Does this put constant pressure on the spring? If so the problem with that is the spring will slowly loose it’s extra power, you guys should release a new spring instead. Great idea but in the long term it might not be good for your spring. People have gotten better springs for guns like the Texan in the past and I have seen them for like 10$, I don’t know if that will fit in this gun, but it shouldn’t be hard for you guys to get a stronger spring in the future. Also a new spring would allow you to go all the way up to 4500psi instead of 4000, you should release 2 diffrent springs, one that shoots at 4000psi for people with external regulators, and one that can do 4500psi for everyone else, also does anybody know if there are problems with hammer bounce?
@wildrangeringreen
Жыл бұрын
it just adds to the preload, doesn't really hurt the springs, since they are still not being fully compressed even with the washers. Using a lighter spring, and being able to add preload is far better for a MFG, since it's just one part, and you can modify the gun to have to output you want. In a way, it's no different than adding and subtracting washers from regulators. Personally, I don't understand why people are still wanting to beat their guns to death with powerful springs and heavy hammers in order to get a little power lol, there've been better designs out in the hobby-building world for nearly 20 years lol.
@Scott-cu4ol
2 жыл бұрын
Not sure there is a big benefit to adding the 3 washers. stock seems pretty good for a 9 mm 🤷🏻♂️
@mjeff7415
2 жыл бұрын
facts 💯 I don't see any difference either.
@mikem602
2 жыл бұрын
7 shots over 917 fps with washers and 3 shots over 917 without. Not a gigantic difference but seemed to help.
@swingonthespiral
2 жыл бұрын
@@mikem602 That's very good imo. But the thing is for me, .357 slugs dont like 917 fps. Pellets can take it, but most slugs like mid 800s or high 900s.
@99prochargedbird85
2 жыл бұрын
@@swingonthespiral Come on they have slugs shooting well over 1000 fps with accuracy on air and with helium well beyond that. There are so many slugs styles and grains to choose from. Pellets are old technology and been around since the early 1900's, and JSB Diabolo pellet started in 1991, and for .357 cal you have one 81.02 grain to choose. Slugs have much higher BC (Ballistic coefficient) than any diabolo Pellet. Pellets will shoot fast at first, but slow down fast because of the drag low BC of the pellet.
@stephenrosenthal5252
2 жыл бұрын
It averaged 50 fps more. That's a great gain for an airgun, for a basically free mod. And a reversible one at that. I have found that with airguns. And I am not an expert. But have quite a few. That it is often a sum of the parts. One mod might only do small gain by itself, but then with another mod it is like the gains are multiplied. Idk? I think it's a great little mod!
@Bigbopperairguns
2 жыл бұрын
I can’t weight for the new kit coming out!
@Bigbopperairguns
2 жыл бұрын
I don’t under stand why this did not help because it added over 70 FPE to my 457 Challenger.. But I used 4 washers. I guess I’m lucky I have hade no problem with 4 washers.
@Bigbopperairguns
8 ай бұрын
3 years later and no problems 😊
@jorgecetina1886
Жыл бұрын
Where do you get the washers?
@davidstephens6379
Жыл бұрын
All you done was add 800 psi from 3200 on the first string to 4000 on the second string of course when the hammer strikes the valve the shots with have more power because their is more pressure inside the tank adding the three washers only make the valve stay open longer this can be achieved by getting a heavier spring
@jbhk7977
Жыл бұрын
By adding more pressure in the tank you take away the "added value" of increasing the spring preload because your valve dwell time decreases.
@SkutsiPena
4 ай бұрын
thats bs, if you up the fill pressure on non regulated gun and dont stiffen the spring or add weight to hammer the velocities will go down untill sweet spot because the hammer dont have enough kinetic energy to open valve as much as lower fill pressures.
@blakelambert3971
2 жыл бұрын
Great info 🇺🇸
@jimfitzgibbon5492
26 күн бұрын
How thick is each washer?
@morrisvannieuwendam1320
2 жыл бұрын
Hi Bin, how thick are these washers?
@kibonge61
2 жыл бұрын
I would just go for 1 mm washers add 3 see if it still cocks and catches on the sear.i want to know the ID and OD of washers though.
@crypto_creep8222
2 жыл бұрын
The gun ckearly has a horrible tune. 😕
@kashimiakimokato1017
2 жыл бұрын
报哥,微博上咋个内容少了,给是被限制了嘎
@carlosreyes5835
Жыл бұрын
What distance can this gun get that’s good for hunting?
@sagemajka4871
Жыл бұрын
Bin Tac, I never received my washer power kit, for my Big 9, that I pre ordered, when it came out. You said you were going to ship them to me, this last summer, but I never received them. Can I just purchase them? I would really like to have them.
@sigshooter6213
Жыл бұрын
Just contact us directly
@jazuluss
2 жыл бұрын
Any news on a 357 in semi auto and short barrel or pistol?
@choumantw
2 жыл бұрын
請問AEA折疊槍托可以改固定托,要用什麼規格
@mjohnsmith9529
Жыл бұрын
What size should washer be ? Thickness
@tedshickell7315
7 ай бұрын
Who do I get in contact with to buy this stuff
@sigshooter6213
7 ай бұрын
BinTacllc.com
@user-kn3ru6vi6o
2 жыл бұрын
請問該如何把我的aea assassin635變更快,使用2.5g喇叭蛋,只能跑230初速而已
@marksun6247
2 жыл бұрын
will these washers work for 35 and 50 cal, challenger bullpup? have owned it for 2 months.
@sigshooter6213
2 жыл бұрын
Yep my friend works for all big bore only
@lindseyzacek5211
Жыл бұрын
How is the 50 caliber Challenger I'm thinking about buying it this week
@xinyang6200
2 жыл бұрын
好久没看报锅了 是从什么时候开始全英文节目了?好像评论区也全是英文朋友了…
@lindeshen80
2 жыл бұрын
报哥是官司缠身 没看一把火器都没有了么?本来要坐牢的 估计破财消灾了
@plove9136
2 жыл бұрын
We are the consumers of Bins product.
@catherineharris4746
2 жыл бұрын
@@plove9136 FACTS!😂👍👍👍
@kdaniels1172
2 жыл бұрын
Hey is there a way to decock the new ssmax 35?
@plove9136
2 жыл бұрын
He has a vid. That shows you.
@plove9136
2 жыл бұрын
How is it? I have a 25carbine with carbon fiber bottle. Frekn love it.
Пікірлер: 46