Man, thank you so much! You're a GREAT teacher and taught me A LOT!!! You explained the software perfectly.
@markgarza100
10 жыл бұрын
just installed a pc5 and my question is when you turn the key and flip the cut off switch should it flash red and green then turn off. When I start the bike it says green
@dynaguy209
6 жыл бұрын
Shit send me straight to snowmobile maps. Can not find Harley maps anywhere on this website
@flesh199
9 жыл бұрын
Thx a lot for this video.almost no one talk about 2 stroke sled tuning!
@Mihalyofficial
4 жыл бұрын
Why would you adjust the low mid and high rpms? Im using fc and when i initially start the bike the rpms are very low is this normal? Thx.
@jacobwerner99
11 жыл бұрын
i put a pcv in my cbr1000rr and with the m16-002-007 map i have a LOT of trouble at low revs ....... any advise???
@bricehoogenboom6483
6 жыл бұрын
Good basic vid. I learned the hard way about quick throttle adjustments and autotune. Just as you stated. Kept getting richer and richer on my part throttle blocks, so going through trails it was loading up horribly. My question is a bit more advanced. Would you suggest pulling any timing with boost? I'm only running 5-6 lbs on an Apex. I'd rather not blow it up, but 5 psi isn't much. I'm just not sure how advanced stock timing is.
@joe9alvarado1
5 жыл бұрын
I just checked and only see maps for ATVs and Snomobiles
@veetwotls
7 жыл бұрын
were can i get a map for 2014 KTM 690 Enduro R - mods: pipe , filter & rally cam
@GeryRevandra
9 жыл бұрын
hi , pardon my question ... about map , did you installed map into PC5 before installed into bike or installed map into bike after installed into bike ??! ...
@json216
5 жыл бұрын
Will a auto tune unit be just as good as getting a dyno tune..without the auto tune unit
@dongm6596
11 жыл бұрын
I have a pcv and zbomb on my 2011 cbr1000rr.. How will adjust my a/f to compensate with the zbomb?
@apollombuki2602
10 жыл бұрын
where do i get pcv maps for drf250r? download link
@notone4029
10 жыл бұрын
Thanks ALOT for taking the time to go through everything with setting up the PCV . I just purchased a almost brand new one for my GSXR 750 but came with everything including stickers EXCEPT setup directions. So your tutorial helped GREATLY. Thanks
@ToughtPolskia
7 жыл бұрын
I just got one too. Questiong though. How did running a default map work for you? Did you have any trouble with that? Did you actually dyno tune it?
@tariqholder8818
10 жыл бұрын
U r da man!.. gr8 vid .. gr8 advise, step by step tuturiol.. thks alot..
@jacobwerner99
11 жыл бұрын
do you have pcv maps for cbr1000rr i didnt see them ?
@takdirfairus4803
8 жыл бұрын
where is i can get mapping for MT25 ? thanks
@GunfighterBo
11 жыл бұрын
Thanks that helped me a lot the instructions included were really Vague !!
@joe1340busa
11 жыл бұрын
Hi does it use a mini Usb to Usb like PCM 3usb ?
@MRSBA7
11 жыл бұрын
Great video. i do have an issue, if you can help me.. i tried to send a map to my bike (zx7-with Leo Vince full exhaust) but it says Error sending the map.. it seems it can only recieve *.map (i have a pc III) but the map files in dynojet are *.djm ... what can i do? where can i find the *.mpa files? thanks!, again Great video, thumbs up.
@Pete3Heat
4 жыл бұрын
Cause youre trying to send a PC 5 map to a PC3
@TheXilentWifi
7 жыл бұрын
Great video, THANKYOU
@JoeyStrub
11 жыл бұрын
do you have a early PC3 non USB?
@BLINC606
7 жыл бұрын
how do i get / make a "zero" map? or all stock basically as in the power commander isn't even there and is making no changes. i have a 2015 raptor 700. thanks in advance
@BikemanPerformance
7 жыл бұрын
Highlight all the cells and change the values to zero. This means that the PCV is not adding nor removing fuel from the stock mapping.
@BLINC606
7 жыл бұрын
BikemanPerformance did that and it still wasn't running like stock. i just took the PCV off and problem solved. i'll try it again when my Yoshi comes in.
@infamouskillas
11 жыл бұрын
wanted to say great tutorial with the autotune portion. thanks for all the advice.
@31acruz
9 жыл бұрын
Dude ..... You keep lighting up rows and columns yet you don't bother to tell us, show us where you are clicking to do that?? Nice for you that you know where to click and how, but we don't.
@Thelemorf
8 жыл бұрын
+31acruz Dude... have you ever used a fucking computer before?
Пікірлер: 35