Easiest/shortest demo video I've seen for this unit, thanks!
@Psychomantis619
Жыл бұрын
Sir, thank you kindly. First video of Binks pressure pots that helped me. All I can say watch plenty of them. You will walk out with alot of tips and tricks.
@jamieargyelan292
Жыл бұрын
Glad I could help
@eastbaygrease10
3 жыл бұрын
Great explanation. I've been discharging wrong!
@juanjimenez9894
2 жыл бұрын
EXCELLENT DEMONSTRATION !!!! THANK YOU !!
@randywl8925
Жыл бұрын
Clean and simple 👍
@juancarlosespana7366
5 жыл бұрын
Very useful video,I use those type of pressure pots a lot
@jamieargyelan292
5 жыл бұрын
Juan carlos España let me know if I can help with anything
@war3405
4 жыл бұрын
Great video My question is : What is the maximum length hose I can conect from my compressor to that pressure pot and then what is the maximum length of the hoses on fluid and air automation Thank you
@ShukokaiStu
4 жыл бұрын
Very well explained thank you. 👍
@miguelsontay280
2 жыл бұрын
thanks for the tips i got the same unit
@jayhillyer2542
3 жыл бұрын
This was great
@ljazguyudig1
4 жыл бұрын
I have a question. But first off. Thanks for the video, it helped me out. Theres an outlet that comes out the top. Where does it go
@jamieargyelan292
4 жыл бұрын
Louis Jaramillo There’s only one outlet for fluid out to the paint applicator. And one inlet that Pressurizes the pot. There’s also a pressure relief that you can turn that will release the pressure to make it safe for opening
@davidavidquintanilla
5 жыл бұрын
thank you
@tonymarazzo289
11 ай бұрын
I'm pushing laytex and I'm getting air in the line. I don't see where it's coming from. Thoughts?
@jamieargyelan292
11 ай бұрын
Make sure the lid seal is good and clean. The pressure side shouldn’t exceed 60 lbs.
@KennethPWise
13 күн бұрын
Where can I get replacement regulator gauges?
@jamieargyelan292
13 күн бұрын
@@KennethPWise let me know what part of the country you are in and I will help you with a local distributor
@jamieargyelan292
13 күн бұрын
@@KennethPWise let me know what part of the country you’re in and I will set you up with a local distributor
@Garcia90026
11 ай бұрын
Whats the difference between the gray and black hose ?
@jamieargyelan292
11 ай бұрын
Gray hoses for air black hose is for fluid
@Buggy0106
Жыл бұрын
What is the maximum pressure you push from your air compressor to the pot?
@jamieargyelan292
Жыл бұрын
If you have a dual regulated pressure pot as shown in the video, you can bring full line pressure to the pressure pot. 125psi max
@jayhillyer2542
3 жыл бұрын
Do you have any compressor recommendations for this Bink model?
@jamieargyelan292
3 жыл бұрын
Something that will give 30 cfm at 90 psi maybe a DAD-500 at the point of use.
@jayhillyer2542
3 жыл бұрын
@@jamieargyelan292 Thanks for the response! I'll be using it for resin casting, so no paint. The mid range ones that are being thrown out in forums have much smaller cfm, like 2 (see link to a makita). Is one this small (theres a 3 gallon variant I assume bring it to about 3 CFM) viable? kzitem.info/news/bejne/joybz5enfp2hqag
@jayhillyer2542
3 жыл бұрын
The resins will work at 60 psi
@jamieargyelan292
3 жыл бұрын
You should always oversize your compressor. You do not want to work it at max.
@jayhillyer2542
3 жыл бұрын
@@jamieargyelan292 Thank you!
@valentinolmos7982
3 жыл бұрын
Why it has to be grounded?
@jamieargyelan292
3 жыл бұрын
If it’s solvent-based pain and you create a static charge you could ignite the paint. Good practice to ground everything in the paint area
Пікірлер: 33