Finally a good explenation! Tried to follow few other videos and it was a mess, couldn't undertand almost nothing and had zero success prototyping this circuit on breadboard. I am so happy I've found this video, not I finally managed to make this circuit :)
@lexandro
7 ай бұрын
finally i understood this circuit! Thank you!
@lookupverazhou8599
Жыл бұрын
I hate robots, but that was admittedly a great explanation. And can we thank the heavens for the people that invented transistors. Geniuses.
@kabandajamir9844
10 ай бұрын
The world's best teacher thanks sir
@YuriWhite2251
8 ай бұрын
Круть. Мы такой на городских соревнованиях в 10 классе паяли. Команда из 3 человека. Нужно было спаять, подключить к блоку питания, и для дополнительного контроля к осциллографу. Уложились в 47 секунд.
@manishsaurav7955
Жыл бұрын
Its working... And more simple the others multivibrator circuit
@OMNI_INFINITY
Жыл бұрын
Thanks! Although voltage is isn’t measurable at only one point. It has to be measured between points. So figuring out what was going on in that diagram because of that was somewhat confusing. Also clearly labeling + and - on caps would be better.
@lookupverazhou8599
Жыл бұрын
High voltage is positive.
@OMNI_INFINITY
Жыл бұрын
@@lookupverazhou8599 Heard now he said pos sides of caps are connected to the collector pins of the transistors.
@peatmoss4415
11 ай бұрын
The shaded side of a cap is negative.
@OMNI_INFINITY
11 ай бұрын
@@peatmoss4415 In that diagram the darker portion is the minus half of the caps?
@emredemirel7244
9 ай бұрын
Thank you very much, it is the best explanation I ever had
@csenghcsengh913
Жыл бұрын
nice explanation, but @8.52 you write the resistors value wrong on left side, because R1=R4 not R3
@johnwythe1409
7 ай бұрын
I have to agree. R1=R4 needs to be less than R2=R3. With R1=R3 < R2=R4 both C1 and C2 will be charging/discharging through the same value resistor, hence s/b at the same rate. Question I have is, do both C1 and C2 have the same potential to charge/discharge, and does that make a difference? Why does one Capacitor have to charge/discharge faster than the other? What would happen if the rate was the same? What would happen if C1 rate was slower than C2, instead of higher when indicated here? By not making the R pairs equal in value, can the duty cycle be changed, so one led is on longer than the other. Can the frequency be changed, just by changing the value of the capacitors, just the resistors, or do both have to be changed?
@mostafaesmail3674
Жыл бұрын
Thank you, the explanation is obvious and really helpful
@d.d.s.9347
9 ай бұрын
Sehr schön animiert und auch super erklärt. Daumen hoch !👍🙋😀
@vahagnmelikyan2906
Жыл бұрын
OK I think I'm finally beginning to understand, but in my own imaginary way of vacuum suction of particles and a high pressure buildup. Basically the capacitor being charged, so one side is a vacuum of particles (-) and other side is under highpressure loaded with particles(+) (even though it's the positive that pulls negative, but it's better to think the other way around. So one side of a capacitor you have high pressure build up ,while other side of capacitor (-)is vacuum lack of particles. And eventually capacitor becomes fully charged. Than during that time the other side capacitor begins to charge and when that happens, the first capacitor transistor gate closes and the collector begins to fully conduct electricity. And because the capacitor positive side is connected to collector and it was under high pressure the positive particles flow through the collector (releasing the pressure) and discharges in the negative side of the battery power,while the negative side of the first capacitor that was charged if we remember it became a vacuum (lack of particles), so it cannot suck positive charges from the gate of the other transistor which is connected to negative terminal. Instead the vacuum sucks the positive particles from top resistor that is connected to positive terminal. And it will continue to suck the particles of positive until it becomes completely neutral (or discharged capacitor)... And after it's discharged than ,the direction of the current changes and the capacitor begins to recharge again by turning on the other side transistor l. Something like that.
@ВеселыйСтудент-ъ3й
Жыл бұрын
Именно для этого грамотные люди и двигали технический прогресс. Чтобы любой человек, с любой точки планеты, мог открывать для себя новое, интересное, а самое главное, правильную информацию. Спасибо за хорошее изложение материала.
@bertspeggly4428
10 ай бұрын
Where are the values of the components stated? How does anyone build this without that information? But the description of the operation is good.
@skychip7784
Жыл бұрын
This is very helpful 👍.
@Profmad
Жыл бұрын
Glad it was helpful!
@rodolforibas
7 ай бұрын
this is the “hello world” of electronics?? Goddamn
@paulpomme2502
Ай бұрын
Unless I'm mistaken, the crossing should not be drawn as a node.
@mbart
Жыл бұрын
I have a question at 9:04. Is your formula right? I would expect R1=R4
@csenghcsengh913
Жыл бұрын
you are right, wrong notation
@bsubramani
8 ай бұрын
Very good explanation. I think this type of circuit is also called Flip Flop circuit.
@balbuenaedwin
Жыл бұрын
Changing the capacitance value will change the blink frequency
@Accumulator1
7 ай бұрын
Subscribed. This type of tutorial video I need to understand and learn. Want to try build this too.
@Profmad
7 ай бұрын
Awesome, thank you!
@marh122
8 ай бұрын
is the middle section interconnected ? I mean is current also flowing from Q to T1 ? or those are different cables
@rentoneureka510
10 ай бұрын
Nice explanation
@wilmorekunda9739
6 ай бұрын
If T2 is in off condition the resistance of the transistor is high and almost all voltage Vcc is assumed to be acting across across it by this fact it will be assumed that voltage across R4 will be zero and no current flows through load resistor R4 capacitor C2 will be discharging not charging as there will be no current through it...thats according to my understanding i wish to be corrected if am wrong????
@vladGames228
5 ай бұрын
I don’t get it, if the polarity changes on the capacitors, then why does everyone use electrolytic capacitors for this circuit and everything works?
@ramupattu9444
3 ай бұрын
Non electrolytic capacitor voltage range starting from minimum 230 volt . But our requirement 10 mfd /25 volt. So , select electrolytic capacitor, and its cost 5 rupees only.
@shankar0015
8 ай бұрын
well explained
@mayurkumavat3640
10 ай бұрын
Thanks, very well explained! Cleared all my doubts, just one thing is bothering me is that if both pair of transistor has same components of same specification then both should operate simultaneously, I know due to some operating or environmental conditions little delay can happen, but thinking technically, this is not digesting.😅
@jinsoku1911
8 ай бұрын
You will never find 2 resistors for example that have exactly the same resistance. Most you buy are for example 1%.
@mayurkumavat3640
8 ай бұрын
@@jinsoku1911 okay, understood, thanks 👍
@kabeerfcc4153
Жыл бұрын
I am following your videos respected professor
@Profmad
Жыл бұрын
Glad to hear that
@kabeerfcc4153
Жыл бұрын
@@Profmad sir please make van de graph generator in front of camera , if possible please
@sungurtigin7258
Жыл бұрын
Amazing video and animations are very good thank you for that
@Profmad
Жыл бұрын
Glad you like them!
@alvioalvians2584
Жыл бұрын
Wow thanks you Sir
@Profmad
Жыл бұрын
Most welcome
@degreeless_engineering
8 ай бұрын
I'm an idiot when it comes to electronics, but I really want to learn. Am I understanding correctly by saying the on/off timing of the two separate bulbs is created by the difference in resistance on R1/R3 vs. R2/R4?
@laualbert1740
Ай бұрын
Anyone know 3:27 why do the voltage in P and S decrease?
@zerox4231
Жыл бұрын
I tried doing this on a pcb but both LED turned on at the same time. Can you explain why it isn't blinking?
@peatmoss4415
Жыл бұрын
It works because of the variance in tolerances of the components. If they are so very close in values the oscillation won't start. I did this once by accident. I took my twizzers and lightly shorted the transistor legs to start the oscillation. But that may not be your problem. Just double check the connections. This is a very common circuit.
@zerox4231
Жыл бұрын
@@peatmoss4415 i tried it on a breadboard before and it was working just fine but when i solder it on a pcb either both LED turned on or just one. I did it a couple times and got the same results. Maybe a component wasn't functioning properly?
@pierretessier1682
Жыл бұрын
You write that R1=R3 and R2=R4. I think that's a mistake. I think R1=R4 and R2=R3 and R2 and R3 are much higher than R1 and R4. Is't correct?
@note9redmi17
7 ай бұрын
"R1=R3 R2=R4" Are they wrong? Sould be "R1=R4" and "R2=R3"
@I_don.t_know_6
5 ай бұрын
Yes ! Capacitor I used are 10uF/25v R2=R3 ==> 2.2K ohm R1=R4 ==> 220 ohm Transistor ==> BC547
@I_don.t_know_6
5 ай бұрын
And also the speed can be changed connecting the upper end of R2 And R3 together connecting to a potentiometers middle pin , while one pin of the side of potentiometer is connected to the top power line
@paulpomme2502
Ай бұрын
This trend of putting repetitive tin music in the background is really a shame. Especially when you are explaining something
@yourinsectou6387
9 ай бұрын
how can that polarized capacitor be charged in oppositite direction please help
@dhyana029
2 жыл бұрын
Sir, your animation is very simple. May i know how you do the animation for your videos .Thanks.
@Profmad
2 жыл бұрын
These videos are created using Blender 3.2. Blender is a free and open-source 3D computer graphics software tool set used for creating animated films, visual effects, art, 3D-printed models, motion graphics, interactive 3D applications, virtual reality, and, formerly, video games. You can download it from here : www.blender.org
@dhyana029
2 жыл бұрын
@@Profmad thank you sir for your valuable information.
@lydiachanda2389
Жыл бұрын
What Da ae
@tiwanakmal3428
Жыл бұрын
Sir, how much the value of capasitor and resistor that used?
@Profmad
Жыл бұрын
It depends, as an example you can use followings R1, R4 : 740 Ohm R2, R3 : 470K Ohm C1, C2 : 10 uf By increasing the capacitor value, the vibrating frequency can be lowered.
@c2225
Жыл бұрын
@@Profmad but you said at 8:52 that R1= R3
@anayatali781
Жыл бұрын
@@c2225😂😂😂
@kebabsharif9627
2 жыл бұрын
very nice video. can you make a tutorial on how to make this video Please!!
@Profmad
2 жыл бұрын
It was created using Blender 3.2. Ill create a tutorial for that also. 🙂
@kebabsharif9627
2 жыл бұрын
@@Profmad Thank you very much.
@ilya5782
Жыл бұрын
Thanks for the video. I am very new to electronics, Can i ask a quesiton? if so, why is current not going to T2 from R2 but only going to C1 when C1 is Discharging can't it go both T2 and C1 at 07:03 ?
@ryszardsinius4828
Жыл бұрын
I think that is because T2 is in an off state and its emitter is not conducting, but I'm as green as you :)
@chironjo
9 ай бұрын
T2 is OFF because (at the time that you are making reference ) the voltage at T2 base is less than 0.7V, which is the minimum threshold to turn on T2. Therefore, there is NO current flowing (remember, in order to have current flowing you need to ‘complete’ the circuit). Current does not flow through capacitors. Capacitors charge up to the connected voltage potential, and the electrostatic charges that accumulate in it when voltage is applied, discharge through the connection to the circuit return (there is no ground in this circuit) made when T2 turns ON.
@djagareksa.bahureksa
Жыл бұрын
4km Generator square signal which is 0 to +5volt DC
@saidave9148
2 жыл бұрын
Circuit operation can not be displayed clearly due to subtitles.
@Profmad
Жыл бұрын
Check now.
@anybody007_who
Жыл бұрын
"hello world" program is confusing; it does nothing. So it's not helpful to show, what a program can do. Rather a "two number addition" program can be helpful, i think.
@thomaskallmyr
Жыл бұрын
❤ESCARGENCY ❤😮❤
@sunnyoutside5288
Жыл бұрын
Imagine 3 LEDs in a triangle but instead of leds you make electromagnets turn on and off
Music plus robotic voice does my head in, sorry but what about a bit of down to earth chatter.
@kemalgeleto1258
Жыл бұрын
Plc could you explain how to work SMPS
@Profmad
Жыл бұрын
Hope this video will help you : kzitem.info/news/bejne/p2iaqYdrqoF2a3Y
@charosenz
9 ай бұрын
Great vid, but please stop the annoying and disctracting background music next time. thanks.
@josen.k.8620
Жыл бұрын
You need not increase expenses when your income rises or increases.Jos.
@nabashnani7594
7 ай бұрын
Challenge for those don't now electronic used this circuit to blind 3 led in different time
@lydiachanda2389
Жыл бұрын
What does Edith maen
@zinzotso
9 ай бұрын
Components plss😊
@ngk_Hamzah
4 ай бұрын
5:43 anyone can explained me,why Q side become -0,3V?
@ngk_Hamzah
4 ай бұрын
so the Q side has to keep being 0.3V lower than the right side.what is it mean?
@tommstanley6021
Жыл бұрын
What transistor numbers can be used for this 9V circuit? Thanks.
@nicktm3839
Жыл бұрын
You can use any general purpose npn transistor like c1815 or c945.
@johnlabuci96
2 жыл бұрын
can anyone explain to me, why and what happen in 02:14 .. why voltage gradually decreasing and finally become 0
@Profmad
2 жыл бұрын
when you apply the knee voltage (0.7 V) to the base pin of a transistor, the resistance between the collector and emitter pin becomes 0. That means the voltage of the collector should be equals to the emitter. Normally we consider this happens instantaneously. But actually it takes few microseconds. during this time period the voltage difference between the collector and emitter decrease gradually.
@johnlabuci96
2 жыл бұрын
@@Profmad thanks a lot
@junedmohamedahmed2659
10 ай бұрын
Tranislate to somali
@daminipatil2710
Жыл бұрын
sir can you plz send the transcript of the video plzzzz it will help my project
@peatmoss4415
11 ай бұрын
The transcript is in the video description. Under the "...more"
@omrmmmdzad6849
Жыл бұрын
What is this simulator name?
@Profmad
Жыл бұрын
Blender 3.5
@bandimanideep2991
2 жыл бұрын
Sir ur name plz
@ngk_Hamzah
4 ай бұрын
I don't understand, I've been understanding this circuit for years, and I still don't understand this fucking simple circuit😂
@barenekid9695
8 ай бұрын
OR?? could simply buy Flashing leds . Nawww too easy.
@nitishpandey2151
Ай бұрын
Hindi yaar bol
@many_verse_one_topic
Жыл бұрын
Hindi is our mother language plzzz teach us in hindi
@nabakumarghosh5968
8 ай бұрын
Haaa blkul Shahi 😂🎉❤
@gaboaaa23
Жыл бұрын
Hello, I have a battery holder where 2 mini 1.5v button batteries belong power a LED. Unfortunately, they are always very quickly empty. I now wanted to feed the LED with 3V power supply instead of the 2 1,5V batteries.. If I put the minus cable to one pole of the battery holder and the other plus cable to the other pole, the LED does not light up. Do I have to make a bridge(connect the 2 poles with each other) between the two poles (plus and minus)? I attached a picture of what I mean: drive.google.com/file/d/16HTlUvZGBan05GhirxAmT-myxfN0AEpY/view?usp=sharing
Пікірлер: 107