I have been a carpenter and cabinet maker for over 50 years, what a treat to see a nail forged. All these years I have taken nails for granted, buy a couple pounds of them, waste a few from misplaced blows of the hammer, tear something down to remodel and throw a few out with the trash, it didn't seem to matter. I recently pulled a few shelf supports out of an antique cabinet from my father's old radio shop and found them attached with hand wrought nails, I saved them knowing that they had value. Thank you for reminding me to find those nails and attach them to a backing and frame them for display in my shop.
@torbjornahman
5 жыл бұрын
Great!
@1musicsearcher
10 жыл бұрын
No wonder they used to burn the cabin down to save the nails. Great video.
@johnstewart9237
6 жыл бұрын
1musicsearcher And they had to make the iron!
@HooyahWaffles
5 жыл бұрын
Actually a myth
@guesty3843
3 жыл бұрын
oh
@fourgedmushrooms5958
4 ай бұрын
Nailed it! Love the super light tool.
@Lesardah
9 жыл бұрын
Thank you for spending so much time to share your craft! The smithing is awesome enough, but putting it together so well on camera - amazing. I loved watching the work that went into laying down the new power hammer, too. The way you made the replaceable bolts was brilliant. If everyone built things with an eye toward their future maintenance, maybe we wouldn't live in such a throwaway culture.
@torbjornahman
9 жыл бұрын
Lesardah Thank you!
@andrewconway5979
4 жыл бұрын
My great great great grandmother was a nail maker from the age of twelve until she was in her forties. I wonder how many nails she made in her lifetime? Probably a million or so.
@jonathanmoothart8038
3 жыл бұрын
Wow! That's impressive!
@stevesyncox9893
2 жыл бұрын
Avg was 60 an hour.
@stevesyncox9893
2 жыл бұрын
120k a year, x 30 ish yrs, 3.6M ish... 40 hrs a week.
@andrewconway5979
2 жыл бұрын
@@stevesyncox9893 She was probably working 70+ hours a week. Nail making was a brutally tough business in the industrial revolution.
@ericd468
3 жыл бұрын
Wish I'd watched this years ago--I didn't know about bending the stock at the cut to keep the point out of the fire while heating the head. It's these little tricks which make the technique work well! Thanks!
@xxoozzcici13
4 жыл бұрын
Thanks for making this video five and half years ago. I just found it and love it. I'm a metal detectorist and I find old square nails and have always wondered what goes into making them. Thanks again.
@torbjornahman
4 жыл бұрын
Cool!
@sdk58
2 жыл бұрын
Same. I'm hunting an area now that must have been a blacksmith shop during the Civil War.
@meganerd14
9 жыл бұрын
Really wish I learned this in high school. Thanks for the vid bro
@cubiusblockus3973
9 жыл бұрын
MN-14 never too late to start.
@Keith_Ward
9 жыл бұрын
MN-14 Look around for local blacksmith's or local organizations that help promote blacksmithing. They love to show others how to do these things and keep it going.
@patman0250
5 жыл бұрын
You still can never to late for a new skill..
@Lemev
Жыл бұрын
One of the best finished nails I've seen, lots of skill... thanks for posting!
@Eisen_Jaeger
5 жыл бұрын
You made that seem so easy. One of the best examples I've see.
@michaelclark2840
9 жыл бұрын
I like your way of drawing out the nail on the edge of the anvil. Very neat and controlled.
@PopsShack
6 жыл бұрын
Very nice work. From the apparent ease with which you did this, it appears that in days of old, this would have been the job of the apprentices.
@FamilyForge
Жыл бұрын
Your channel is definitely one of my favorites. I’m learning blacksmithing from my dad and just did my first ever project which was, of course, nails. Took 20 heats but didn’t turn out too bad! I’m documenting the learning process on my channel. Now off to forge lot’s more nails and continue to improve!
@torbjornahman
Жыл бұрын
Cool, thanks and good luck!
@Lemev
Жыл бұрын
I've just watched your channel, Clara! Thanks for sharing your learning process.... your father has serious skills, he made that nail looks so easy, and the final result is outstanding!
@pedrohenriquemenegollitama909
4 жыл бұрын
all the work, all the adjetives one puts into his product makes the house a work of art
@scottsalgren2024
7 жыл бұрын
That was a simple demonstration. Not everything has to be extravagant with lots of steps and detail. Thank you.
@torbjornahman
7 жыл бұрын
Thanks
@pokeymjt
6 жыл бұрын
the take a few moments to make, but I love the "old fashioned" look!
@ninayasmijn
Жыл бұрын
this is such a nice video! i love how clear it shows every step, and how much craftmanship goes into it! this video was used in one of my archaeology classes to show us the process of how nails are made, and it made me so interested in blacksmithing! thank you for making this video and sharing it! it is very useful for us to analyse the nail we are given to describe including production process traces :)
@torbjornahman
Жыл бұрын
Cool! Thank you Nina!
@Cnctrldotcom
10 жыл бұрын
Great video, thanks. Over the last few years doing up our old house I've seen a lot of hand forged nails. Nearly all the one's I've been dealing with have been headless though as they were used for floorboards. I imagine making a few nails is quite enjoyable but making them day in day out must have been a hard life.
@torbjornahman
10 жыл бұрын
CNCtrl Thanks! Yes, everything was hard work back then. It's staggering when you realize how much work was put into everything...
@johnterrett4035
10 жыл бұрын
Brilliant video once again. Thank you Torb. Your nail header is a piece of art on its own. Looking forward to your next one!!
@patman0250
5 жыл бұрын
Now that's a nail!! I can watch this all day.
@schlaznger8049
7 жыл бұрын
That's cool, I was wondering how you were going to make the head. That's a nice little jig.
@jimbohotep
10 жыл бұрын
Great video , best one I've seen on nails yet ! Thanks
@KoyasuNoBara
6 жыл бұрын
Thank you! I'm reading a series of books where this one character is a blacksmith, and I didn't quite understand part of the description of how she made the nail. Once I actually saw you using the nail header, everything made sense.
@torbjornahman
6 жыл бұрын
Ok, great!
@FrancescPunsola
4 жыл бұрын
Very clever movements!, Its a pleasure watch how expert hands build them.
@resonanttotality8322
8 жыл бұрын
Always a treat to watch. You nailed it!.......... um....... I'll just go now.....
@viviansudhir3089
7 жыл бұрын
Very nice demo.Thanks for showing the way to make nails.
@torbjornahman
7 жыл бұрын
Thanks
@kennyb0y1597
9 жыл бұрын
one down 99999 left to go
@viv1847
5 жыл бұрын
with my last name bein Naylor (derived from ‘Nailer’, aka a nail smith) i found this video to be interesting in that it’s p much like what my fam of a long long time ago would be doing :^) not a job to be underestimated or brushed off! who made the nails that have kept historic buildings pieced together for all these years? nailsmiths!
@crashwelder5337
6 жыл бұрын
nicely done. that is a nice tool for forging the head.
@thedavidwalker
4 жыл бұрын
What hood and exhaust are you using? It looks like it works extremely well! I’m also curious about how you made the nail head tool. What size is the square, and how did you make it? Thanks for such a great video!
@torbjornahman
4 жыл бұрын
The header is here - kzitem.info/news/bejne/sqavmJavcpuXa3Y
@MorkSD
10 жыл бұрын
Nailed it ;)
@NocturnalNick
7 жыл бұрын
You, Sir, are the one, who in fact, nail'd it
@tonyprima7777
7 жыл бұрын
Torbjorn I already told you but would like to emphasize it again, impressive talent, excellent quality hand work!
@torbjornahman
7 жыл бұрын
;) Thanks!
@ПрокопенковАлександр-в6б
4 жыл бұрын
Как всегда прекрасное видео,с 3 минуты-романтическая изюминка.
@yelkeew
10 жыл бұрын
I'd always heard the reason early building methods relied on pegs/dowels instead of nails was due to the expense of nails. I never really thought about what went into making nails in pre-mechanized production, but now I completely understand the expense. That's quite a bit of work for a single nail. That was a good video and a nice product you forged as well.
@torbjornahman
10 жыл бұрын
Indeed. Thank you.
@beammeupscotty1955
9 жыл бұрын
I have only just recently subscribed to your channel and am slowly working my way through your videos. Aside from the fact that you make a very solid and attractive nail, (among other things) I noticed that while forging the nail you work with the anvil in the opposite orientation than I do, and which I have been led to believe is the norm. Your radius edge is on the near side while I have always forged with the horn left and the radius on the far side. I can, however, very clearly see the advantage, at least with nail making, of having the radius on the near side and drawing out on the near side, as that makes forming that shoulder pretty easy. That shoulder appears to be what makes it possible to forge that nice thick and symmetrical head. Although I already said it on the fireplace tongs comments, let me reiterate how great I think your videos are. They are probably the best instructional videos on youtube, at least for someone like myself who already has some experience under his belt. I have been banging away, mostly on my own, for the better part of 23 years, though because I do not have very extensive formal training, I have probably advanced my skill set much less than one might expect during that time. Your videos are great for me because I already have the skills to execute this stuff, I just need to see the technique.
@torbjornahman
9 жыл бұрын
Scott Rich Thank you! The orientation of the anvil is mostly a personal thing. I work both ways if needed. With the horn to the right like this has one advantage and that is you can leave a hardy-tool in place when you work on something on the face without risk hurting your hand on it (if you're right handed). You should have radiused edges both on near and far. I had to grind down some damage to my edges so I have different radii at some odd places, but it works ok. I'm mostly self taught myself - I think the key is to challenge yourself with new projects and not to be afraid to fail. Failure is the best learning experience :) Keep banging!
@beammeupscotty1955
9 жыл бұрын
Torbjörn Åhman I was teaching a beginner's blacksmithing class this morning and before my student arrived, prompted by your videos, I put a radius on the near side of my anvil as well. I am going to start working on your near side drawing out technique in the next few weeks. In the last year or so I have started making bottle openers for craft beer drinkers here in the U.S. These are people who may spend as much as $20.00 U.S. on a single bottle of beer so $60.00 pr $70.00 bottle openers are not out of the question for them. I used the proceeds from a couple of beer festivals I sold at to purchase a brand new anvil, so I am fortunate to get to put radius's where ever I want them, rather than having to work around the damage done by previous owners. After having worked for the last 15 or so years on a 100 year old Peter Wright anvil, it is really a treat to be able to work on something with a flat face and good edges. Your anvil is in very good shape compared to my Peter Wright.
@torbjornahman
9 жыл бұрын
Scott Rich OK, nice!
@DulishusWaffle
10 жыл бұрын
That is a nice nail header design!
@ernst2674
10 жыл бұрын
Beautiful and very clear video! I tried is myself for the first time last Monday, it took me 5 hours to forge 18 nails......... :-)
@torbjornahman
10 жыл бұрын
Ernst Muskens Thanks! Good work and good experience. I bet the last ones went pretty smooth compared to the first...
@ernst2674
10 жыл бұрын
Torbjörn Åhman Yes indeed. And the biggest problems were to get the correct thickness of the nail and keeping the head of the nail in the 'middle' of the rest of the nail.
@torbjornahman
10 жыл бұрын
Ernst Muskens Yep centering the head is not easy, but on the other hand it doesn't matter much if it's a bit off. It's hand made after all.
@larryking606
5 жыл бұрын
Excellent Video , That is how a Blacksmith , makes a Nail ! Thank you for this Video ! Take Care and Keep Hammering !
@torbjornahman
5 жыл бұрын
Thanks Larry!
@synclavier123
5 жыл бұрын
I've seen a lot of your videos, but this is my favorite. :)
@torbjornahman
5 жыл бұрын
:) Thanks
@nightschoolblacksmith6219
7 жыл бұрын
Very precise and to the point. I shall be at this soon!!
@Itnecap
6 жыл бұрын
KZitem exists only for such finest videos.
@UnlicensedOkie
6 жыл бұрын
I work at at an old military fort historic site (1868-1894). We recently had winds take part of the roof off of one of our old historic buildings, built in 1892. From looking through the wreckage, I noticed all of the old original nails laying around everywhere. None of them had the round head, like yours. Could this have been because they just didn’t do that last step that you showed? All of the square cut nails I’ve seen had rectangular heads on them. Picking them up today, it made me curious of the process that goes into making these nails. I thank you for this lesson. I am subscribing and I plan on watching more of your content as well. Take care and keep up the good work.
@torbjornahman
6 жыл бұрын
Interesting. To me it sounds like early machine made nails! I think the actual term "cut nails" refer to just that.
@UnlicensedOkie
6 жыл бұрын
Torbjörn Åhman they look exactly the same as what you have here, just with square head You could be right and they are just machines nails I just referred to then as square cut regardless of if they are made this method or other lol.
@jameslouder
6 жыл бұрын
If the roof dated from 1892 then the nails were certainly cut-nails in the correct sense, i.e. nails that had been cut from sheet-stock (not bar or rod) by a mechanical shear, striking at an angle across the width of the sheet. This would give a nail with a rectangular section. If you have an example in good condition, feel the edges and along two of them will be a slight burr, from the stroke of the shear. Roofing nails would have a rectangular dog-leg head. For other uses different head-shapes were struck or die-formed.
@ProjecthappylifeNYC
6 жыл бұрын
Wow. I know I'm a few years late to watching this video, but I love your channel, and that nail and header turned out really nice!
@torbjornahman
6 жыл бұрын
Thank you! Never too late :)
@tompok76tompok76
5 жыл бұрын
Awesome work!
@klausreichert4139
3 жыл бұрын
Super Arbeit.....aber jetzt kann man sich vorstellen welch ein Aufwand es war im Mittelalter Nägel her zu stellen und eswegen nur sehr wenige verwendet wurden.....vielleicht gibt das einigen Leuten zu denken die mit Nägeln nur so um sich werfen, wenn ihr sie selbst machen müsstet !!
@JASON-BEAZLEY
Жыл бұрын
Love your videos
@FranciscoHernandez-jh9or
4 жыл бұрын
1:57 Swear to God I only hear jingle bell, when iron been hit.
@billsutherland2128
7 жыл бұрын
Beautiful work!
@bags4649
7 жыл бұрын
Thank you Bags from Australia
@ronsbeerreviewstools4361
6 жыл бұрын
Thanks for this interesting and informative video.
@PietroMaker
6 жыл бұрын
Hello from Italy, im your very fan , your work is very fantastic. Sorry for my language .
@torbjornahman
6 жыл бұрын
Thank you!
@captainsuperfly
8 жыл бұрын
Great demo, thank you.
@danielbennett8685
9 жыл бұрын
that was cool I have never seen a nail header
@joehoward2832
9 жыл бұрын
Nice job
@ricwol8273
7 жыл бұрын
I like this video . Some thing new to learn .
@casper1240
6 жыл бұрын
Great Demo thanks
@TheThor2745
4 жыл бұрын
Really good nail...
@WinDancerX
8 жыл бұрын
Thank you for this demo!
@seronymus
2 жыл бұрын
You have the most blacksmithy name I've ever seen.
@torbjornahman
2 жыл бұрын
:)
@guillermodietrich3629
2 жыл бұрын
My 7th and 8th gen great grandfathers were both Meister Nagelschmied. ⚒️
@torbjornahman
2 жыл бұрын
Cool!
@bleizucker3775
6 жыл бұрын
Thanks for teaching me.
@srbprod1
9 жыл бұрын
how much does your forge cost to maintain? by the way, your blacksmithing videos are really cool! i really like the leaf you made of metal
@torbjornahman
9 жыл бұрын
kib Thanks! Not much to maintain.... sure you have to buy coal, pay your power bill and buy some steel now and then. Haven't really calculated on it.
@Undercover42002
5 жыл бұрын
That's crazy, but still love finding those nails
@Prashantkumar-hv3md
6 жыл бұрын
I love this ,thank you so much.
@dadragonfireoutdoors5642
8 жыл бұрын
now Imagine a medevil blacksmith having to make a city's worth of nails. (hundreds per house)
@torbjornahman
8 жыл бұрын
Precious things :)
@chartle1
8 жыл бұрын
dadragonfire outdoors I recall watching a TV show and the smith was making nails. he couldn't be as efficient as he wanted to be since he only had the one hardy hole. but I think he said he would be expected to make some astronomical number like 1 every minute. is that even close?
@torbjornahman
8 жыл бұрын
It depends on the size of the nail of course but I have heard numbers of up to 100 nails / hour, by hand, back in the days...
@chartle1
8 жыл бұрын
One other thing I heard as you moved from frontier home to frontier home you burned down the old house to reclaim the nails.
@torbjornahman
8 жыл бұрын
Cliff Hartle Yes, I have heard the same thing, but I think that's a myth to some extent at least.
@tobiaswhittaker7462
8 жыл бұрын
fine job sir!
@kimfields9182
4 жыл бұрын
im satisfied of the noise
@TheStackeddeck77
3 жыл бұрын
Sorry if this is a dumb question, but what fuel are you using?
@torbjornahman
3 жыл бұрын
Here I'm using coal!
@juanacevedo3007
4 ай бұрын
Saludos desde Uruguay👏🏼👏🏼👏🏼
@HappyPappynKatyTX
10 жыл бұрын
Wish I had a hundred. Awesome for use and display
@brucedavis8736
6 жыл бұрын
that was fun to see . no bitching .no talking abut little Timmy's long day no wife rant in the back drop. and just the tools and things we needed to see Respect Brother. we could hang out for a week end buy the fire with hammer's and beer.
@torbjornahman
6 жыл бұрын
:) Thanks!
@greenteambc
6 жыл бұрын
"working as hard as a nailer" and "Hard as nails" also comes from this hard process of pounding nails.
@willbe3043
3 жыл бұрын
beautiful!
@rustyshacolfurd4581
7 жыл бұрын
i was honestly kinda disappointed when you didn't nail some wood at the end of the vid
@torbjornahman
7 жыл бұрын
:)
@vulcanhumor
5 жыл бұрын
Always wondered how they were made.
@alexonder1545
7 жыл бұрын
Nice job !!
@joaomatheusarantes6452
4 жыл бұрын
Nice demo. I'm just wondering how was the tool (or jig) made in the old times 🤔.... without any power tool.
@torbjornahman
4 жыл бұрын
No problem, it can be made in a much simpler way.
@markrussell910
9 жыл бұрын
Oh, is that what you were making. Thanks
@mathieudube1183
5 ай бұрын
What if I don't have the head tool? Could I use the straight face tongs to hold the nail and hammer the head there in the pritchel hole?
@torbjornahman
5 ай бұрын
Don't think that will work so good... make a simple tool, just drill a hole in a plate! It doesn't even need to be square, but it's pretty easy to drift a round hole square with a squared tapered bar.
@Boar.
9 жыл бұрын
Очень хороший учитель. Всегда его ролики смотрю.
@АндрейМедведев-к9к2ш
6 жыл бұрын
А он показывал как у него вытяжка горна устроена?
@kingdarkem
6 ай бұрын
Interesting....wondering if it can be done for bronze rather then iron.
@torbjornahman
6 ай бұрын
I guess so, but bronze is mostly forged cold and regularly annealed. Not sure hot to go about it
@Gerbrand_01
6 жыл бұрын
I am struggling to make the nail pointy. Do I have to hold the piece slightly higher or do I strike it at a slight angle?
@torbjornahman
6 жыл бұрын
You angle the hammer and angle the work against the anvil slightly. Work at the edge to avoid hitting the face of the anvil.
@Gerbrand_01
6 жыл бұрын
Thank you!
@JEE_13
10 жыл бұрын
Your videos are extremely interesting to me. Thanks for sharing your craft. I hope to get into blacksmithing as I am just getting back into woordworking. Handmade nails would go perfectly with a lot of my woodworking projects. Do you have any for sale? haha Thanks again, from Ohio, USA.
@torbjornahman
10 жыл бұрын
Jeff Eckelbarger Thanks! I could forge you some, but the shipping is probably pretty hefty. I bet you can find a blacksmith near you that can forge some nails for you.
@benjaminzedrine
6 жыл бұрын
That is a nice looking nail header, and how it fits into the pritchel nicely too. Spring steel header with mild steel handle?
@torbjornahman
6 жыл бұрын
Thanks! Yes, it's nice, as it keeps it still during heading the nail. I believe I used 1045 for this header and yes mild for the handle. BUT a header can just be a piece of plate with a hole in it if you like :)
@benjaminzedrine
6 жыл бұрын
Yeah if you need to bang out a handful of a particular size, just square taper punch it to size. I made one out of leaf spring, forged to square, rounded handle, round header, sink a "bump", then punch hole and grind flat top. Spring is good cause it will hold up good and strong without heat treat.
@giorgio1943
3 жыл бұрын
Amazing
@bosshadowrock
Ай бұрын
OK, but how did they do it back in the day before 10mm round stock?
@torbjornahman
Ай бұрын
Well, they made the 10mm round stock! :)
@frenzybait3117
4 жыл бұрын
Hello torbjorn.could I use clips from your video on forging a nail,to advertise a fish bait,as its perfect for what I need.thank you
@torbjornahman
4 жыл бұрын
Send me a message on my web page!
@mikeanderson8601
5 жыл бұрын
Traditionally what thicknesses of nails were produced? This one seems very thick. But could hold larger pieces of wood
@torbjornahman
5 жыл бұрын
I would say whatever was needed! In general the iron used for nails back then does not compare to modern steel in regards to strength so they needed to be a bit thicker.
@iknowwatdadogdoin5454
Жыл бұрын
Tyx I wanted to know how to forge
@TomvdHeuvel
10 жыл бұрын
Hello. Thanks for al the cool blacksmithing video's i myself work with metal everyday but in a whole different way. I was just thinking about that power hammer you have, where i work we have a couple of excentric flywheel presses. We have C clamps on them to punch hole's You're power hammer ( i assume flywheel powered ) looks a lot like the machines we have except your machines goes up and down a lot faster and i assume its very easy to adjust the height and the stroke of the machine. Can you put a C clamp under your power hammer to punch holes with that? Greetings from Holland.
@torbjornahman
10 жыл бұрын
Hondapiloot Thanks! Not sure what you mean with c clamp in this context. A power hammer is quite different in design than an excentric press. It does not have a large mass flywheel, and the power is transfered via a spring of some sort (mechanical hammers). You could make all sorts of tools for punching holes, maybe even for sheet metal.
@TomvdHeuvel
10 жыл бұрын
Torbjörn Åhman Ah i see, so its really a different machine then an excentric press. I dont know if i can just paste this link, i'm sure you've seen one before but i didnt know that a C clamp would be a clamp to clamp stuf together :P Totally different use of the same word. We call it a C clamp cause the main body is shaped like a C In the top we have the "nipple" and in the bottom the "die" The nipple is held u by the springs. www.fdp.nl/cmsfiles/vulcanus/definitieve_afbeeldingen/DV_def_03_05.jpg Greetings and thanks again.
@torbjornahman
10 жыл бұрын
Hondapiloot Ok. I'm not sure a tool like that would work. Many hammers hit so fast you risk hitting the tool twice which could result in double holes. Then there are hammers that hit with such force that you would ruin both the tool and the work I imagine.
@DRKWxd
9 жыл бұрын
That is awesome!
@BClarktv
5 жыл бұрын
Thank you
@hammer326
4 жыл бұрын
Hell of a draft in that forge. I've built the same hood and am having some issues. Is yours fan assisted?
@torbjornahman
4 жыл бұрын
No it's all natural draft. What size flue pipe do you have. I don't recommend anything smaller than 10-12" (mine is 12"). And if the pipe bends anywhere that restricts the flow as well.
@hammer326
4 жыл бұрын
@@torbjornahman On the advice of a fairly ignorant cohort I went with but 6" pipe and there are two 90 degree bends in it so we could go out the wall and not the roof. We're putting a fan in and going from there but glad to know I was at least right in my suspicion the diameter of the pipe is all but definitely a problem if not the biggest one. I Appreciate your time and love your work!
@torbjornahman
4 жыл бұрын
Yes, that's not going to work well. Lets hope the fan solves it. It's easy to think 6" is half the size of 12", but in reality it's just a 1/4...
@johannbarnard5893
9 жыл бұрын
beautiful
@butafly5117
6 жыл бұрын
Did you quench in water at the end? I thought it was supposed to be cooled in air can't remember why though.
@torbjornahman
6 жыл бұрын
This is mild steel, so it's fine to cool them off in water. If it was proper steel you would make them hard and brittle in the water quench.
@Lichupaf
5 жыл бұрын
what kind of carbon do you used? and how long does it last? (sometimes i see you with more of it and sometimes with less) so i was wondering..
@torbjornahman
5 жыл бұрын
The fuel I use? Mostly coke, but here I use coal. It last quite long. With a whole day forging I could probably burn 10kg or so.
@Lichupaf
5 жыл бұрын
Torbjörn Åhman thank you very much for answering, 'carbon' is coal in spanish, sorry about that it slipped through haha.
@crashwelder5337
6 жыл бұрын
btw, i really enjoy your work. do you do custom stuff if i gave you a drawing?
@torbjornahman
6 жыл бұрын
Maybe :) I have very limited time for stuff like that, but if it is interesting enough, who knows.
@scottschmittmusic
Жыл бұрын
Nice!
@genesmith5188
9 жыл бұрын
have you made a video of making that nail header ? nice looking tool
Пікірлер: 339