That sound take me immediatly to my youth, those cold mornings, when my dad was hurrying up to take their children in time to school!
@rustbeltbuilds
2 жыл бұрын
Holding onto that memory is the most important thing
@jumpinjojo
Жыл бұрын
*Immediately
@mrg52u11
7 ай бұрын
@@jumpinjojothink it was flooded a little?
@Thebumpinthenight
6 ай бұрын
My pops had a 68 c20 with a 327 and side pipes before the rear tire. I was the coolest kid at school
@stephenwest798
Жыл бұрын
Just so you know, the 318 four barrel and the 360 four barrel, with TQ carbs both came with 800 cfm carbs, so I don't believe an 850-cfm carb on that engine with that cam is too large. I run a 750 cfm on my 360 with smog heads a performer cam and intake and stock exhaust manifolds, it was basically dead with a smaller carb on it. An electric fuel pump so you could fill your carb with gas after it has been sitting will save you from cranking so long to get fuel to your carb and save your starter as well. Awesome sounding engine, great exhaust system, I missed the burnout, or at least I was hoping to see one.
@NJFordPops08005
3 жыл бұрын
very nice, love the cranking, love that old Mopar sound.
@ryanhruska6667
2 жыл бұрын
Just so the world knows, big cams and compression saves lives 👍👍 Awesome sounding truck bro 👍
@patgraeme775
Жыл бұрын
A handful of timing saves starters
@lovetocrank
3 жыл бұрын
I love this video! The sound of that Mopar starter is tremendous!
@rustbeltbuilds
3 жыл бұрын
We have an Instagram- rustbeltbuilds
@lovetocrank
3 жыл бұрын
How about email? I am at lovetocrank@yahoo.com
@RbaTmaR420
2 жыл бұрын
Yeah you cannot mistake the sound of them old mopar starters. He could buy a high torque and slap it rite on there. But love he stayed with the old school.
@mopardude707
2 жыл бұрын
Same here bud I love my 96 ram I love the way it sounds when cranking 👍
@lovetocrank
2 жыл бұрын
That has a great sound, I agree! Do you like it when you have to crank it over a couple of times before it starts?
@tsi87supr60
2 жыл бұрын
Tune that carb. Look up uncle Tony's garage on here. He has carb tuning videos that will remove the hesitation from the 850.
@Ratridez
3 жыл бұрын
Starter works 🤣 Sounds awesome bud , my engine turns awhile to from setting especially with an edelbrock.
@throttleblipsntwistedgrips1992
3 жыл бұрын
Love that sound, mine takes about as long to start, You feather the pedal? I just stomp on it once in mine to set the choke. Could get a good shave in before itll catch😂
@oldfart8501
Жыл бұрын
Starters on mopars always sound like a dolphin in a headlock
@Timmermon63
5 ай бұрын
That’s the best description of a Chrysler starter ever!
@JohnWhite-xc3md
4 ай бұрын
Not when they're running right. My 440, and 340 Magnums would fire immediately. To be fair, I never let them sit for two weeks. All the Mopars I ever owned, or my parents cars started without hesitation. They chryslers from '65 to about '73 were excellent. Never had any real problems. My Mom's Cadillac? Totally different story.
@elijah2078
4 ай бұрын
I will say that most of the old gm starters sounds like a coffee can full of rocks. They are also the only ones that needs shimming and usually destroys flywheels.
@jonjones6749
Ай бұрын
@@JohnWhite-xc3md My Hemi starts just like this. Hard starting.
@3074x4-Garage
Ай бұрын
Lmao! I love it!
@C_71
3 жыл бұрын
If it's not timing it sounds like the only thing he needs is an electric fuel pump to prime the engine. This thing sounds beautiful! I'm just getting my 78 D150 running after buying it last October...I'm going to cam and put aluminum heads on it with a 750cfm carb.
@rustbeltbuilds
3 жыл бұрын
It has an electric pump wired up but it’s not hooked to fuel tank
@deleonsoto4675
2 жыл бұрын
Had to show the pistol. Lol thought you were from Texas til I saw that for sale
@allanmcelroy9840
3 жыл бұрын
Now THAT is a big aggressive sound...even for small block 360. I have same engine, but with a 20-602-9 cam for towing. The idle ain't that aggressive.
@beefdrapemudflapper930
3 жыл бұрын
Cool truck. I have a 74. I used to think they were ugly until I got one. Now I see the beauty in them.
@wesleynash2598
3 жыл бұрын
I just got a 1975 Dodge d300 dually and I want it to sound like this!
@slomotrainwreck
3 жыл бұрын
That idle sounds wicked! Nope, don't want to see a Stoopid tire roasting burnout - been done to death. With that cam I want to hear a straight up 20 to 100 pull.
@rustbeltbuilds
3 жыл бұрын
Will do
@tedunguent156
Жыл бұрын
Yeah, I'll bet all of your neighbors LOVE that.
@reaper-sz5tm
3 жыл бұрын
My friend, you need a high torque starter from the magnum engines. Best swap you’ll do for a cam that big lol
@rlutzmec4290
3 жыл бұрын
It has one
@throttleblipsntwistedgrips1992
3 жыл бұрын
360s just take that long to start. Brand new Edelbrock 650 and stock cam in mine and it takes a couple seconds before itll catch. Longer if it's hot out and boils the fuel out of the bowls.
@brandonpurple8938
2 жыл бұрын
@@throttleblipsntwistedgrips1992 my Magnum 360 starts right up the right fueling and a good starter it should fire up I had a 86 c10 with a 350 with a 4 barrel and it basically would start right up
@tl5108
2 жыл бұрын
A lot of has to do where the initial timing is set
@roachcoachhelis6387
2 жыл бұрын
@@tl5108 he said it had been setting for 2 weeks any carbureted engine cranks for a while after setting that long my 350 Chevy sure does
@MrGeegsters
3 жыл бұрын
Nothing like mopar tech. I enjoyed my supercharged 5.9. Of course it didn’t last but it was one hell of a truck
@rustbeltbuilds
3 жыл бұрын
More big cam cold starts on the channel!!!
@teacatstudios3236
3 жыл бұрын
How much?
@brianszempruch8353
2 жыл бұрын
How much are you asking for it?
@RedBarnFX
2 жыл бұрын
I was a running a Delphi mechanical fuel and a barrel style fuel filter like you have in your 360. I changed out the Delphi for a Carter.. No difference. I changed out the barrel filter for a slim glass one and boy that made a difference in start up. If you’re running a Glycerin filled fuel pressure gauge make sure you cut the tiny nipple off the rubber plug on top. It helps the heat escape for a accurate fuel reading! Those 360s detonate and get hot quick if fuel starved. Beautiful truck and sounds awesome!
@Wr3ckZ
3 жыл бұрын
I wanna click Like, but it's on 360!! Consider this your like! Correction: Consider this the Love! I love it!
@Gabriel-jx1fv
Жыл бұрын
Hell Yeah... Cousin phuck Yeah!
@brianwarner6121
2 жыл бұрын
Gotta love mechanical fuel pumps.
@WyoCutlass71
Жыл бұрын
What is the tire size that you got on this truck to get this stance?
@rustbeltbuilds
Жыл бұрын
I cannot remember. I think they were atleast 28inch front and rear maybe 29 in the rear
@DanBlackRacing
2 жыл бұрын
My God in heaven 🔥🔥🔥🔥🔥🔥 nothing sounds more amazing.
@rustbeltbuilds
2 жыл бұрын
Check out our Camaro cold start
@stopchangingmyname4017
3 жыл бұрын
Hi mate, what throttle cable are you running? I need one exactly the same for my A body with the same QFT carb and throttle bracket
@prior8t2000
2 жыл бұрын
I have a quick question about getting your Truck on to a great start in the morning...??.. I think a Remote Transmitter Function Starter unit would work well for you.. Jus my thoughts and two cents..
@HeadFlowInc
3 жыл бұрын
The cam is at least the 284 Purple shaft. It may even be bigger…
@rustbeltbuilds
3 жыл бұрын
Bingo
@dylanschutt8565
2 жыл бұрын
What cam? What are your power components
@rustbeltbuilds
2 жыл бұрын
Mopar purple stick cam. “J” Chrysler heads. Intake. Carb. MSD ignition and headers
@gtgodbear6320
2 жыл бұрын
I hate the fact that my neighbor has to wake up at 5:30am and come home at 6:15am. I'm not sure what engine and exhaust he has in that Dakota Sport Magnum 4-door but it does sound beautifully, throaty but not too obnoxiously loud. Could even be a stock exhaust with a perfect leak somewhere. It actually sounds very good even though it wakes me twice in 45 minutes. I wonder what he's doing every morning?
@Greasemonkey05
Жыл бұрын
That cam kinda sounds like a shitty starter 🤣 Jk, Sounds awesome my dude.
@LifewithMario44
Жыл бұрын
Sounds good what cam are you running
@americanmusclemaniac9565
2 жыл бұрын
Hey man can I use this video for my KZitem channel. I will credit you.
@rustbeltbuilds
2 жыл бұрын
Go ahead
@americanmusclemaniac9565
2 жыл бұрын
@@rustbeltbuilds thanks
@MichaelBrown-um8qc
3 жыл бұрын
780cfm vac, max 👍😊 for that combo & that's a touch big.
@callmecraft3809
Жыл бұрын
This video is addicting. I find myself watching it every week. It sounds so good.
@rustbeltbuilds
Жыл бұрын
The Camaro on our channel sounds better!!
@marshallmcdowell3369
5 ай бұрын
Sounds great! I had a 1978 ford truck with a 351M and a cam and head work done to it. Takes me back to firing it up on a cold morning
@55GallonTrashCan
Жыл бұрын
you can hear the horses' galloping.
@christianandrews1328
Жыл бұрын
Cam specs plz
@MichaelBrown-um8qc
3 жыл бұрын
OMG !! I put a 68 trani in my r&r for that grani gear hole shot. .
@SmallBlockTrevy
3 жыл бұрын
Everyone give him a sub that has commented. Help his channel grown in my small town 🤙🏻
@Carl_Jr
Жыл бұрын
There's no such thing as a carburetor that's too big. Only engines that are too small! 😎👍🏁
@jaivokid82
Жыл бұрын
what brand and type of cam did you put on it?
@brianwarner6121
2 жыл бұрын
Sadly the can isn't making it start hard, the fuel drain back is the culprit, notorious for dodge mechanical pumps, but it sounds nice.
@zachlindley1145
2 жыл бұрын
What cam exists that would produce a similar sounding idle for these engines? I'm building one for the first time and don't know what I should look for
@rustbeltbuilds
2 жыл бұрын
If you scroll through the comments on this video I think I listed the cam for this engine
@elektro3000
2 жыл бұрын
Love that cam! What compression does that work out to with the police heads?
@rustbeltbuilds
2 жыл бұрын
Somewhere around 9.1 I’d guess
@gunwalepffp8545
7 ай бұрын
bad ass. i bet you are not invited to neighborhood cookouts.
@tomfletcher3817
2 жыл бұрын
Super 10's vertical
@sorianolopez3145
Жыл бұрын
Sounds amazing 😍💓💓
@gprich82
Жыл бұрын
Badass
@sammyprestwood3182
2 жыл бұрын
A 600 Holley carburetor would have been big enough for that 360 I know I've been there done that
@rustbeltbuilds
2 жыл бұрын
Indeed
@68chargercrazy
3 жыл бұрын
I love small block Mopar
@68chargercrazy
3 жыл бұрын
The 318 mopar has fewer factory returns than any other engine built in the USA
@TheAyrman
Жыл бұрын
Wish I knew what cam this is to put in my truck. Sounds great
@rustbeltbuilds
Жыл бұрын
Not sure if specs or part number anymore
@fernandogrijalva9091
2 жыл бұрын
Sandin Racing Hermosillo Sonora México 👍
@popwarner8029
2 жыл бұрын
I found out the hard way that you better have enough compression to go with that Big cam. Otherwise it will be a Dog
@rustbeltbuilds
2 жыл бұрын
It could use more compression for sure
@rustbeltbuilds
2 жыл бұрын
Think it’s around 9-1
@Sly9192
2 жыл бұрын
Slow start, strong finish
@Schlipperschlopper
3 жыл бұрын
Sadly from 2030 on all combustion cars including classics will be banned from public streets in entire EU and Scandinavia :-( In Germany the Green Peoples Party gave order to shorten fuel supply from 2025 on by reducing all conventional fuel stations to only one state operated central gas station per city or county. Now they want to slow down all the gas station fuel pumps from 20 litre per minute to 2 litre per minute...From 2027 on in the EU certain car spare parts will be banned too....as exhaust systems, turbo chargers and even some engine and gearbox oils...California and New York will do the same from 2027 on.... So no investments should be done in oil burning cars any longer....They even created a new kind of crime here, called emissions and smoke crime.
@rustbeltbuilds
3 жыл бұрын
Wow thanks for that news. Can’t believe that
@thelastrebelshow1627
6 ай бұрын
Nice truck bro. I have a 1990 D 150 all original except the paint I painted its Satin black.
@PatandDoopypoopy
Жыл бұрын
Something we used to do back in the day was prevent the engine from starting until oil pressure built to minimum, usually 20 psi. Cool video man. I just like old-school engines with thumpy camshafts
@rustbeltbuilds
Жыл бұрын
Check out our recent videos!!
@MrRatkilr
11 ай бұрын
Starting in neutral helps the torqueflite trans last longer. Imo
@forsale313
2 жыл бұрын
Which one "pops" louder, That thing on the seat or those pipes on the side?
@rustbeltbuilds
2 жыл бұрын
Definitely the pipes, check out the dodge burnout video for proof lol
@matthewpetersen4417
2 жыл бұрын
there's a reason we run a double carb spring. But awesome
@ra7538
2 жыл бұрын
Damn that thing sounds awesome.
@MendezE68
2 жыл бұрын
Q vonito frente
@billflk2364
3 жыл бұрын
Need to adjust your timing and then it'll start right
@Aidan-uf9bc
2 ай бұрын
He just said it’s been sitting for two weeks
@blackvan84
10 ай бұрын
Nice cam any clue on what it is
@wesleynash9385
2 жыл бұрын
Wish my 75 D300 souned like his 😍
@josephsaucedo8691
3 жыл бұрын
Sweat truck it looks clean no rust or any big dents. dawn dodge starter always sounds week even when there new. Like the rims 👌👍✌️💯🥂
@vicdevdanjoh5928
2 жыл бұрын
Get a starter from a second gen dodge with a 318 or 360...there half the size and turnover a million times faster...just put on from a 98 in my 83
@josephsaucedo8691
2 жыл бұрын
@@vicdevdanjoh5928 thanks for the tip I have a 84 ramcharger and 76 power wagon, 67sports fury 👍👌✌️💯🥂 it's Mopar or no car
@vicdevdanjoh5928
2 жыл бұрын
@@josephsaucedo8691 hell yeah brother mopar or no car...in currently putting a built 440 big block mopar in a 84 ford Broncos 2 lol...should be 500hp when it's done
@josephsaucedo8691
2 жыл бұрын
@@vicdevdanjoh5928 I wish my 67 sports fury Had 500hp that would be one sweat 6 pack. Good stuff have a great one till the next one 👍👌✌️🥂💯
@vicdevdanjoh5928
2 жыл бұрын
@@josephsaucedo8691 check out bearded boggers on KZitem to see my 84 power wagon...keep the rubberside down buddy have a good one
@AntonioPerez-hv1lp
Жыл бұрын
😐😁
@blackvan84
Жыл бұрын
What cam love the sound
@RustOnWheels
Жыл бұрын
My first car was a 1976 W200 with open pipe. It didn’t sound as wild, more like a tug boat with the original 318, but it was a flat black work truck not unlike this one.
@iconofsin5886
6 ай бұрын
This is thing is high strung.
@kiyoshi8657
3 жыл бұрын
So many hot heads already in the comments telling him how to enjoy HIS car. lol Awesome 360, I have one in my 64 valiant and love hearing how you have this set up
@rustbeltbuilds
3 жыл бұрын
Thanks! Love valiants!
@leotomma3494
3 жыл бұрын
And these hot heads down know what they're talking about
@throttleblipsntwistedgrips1992
3 жыл бұрын
Nobody's really telling him how to enjoy his car everybody simply telling him that his carb is too big, which it is. Even a cam with over .500 lift and 250 duration won't require more than a 750, LA heads are just that restrictive. Even with a 340 or magnum head swap and headers you still have a 1.6-1.9 inch exhaust valve to compete with as well as very small ports.
@kiyoshi8657
3 жыл бұрын
@@throttleblipsntwistedgrips1992 awesome reply and neat info!
@thebaldseagul1009
Жыл бұрын
You arent out of the dmv area are you. There was a badass repurposed valiant taxi with a loud ass motor. Ive been trying to buy that off that guy
@longsleevethong1457
2 жыл бұрын
More chop than chop suey
@supermopar7497
2 жыл бұрын
Definitely to big carb, & cam. A motor that I would have built when I was 13.
@fernandogrijalva9091
2 жыл бұрын
My too like it the sound
@JoeBordy-e5f
Жыл бұрын
Throw j heads away, therea ao many better heads out now the old mopar heads are as good as a door stop. I wont even mess with factory heads anymore regardless my budgets
@stevodakine1
Жыл бұрын
Sounds like a boat
@sqwidship
3 жыл бұрын
sounds like a whiplash cam
@thatnookdude320
Ай бұрын
Van Halen would be proud
@gilbdaregulater
3 жыл бұрын
My goodness sounds a band performance
@Aidan-uf9bc
3 ай бұрын
Neighborhood loves this guy
@NialPowerCork
2 жыл бұрын
Oooh she bad!!
@road2richz_q266
Жыл бұрын
Definitely sounds pretty good, Your timing is off, shouldn't took that long to fire up
@UG_Viper
2 жыл бұрын
who else hears beautiful people from this cam?
@UG_Viper
2 жыл бұрын
referring to the part where he is at the engine bay
@rustbeltbuilds
2 жыл бұрын
Someone commented the same thing!!
@roachcoachhelis6387
2 жыл бұрын
Sounds healthy👍
@tomkaufman3914
3 жыл бұрын
Full 1/4 race cam fuel starving and running fat,you might wanna get an electric fuel pump asap.
@monkeyCmonkeyDoo
3 жыл бұрын
What?
@throttleblipsntwistedgrips1992
3 жыл бұрын
Nah fam, just re-jet it and do it right. 7psi for a carburator is plenty. Electrics run waaaay more than that, so swapping to an electric pump, and regulator, vs a quick jet change, I know what I'd pick.
@charlesdiffenderfer8603
Жыл бұрын
Sounds really good 👍
@rustbeltbuilds
Жыл бұрын
The Camaro on our channel sounds better
@marcojimenez9068
2 жыл бұрын
Sounds wonderful
@jasonwilson1677
2 жыл бұрын
My van needs that cam
@chriszablocki2460
2 жыл бұрын
Old carbourated mopar engines are male. You couldn't name your truck Jennifer in good conscience. What kind of revolver is that?
@rustbeltbuilds
2 жыл бұрын
1944 S&W service pistol
@chriszablocki2460
2 жыл бұрын
@@rustbeltbuilds you're classy on a whole other level. I've got a B250 van that needs a lot of work and carry glocks.
@rustbeltbuilds
2 жыл бұрын
I carry a Glock everyday !
@grizly_27
2 жыл бұрын
Awesome sound!!! 🤟🏻
@kylecalloway9931
3 жыл бұрын
Hey what kind of cam if you dont mind me ask
@toadsmushroom
Жыл бұрын
Delicious
@zrksi
11 ай бұрын
trying to get my slant 6 to sound like that LMAO
@brandonzigler5239
7 ай бұрын
I need this cam but i cant find a cam for a 360 anywhere. If someone can help i would greatly appreciate it
@cordburns6075
Жыл бұрын
Nice truck
@rustbeltbuilds
Жыл бұрын
Check out our recent videos
@GoombsGarage
Ай бұрын
Really wish I knew what cam that was or at least the specs it’s exactly what I’m looking for
@MrWhitcomb97
2 жыл бұрын
MERICA! 🇺🇸
@citizene3120
3 жыл бұрын
You have to pump the carburetor like 5 times and it will start super easy fella
@chewy-bu1oy
2 жыл бұрын
Where did u find the headers if u don't mind me asking I'm getting ready to rebuild my dodge 360 and was wanting to put headers on it
@rustbeltbuilds
2 жыл бұрын
I’m sure there on Jegs or online somewhere
@chewy-bu1oy
2 жыл бұрын
@@rustbeltbuilds ya iv looked around for a set but iv also been told that some of the sets that they sale for these old truck won't fit because of the frame iv already did the newer dodge starter upgrade so it don't have that big starter anymore but that's why I asked a few people have told me I have to watch witch ones I buy being some of them won't fit because of the frame
@rustbeltbuilds
2 жыл бұрын
@@chewy-bu1oy I understand, I think I’d do research and buy a set for the old trucks and if they don’t fit, take them back and try another company. Doug Thorley, hooker headers. Those are the best brands out there. They might have direct fit
@chewy-bu1oy
2 жыл бұрын
@@rustbeltbuilds okay iv been looking I'm about to build the engine in my 85 d350 after I get the rest of the parts
@tl5108
2 жыл бұрын
@@chewy-bu1oy I love my hedman hedders didn’t can slip them on and off just by jacking the truck up enough. Use a ball and socket connection down at the collector so you don’t have to worry about a gasket there. Just get a nice thick graphite gasket to seal at the manifold. Remflex makes some really nice ones
Пікірлер: 291