This fixed my 2005 Ram 2500 Cummins. Odometer and shift position indicator off. No inside turn signals or any alarm lights. They would work for a day or two if it was hot outside. Been that way for about 5 years. 242,000 miles on the Ram.
@colbyleonard7903
Жыл бұрын
Not sure if it’s an issue on the earlys but on my 06 I made some plastic washers/insulators that go in between the board and the shell to reduce vibration because the board doesn’t get completely clamped in the shell. That’s what causes them to come undone. 3 years later still working as it should🤟🏼
@claesevensen4272
Ай бұрын
Super, soldered the 2 middle transistirs, now the gear selector working
@rickharris5485
9 ай бұрын
Mine ended up being the big white resistor for the odometer and all the indicator lights under the tachometer. In my case none of the indicator lights worked in the display. I had to remove the needles and the face plate, which turned out to be a pain to get them put back on in the correct position. It helps to have a bi-directional scanner with a gauge calibration function.
@agdg94
8 ай бұрын
Did you replace the resistor? I tried everything in the video suggested but still no odometer or indicator lights
@rickharris5485
8 ай бұрын
@@agdg94 I watched a few of these videos and there's another video that has you take off the needles and faceplate. Once you do that, it exposes the two pins of that big white resistor and a couple of components right next to the resistor. In the video, it was one of the two components that had come loose. I didn't mess with any of the chips or components that the guy in this video talks about, except the big resistor.
@waynotraffo9221
7 ай бұрын
Mine was also the ceramic resistor solder......they do get very hot when on...
@floridatrailrider305
3 ай бұрын
Can you fix mine?, I was going to try fixing it but my board seemed a bit different. I have 2003 dodge ram 3500 5.9 Cummins.
@randytweten6714
2 ай бұрын
I did what you said and it worked! Thank you.
@neilsteffler2019
Жыл бұрын
My circuit board by the mosfits is burnt is that repairable. And is the 3500 diesel clusters different it’sa 2003 model year. Thanks for any help you can give me.
@ryankisiel4121
3 ай бұрын
My shift indicator and mileage go out only when I turn head lights on. Will it fix that problem or is there something else going on
@DieselCamper
3 ай бұрын
That sounds like a job for circuitboardmedics.com which is where I ended up sending this unit to get fixed. My fix didn't last long unfortunately.
@issaccarrizales1989
Жыл бұрын
Thanks for the video, I've been driving around with the same issue since this is my only vehicle. On mine all of the indicator lights such as (CEL, door ajar, wait to start light) also stopped working. Did you have the same problem? Is it the same fix?
@ClutchTFS
Жыл бұрын
I have the same issue paid 800$ for a new tipm and it didnt fix it so here i am 😅
@issaccarrizales1989
Жыл бұрын
@@ClutchTFS After finding another video I was able to fix my issue. I can give you my email address if you have any questions.
@ClutchTFS
Жыл бұрын
@@issaccarrizales1989 thanks! would you be able to send me a link to the video?
@python929
Жыл бұрын
@@issaccarrizales1989 Hello, could you share what the fix was for this?
@alexkayne4919
Жыл бұрын
or can you share the link?
@bartfart2123
Жыл бұрын
i have a 2003 2500 ram cummins and i have about 600,000 miles on it. the odometer slowly faded and went dark around 550,000 . a couple of times it came back on briefly when it was warm and very low humidity but has been dark for a couple of years now. i removed the cluster the other day ( had to swap out the cluster lights anyway, good time to do both i guess) the two MOSFETs you show in the center of the circuit board are not on mine. nor is there a keyless remote module. i took that thing apart and went over it with stacked magnifying glasses looking for broken solder to no avail. new dash lights are awesome but still no odometer. i'm stumped. i wonder why the difference in circuit board designs? maybe for diesel?
@Vivianauxito
Жыл бұрын
Thanks for sharing your expertise! Is there a way to contact you for doing an LED lighting review?would like our product could be a part of your fantastic content 🙏🏻
@JB-kw4ug
Жыл бұрын
Good info, thanks again for a great tuner, works great! JB San Diego
@nsacco208
Жыл бұрын
Which one is where you solder for the 06 problem of having no or inaccurate tachometer?
@DieselCamper
Жыл бұрын
The tach issue is the horizontal chips on either side of the lower board section as I understand it. The 06 has them in the same place I think.
@jackieemerson984
9 ай бұрын
I know this is an older video but what year truck are you working on?
@DieselCamper
9 ай бұрын
2005👍
@2ACountryCouple
Жыл бұрын
About to start this little project right now. Need to get some flux first though
@rpsmith
Жыл бұрын
Great video! Thanks!
@robcolumbus5330
11 ай бұрын
Do you have a fb page? I hate communicating on KZitem
Пікірлер: 34