8 ай бұрын
Thanks. Flight footage was quite smooth actually.
@zeriusfpv
10 ай бұрын
the prop guards looks weird, and found that you install the prop guards in wrong side Gal 😃
@KremerFPV
10 ай бұрын
Yes, my bad :-)
@InternetBaikBuruk
10 ай бұрын
Omg.. it is so good quad... 👍👍👍 Lucky you 👏👏
@jorgelbotelho8363
10 ай бұрын
Muito bom e melhor do que a Aurora 90
@KremerFPV
10 ай бұрын
Yes indeed :-)
@damianwyczakowski2491
10 ай бұрын
Hello Kremerfpv
@KremerFPV
10 ай бұрын
👋
@WEEBER13
10 ай бұрын
GREAT review Gal. Do you know if the frame will accommodate a 30X30 FC or 20X20 FC? I'm thinking about building my own with 1507 motors and chopping 3" props down to size...
@KremerFPV
10 ай бұрын
Thank you! It supports 16,20 and 25mm stacks.
@WEEBER13
10 ай бұрын
Thanks, @@KremerFPV !! Really appreciate your reply! I was thinking about maybe sticking a DJI Vista in there, if it fit!
@KremerFPV
10 ай бұрын
@@WEEBER13 no worries. Sure, it will fit :-)
@jonatancruz3238
10 ай бұрын
los ductos no estan el revez?
@WEEBER13
10 ай бұрын
I wondered the same thing! @jonatancruz3238
@KremerFPV
10 ай бұрын
@@WEEBER13 yes, I made a mistake :-)
@lalojr76ify
8 ай бұрын
Where did you purchase the data cable device and the 90 degree micro usb device. I’m having to take my motor off to connect my data cable.
@KremerFPV
8 ай бұрын
You need a USB-C extension cable such as this one: s.click.aliexpress.com/e/_ol6bVdm
@panosfpv
8 ай бұрын
Hello Gal. Which extension specific? I saw in the video U had a blue one not flexible? Thank you.
@KremerFPV
8 ай бұрын
@@panosfpv Hi, I don’t have a link to the specific version that I have. The TYPE-C version from the link above should work.
@kimeunsankim8859
10 ай бұрын
BWhoop Duct roll ???
@kardady
10 ай бұрын
Looks great. Thanks for sharing, Gal 🙏
@KremerFPV
10 ай бұрын
My pleasure!
@mazivco
9 ай бұрын
I just configured the Pavo and couldn’t figure out how to turn off the led
@KremerFPV
9 ай бұрын
Do you still need help with that?
@mazivco
9 ай бұрын
@@KremerFPV I already figured it out but now I’m trying to make the osd work on my goggles 2 and I would appreciate your help with that. I’m confused what needs to be done in beta flight
@KremerFPV
9 ай бұрын
@@mazivco easiest option is to use the DJI O3 preset (under presets tab on BF). You need to select the UART that is connected to the O3 unit. Make sure that RX is wired to TX from thr O3 unit to the FC (And vice versa).
Пікірлер: 44