Your very helpful, how much would you charge for this job
@adamsny6605
2 жыл бұрын
Super.Regards Adam Poland
@paulp4562
Жыл бұрын
thanks - i wanna replace a CAS module only as i have a communication error
@kellsautos9183
Жыл бұрын
After writing the the isn into the cas module, do I need to sync it? If yes how can it be done with im608pro
@thebmwcrown
Жыл бұрын
after all these steps how do you edit the vin to match car in dme and cas
@tiagardner8412
12 күн бұрын
You said a new key needs to be programmed? Would the dash still light up I did this exact procedure now my dash doesn’t light up hazards and some lights is all I can get it to do
@muhammadfaziz1441
2 жыл бұрын
After watching your video I try to Programmering cas3 but when it comes to input dme Ian there is one more window asking ews isn how to read this isn from im608 plz help
@Julicauto
Жыл бұрын
Hello. Normally how much you charge for that? Regards.
@iskooobydoo
8 ай бұрын
Hi can I do this basically but with a CAS4? but i'm not replacing anything. Situation is the Cas module lost coding as someone tried adding a key via obd with an 'Xtool'. I don't know if its just the coding lost or if the eeprom/flash is corrupted. Now on Immo status scan, error is 'CAS no coding stored'. also when I check vehicle frequency, it says 'Unknown Frequency'. I already have the DME ISN..and pretty sure its a 315mhz. However, what if the eeprom/flash is corrupted and not just a lost coding? If its just a coding, how do i recover that if there's no backup. Ask the first guy and he doesn't know if he even backed up anything.
@muhammadfaziz1441
2 жыл бұрын
Can u make same video for cas3
@jesusitoalfonso7472
Жыл бұрын
Do you know on what hex address the isn are stored ?
@danielcrupi2543
2 жыл бұрын
Thank Great learning experience..not hoe did you get dme isn code from which location?
@huyug1
2 жыл бұрын
Thanks! Through obd2
@rogergerdak4709
2 жыл бұрын
Great Video!! One question, I have a problem with my dme. I have another one from donor car. So my question is can I make backup from original DME and put the file to the new one via OBD? using Autel Im608
@huyug1
2 жыл бұрын
That depends on the DME type.
@rogergerdak4709
2 жыл бұрын
@@huyug1 my DME is MSV80
@lerma303
Жыл бұрын
I will not recommend to used obd for that, to be safe use direct connection to ecm on bench is easy and works just fine and is safe
@mattnorton9333
2 жыл бұрын
Good video, thanks. Did you use winfkp to update vin on donor dme?
@huyug1
2 жыл бұрын
We did not update vin on the car. The customer just wanted to have the car running. All I did was renew CAS and marry it to new DME.
@Eurosmithpro
7 ай бұрын
@@huyug1 Did using the 4 digit ISN work for this job?? normally they are looking for 32 digits
@ARMARTUR
2 ай бұрын
@@Eurosmithpro same question. Cas3 I have 32 dig ISN but autel wanted 4 digit
@wiley0714
Жыл бұрын
Very Nice.....Borat
@renzocaceres9099
Ай бұрын
Hello!!!! what about when you want to program a used ECU but i am still able to communicate with the original ECU. how can i program the donor ecu?
@hristohristov5210
2 жыл бұрын
Hi. I have a problem with my dme. I have another one from donor car. So my question is can I make backup from original DME and put the file to the new one via OBD? I'm using THINKDIAG.
@huyug1
2 жыл бұрын
I do not think thinkdiag has those immobilizer functions yet. You will need a tool that does immobilizer functions on bmw.
@David-rm2zd
2 жыл бұрын
What about the VIN. The car will start and run but the VIN of the DME won't match the VIN of the car right?
@huyug1
2 жыл бұрын
Yes unfortunately
@partoems9376
Жыл бұрын
Hi thanks. so in this case should the ORIGINAL AND DONOR DMEs have same part number?
@lerma303
Жыл бұрын
yes always unless you can upgrade by bmw specs
@maxgarza6036
2 жыл бұрын
Hi I would like know know how much you charge reprogram my CAM, engine control module
@huyug1
2 жыл бұрын
You can connect me at my email at huso.technical@gmail.com
@Yochimitsu1
2 жыл бұрын
I have a problem, i replace the cas and the dme module, the car starts with a bunch of lights because the vin in cas dont match the car, i tried to change it vvdi prog, but then when i treid to read it saids vin faulty and if i put back the original vin works, do you think with this solution you think it will work ?
@huyug1
2 жыл бұрын
You need to have have the same isn and vin number in CAS, DME, and EGS. You can renew or clone the CAS and DME from original if you have or reset the egs to sync with new cas.
@Mirro3m
3 жыл бұрын
Hi buddy,, Do I have to connect it on bench to read eeprom ?
@huyug1
3 жыл бұрын
Yes
@angelita1479
Жыл бұрын
My ecu has water damage so I bought an used dme cas and I have keys to that . But problem is this unit has high miles. I need my original cas programed into this dme. Do you do this kind of work?
@huyug1
Жыл бұрын
Yes definitely, if you send me your new cas, and instrument cluster I can align it for you. I would also need your original cas module to extract the original mileage of your vehicle. Another problem is now your vehicle is reading another vin number not your original which also needs to be fixed.
@angelita1479
Жыл бұрын
@@huyug1 I didnt see this until now. How much to fix this issue?
@samuelsingh2015
11 ай бұрын
@@huyug1hello how much to program a new ecu mine is damage
@mcdlol6
3 жыл бұрын
My xp400 will turn off and won’t communicate after trying to read cas2 I have to disconnect xp400 and reconnect and it will comunícate again it will do that over and over but my xp400 is good I’ve made keys or MB for example no issue! Any idea what the problem could be?
@huyug1
3 жыл бұрын
As much as I know xp400 has a issue like that which is a hardware issue. Your supplier should give you another one. Unless you put wrong connections which is very common like connecting obd to xp400
@mcdlol6
3 жыл бұрын
@@huyug1 it was my connection! Thank you sir!!
@alexdonis3789
Жыл бұрын
where are you located
@monsonlockandkey
3 жыл бұрын
Did the ECU renew delete all the keys? I have been looking for this function.
@huyug1
3 жыл бұрын
No all the keys were active.
@monsonlockandkey
3 жыл бұрын
@@huyug1 I have been looking for the function to delete all the keys to start fresh.
@huyug1
3 жыл бұрын
@@monsonlockandkey you can disable the keys and delete keys from coding function I believe but in diagnostic section and coding section. Go to car key memory and look it up.
@huyug1
3 жыл бұрын
@@monsonlockandkey or you might want to look for a virgin file which I don’t have. It will make the cas totally new with no vin or keys stored.
@abbydavis352
3 жыл бұрын
What would happen if you chose flash instead of EEPROM?
@huyug1
3 жыл бұрын
It won’t write the file since the file size is totally different. EEPROM file is much smaller than flash file.
@abbydavis352
3 жыл бұрын
@@huyug1 How did you get the isn from the replacement computer? Thank you for your time.
@huyug1
3 жыл бұрын
@@abbydavis352 I have connected the new dme to vehicle and read it through obd with im608
@joec3045
Жыл бұрын
Hello what tool did you use to read isn of DME?
@huyug1
Жыл бұрын
Through OBD using im608
@joec3045
Жыл бұрын
Ok thanks
@scottiedog100
3 ай бұрын
Water in ecu, replace 2k by bmw specialist, heavy rain and back to square one. Red triangle in a red circle. Immaculate series 1 msport coupe now expensive. paperweight
@jamessmith8480
2 ай бұрын
The beauty of German engineering! 😂😂😂 Sorry my friend, I am in the same boat.
@Mirro3m
3 жыл бұрын
Can I read the eeprom without doing it on bench ?? It wont pass on obd
@huyug1
3 жыл бұрын
Only bench
@therivalryan
2 жыл бұрын
this job can be done via obd with many tools, even cas3, cas3+ not an issue.
@huyug1
2 жыл бұрын
@@therivalryan with Autel im608 it needs to be done on bench. Yes there might be different tools that can do it through obd2 but not Im608. The purpose was to show people how to do it with im608. Not everyone has Autohex2.
@therivalryan
2 жыл бұрын
@@huyug1 Don't be so defensive, I merely said it can be done through OBD with other tools. I was doing these through OBD nearly 10 years ago... AVDI , BMW explorer, VVDI2 ect can all do it through OBD not just Autohex2 as you mentioned, not sure if you knew that. 👍
@reaper110588
Жыл бұрын
Is this what I need to do if I replace cas1 module used on 2006 750li
@huyug1
Жыл бұрын
Yes very similar
@reaper110588
Жыл бұрын
@@huyug1 would you charge to walk me through it? I have Autel im608 customer had already installed used cas1, I tried coding it successfully but still crank no start
@huyug1
Жыл бұрын
@@reaper110588 dynamicautodisgnostic@gmail.com
@Firstmajortomlikestoticker
11 ай бұрын
I have questions
@phannsyyang149
2 жыл бұрын
Hi mr.Manambit how much you cost me sent 2006bmw x5 program use eco/ case module and key .
@huyug1
2 жыл бұрын
Contact me at huseyin0240@gmail.com
@LeeLee-ce6qi
3 жыл бұрын
How did you get the isn from the donor dme? Also you say write the vin from donor vehicle.. did you mean write the vin to Match the vehicle it’s being fitted to?
@huyug1
3 жыл бұрын
I read the ISN through obd2. The original dme did not communicate so o just renewed the cas meaning adapted the cas to new DME.
@LeeLee-ce6qi
3 жыл бұрын
So when fitted to the car what was done about the different vin? Abs system would not match vin so you’d end up with warning lights..?
@huyug1
3 жыл бұрын
@@LeeLee-ce6qi none of the module complained
@huyug1
3 жыл бұрын
@@LeeLee-ce6qi actually that’s a very good question! Somehow none of the bmws I did this way never gave me vin problems, interesting
@LeeLee-ce6qi
3 жыл бұрын
So if I do it the same way you did with the other vin it will all just work? I have im608
@natewithdascat1626
Жыл бұрын
Can you call me ? I have questions bout ecu replacement
@viridian6903
2 жыл бұрын
Cas cant be maked virgin adapted yes
@godssun7840
2 жыл бұрын
Yo
@vlad3k
3 жыл бұрын
thankfully the EEPROM immo data you just saved is all you need to generate a new key to the car ( incase old key cant be programmed anymore )
@huyug1
3 жыл бұрын
If the key data is lost the old key cannot be reprogrammed before being virginized. In that case you would have to do all keys lost and that’s all.
@540animal7
Жыл бұрын
good job awesome Autel. I have one myself! Please return the favor, thx
Пікірлер: 101