Much appreciated my friend! Glad it was able to help. 🤝🏻
@AmstafStaf
3 ай бұрын
Thx for the video !
@raivons
2 жыл бұрын
Worked! Thank you
@BFTAmericasInc
2 жыл бұрын
Glad it helped
@eapanenmas
11 ай бұрын
To communicate using rs485, what commands must be sent to open the arm or close the arm?
@paulhutton6664
2 ай бұрын
Followed your very clear instructions to a Tee. I pressed the hidden button on the new BFT remote when instructed then pressed the desired button but unfortunately the display keeps showing 'ko' so kept trying starting from the beginning but to no avail. What does this mean and could you help? Many thanks.
@bradjessop3137
2 жыл бұрын
Thank you, great demonstration. Is 63 remotes the maximum or can I put more than 63?
@BFTAmericasInc
2 жыл бұрын
Yes 63 is the maximum, but we do offer the Clonix 2E wired in receiver which will allow you to add from 128 to 2048 more remotes if needed. Check this link out kzitem.info/news/bejne/pq2Prp-LmGh8iJg
@russellpugh617
Жыл бұрын
Thanks for sharing and I have a similar question to one below, I have a gate with 2 elements and the original remote left button would open both elements and the right button would open only the right gate element. So how do I program the right button without overwriting the left button function that would of been then programmed via the routine displayed in your clip. In a nutshell how do I program both buttons on a single remote in conjunction with a dual gate operated by a single controller? thanks...
@BFTAmericasInc
Жыл бұрын
To do this the button that you want to open both gates together you would go to the Radio Menu and select Add Start and go through that process to work both gates. Then for the other button to work just one gate; when you go to the Radio Menu hit the minus (-) button one time and select add Ch 2 and go through that process and select the other button to open just the one side of the gate.
@RomanRoman-xi3dv
8 ай бұрын
@@BFTAmericasInchello, i have coded replacement remote controller. Can i add it somehow to a motor without oppening motor unit? Can it be added to a motor unit by using original working remote?
@prameshcctv3668
8 ай бұрын
thankyou
@fequalsma42
2 жыл бұрын
Does this work with the generic multicode remote or does it need to be mitto remote? (Trying to use a universal remote for garage and gate)
@BFTAmericasInc
2 жыл бұрын
This will only work with our BFT Products. If you would like to use Multicode remotes you will have to also purchase a wired in Multicode receiver and program to that.
@raymondlee0215
2 жыл бұрын
Thanks. It works great
@BFTAmericasInc
2 жыл бұрын
Great to hear! Enjoy!!!
@bellebutton5101
2 жыл бұрын
Hi, does this work for re-programming existing remotes? We have 2 set to "pedestrian" we wish to change to open completely. Thankyou
@BFTAmericasInc
2 жыл бұрын
Yes, when you do this process you can overwrite an existing function that the specific button used to do, or you could just program another button to full open and leave the other to pedestrian to keep both functions. Up to you. 👍
@mihai6148
Жыл бұрын
I have a question, how do I program one of the remote buttons to stop de gate from closing, since it's set to automatically close after a couple of seconds? Thank you
@BFTAmericasInc
Жыл бұрын
There are 2 ways you can do this 1st. turn off the automatic closing and use the remote to open and close the gate and 2nd. if you need to keep the automatic closing turned on then right when it starts to close press the remote button to stop the gate.
@Vietsical
2 жыл бұрын
I have an ultra gate opener and 3 of the remotes I have are now dead. So if I buy the bft gate remotes that look exactly like mine on Amazon, would I be able to reprogram to make the gate work ont he ew remotes? Thanks
@BFTAmericasInc
2 жыл бұрын
If you search for BFT Mitto 2 or 4 something should pop up and those should work ok as long as you follow the video instructions. But you might want to try replacing the remote batteries (A23). If the red light comes on when you push the button after replacing batteries try to reprogram remote.
@marinjovic9017
Жыл бұрын
Is there a way to program the the garage opener which is integrated in the rear view mirror of a car? Can't find anything on the web...tried it on a bmw, but it doesn't work.
@BFTAmericasInc
11 ай бұрын
you would need a homelink kit that would wire into the control board
@stevendang4218
2 жыл бұрын
thanks however i did exactly the same as your instruction but can not see hidden button please give advices many thanks love your video
@BFTAmericasInc
2 жыл бұрын
I'm sorry to hear that. Send us a photo or small video of what is happening to tech@bft-usa.com. Also, Make sure that the board is in english if you are looking specifically for the word "hidden button".
@life0storm
Жыл бұрын
My remote is MITTO 4 for three doors since our garage is on 3 levels, so it uses 3/4 buttons - hold by one operating device can I program it somehow to work the same as my primary one? Should I program the buttons one by one or it doesn't work like that? Thank you in advance
@BFTAmericasInc
Жыл бұрын
I am unsure of what your asking but each button can be programmed to a different control board. If you like you can email us at tech@bft-usa.com for more help
@adrianzanoli
2 жыл бұрын
I have 3 gates connected with this unit. How i program a BFT 4 buttons in a way that every button open a different gate?
@BFTAmericasInc
2 жыл бұрын
You would simply repeat the process in this video with each gate operator control board. Just make sure, when you get to Minute 1 second 49 of this video, you are selecting a different button per operator.
@adrianzanoli
2 жыл бұрын
@@BFTAmericasInc there is only 1 control board for 3 gates, i think. I did the procedure correctly and it added the remote, the remote works, but it open only 1 gate.
@telceker
3 жыл бұрын
Bulunduğum sitenin yöneticisiyim Urano BT model otomatik kapı sistemi var. BTF kumandayı sizin ki gibi kopyalamaya çalışıyorum ama olmuyor. Yardımcı olur musunuz
@BFTAmericasInc
3 жыл бұрын
Que?
@dannytaams5514
3 ай бұрын
I tried this, but didn't work. The "hidden button" doesn't appear on the screen. At some point (after pushing all the buttons you mentioned), it says " - someting - second". Any experience with that?
@BFTAmericasInc
3 ай бұрын
If you give us a call at 877-995-8155 option 3 for tech support we can help you walk through it as well.
@ikatsikoridze3492
Жыл бұрын
Hello, My bft has no display, I bought it around 12 years ago. How can I programme it?
@BFTAmericasInc
Жыл бұрын
On the top if the control board there should be 3 buttons the top button press one time and a LED right next to it should start blinking when it does hold the 2 buttons of the remote together when the light that is blinking goes solid let go of both buttons then press the button you want to control the gate with and then that solid button should start blinking again showing that the remote is programmed. If that doesn't work go ahead and take a picture of your board and send it to tech@bft-usa.com so we can better help you in programming the remotes.
@jakekim9019
2 жыл бұрын
Hi, mine shuts off in few seconds while setting. Could you help me with this please?
@BFTAmericasInc
2 жыл бұрын
Looks like you figured out the jumper needed for programming. 👍🏻
@mrlengau95
6 ай бұрын
I have problem with the remot. For open the gate using remot is working normaly, but when i want to close the remot using the remot is not working and there is "Er 35" Every time i press the button for close the gate
@mrlengau95
6 ай бұрын
I already use 2 different remot and its still not working 😅
@BFTAmericasInc
4 ай бұрын
Er35 is an obstruction error, if there is no obstruction in the way you may need to increase the force setting. If you like send us an email at Tech@bft-usa.com and we can either give you a call or send instruction on how to increase it.
@technologytoopens.p.a281
2 жыл бұрын
Need complete programming video bft maxima ultra36
@BFTAmericasInc
2 жыл бұрын
Sure! Check out our "Maxima Play List" with several tips and tricks. Try this link out.... kzitem.info/door/PLy2R7OEbZmjJDj5WPUtW_Ptxj1oGCZVTM
@sniper29292
Жыл бұрын
If there no screen.. How to program
@BFTAmericasInc
Жыл бұрын
No problem, Check this video out. Sorry that it is in Spanish, but if you follow along and just do what you see, it should be no problem. kzitem.info/news/bejne/t4KnyKeoq3p3mYI
@garygab4800
Жыл бұрын
How do I fix this system because it’s hooked up to my gate and when I press the top left button it goes but only opens half way is there a way to fix that
@BFTAmericasInc
Жыл бұрын
When you press the button does it say Ped on the display of the control board
@utos2195
6 ай бұрын
My friend gave me your contact number.. i have one issue with the new BFT control board. For adding remoute, i found up to radio after i can't find a hidden setting
@saleemsiddique848
2 жыл бұрын
Help me plz My barrier Display show Er 20
@BFTAmericasInc
2 жыл бұрын
Sounds like an Encoder Error. Reach out to us at Tech@BFT-USA.com.
@joaquimmaiamaia3533
10 ай бұрын
Traduzir estas paginas para Portugues
@mongkhon9999
2 жыл бұрын
er 36 i dont know how to fix
@BFTAmericasInc
2 жыл бұрын
ER 36 is an obstacle detection during the closing cycle. Make sure your gate is closing with no issues when you push the gate manually. If there is nothing impeding the movement of the gate try to raise the torque in the "Parameters" menu. If you are still having issues please write us at Tech@BFT-USA.com and we will see if we can assist you further.
@NatesToolbox
Жыл бұрын
Worst board design ever just have an onboard program button or at least a proper English multi line screen like everyone else
Пікірлер: 56