Great vid, helped me sort the same issue with my own car. My motor had spun too far also. However I just used a screwdriver and turned it one click clockwise and it lined up perfect again. No need to buy a new motor 👍
@ThatKa5p3r
Жыл бұрын
I have the same issue & almost did this very thing but it has some serious resistance, I feel like if I force a turn it's going to break. Is it a gear inside that actually "clicks" when you turn it??
@MapleJokerRofl
Жыл бұрын
@@ThatKa5p3r same, I did put it back in place without suing the metal guard because it limits your range of motion.. I played with the angles and then once it hooks I push it back into the place it should be. Lot of resistance but the screws will hold it in place. Hopeing it will finds its place again and I can put the metal guard eventually.
@adamhaycroft5610
2 жыл бұрын
Legend, thank you, I have the same fault
@zestemandarine
2 жыл бұрын
Hi I see my clip is also broken however actuator went too far, I mean it tried to open/close valve too much and clip broke. Do I need to buy new clip and actuator ? or I can just adjust this actuator ?
@gregpapagno5683
2 жыл бұрын
I have a f80 m car and I want to stick valve closed. Will this pin work
@motorhead16
Жыл бұрын
Hi. Does anybody know how i can check is the actuator is really working? The flap is always closed (didn't check it while driving' but on my M135i was opening half minute after start-up). I connected it to a 12v car battery, but nothing happened. The car is an Active Tourer 225i. Thanks
@Edzie4849
11 ай бұрын
Hi all i have Dinan exhaust free flow on my X5M 2017, when i put it on sports plus, the right valve is opening but left isnt do you guys know whats the reason for it😑 i went for brake fluid flush at the dealership actually.
@MapleJokerRofl
Жыл бұрын
Mine was off by a few MM .. I wasn't able to put it back in with the metal protector but I was able to get it in at an angle and then force it to the correct position without the metal guard. Screwed it with a lot of pressure from my side pushing it back in place. I'm going to drive it that way for some time. Hope the water and stuff won't damage it. But lets see if it goes back to place so I can place the metal guard back on it. But finally the sound is gone.. it was so annoying. Mine was completely missing.
@kiloton1920
2 жыл бұрын
Same problem on my x1, bringing it in to shop tmrw. No check engine came up either. Will try to fix myself
@MDrives
2 жыл бұрын
No point to take it to bmw. Try to diy
@Dan_k17
9 күн бұрын
I have a f32 440i, had a similar issue, replaced the clip and the rattle stopped for a week, but now the rattle is back worse than before. . I'm wondering if I need a new actuator 😞
@cloogan6781
4 жыл бұрын
When fitting the new spring does the valve in the exhaust need to be in the open or closed position? Or does it not matter?
@MDrives
4 жыл бұрын
Cloogan as you can see on this video when car is stationary the valve stays open and closes when you start a car.
@hnguyencontact
4 жыл бұрын
Hi, how did you aline the new motor cause you didn’t explain how to do it , I’m still blocked with this problem . Thanks for your help
@MDrives
4 жыл бұрын
I forced it with a screwdriver. It was very difficult.
@TNT310supralover
4 жыл бұрын
Thanks
@reeceg93
3 жыл бұрын
My 116i looks nothing like this. I have the same problem but can't find the exhaust pin :'(
@carsandcoldbrew6489
Жыл бұрын
How about for the MPE muffler for the F8x? It uses a different spring
@MDrives
Жыл бұрын
I had mpe on f87 and it was exactly the same.
@jackiewong752
3 жыл бұрын
Hi, thanks for sharing this video. I have the exact same issue. Do you have the name or producr code of the motor? Where can I get it from online shop for a cheaper price?
@MDrives
3 жыл бұрын
Just search on eBay. Used ones cost about £60 in uk
@joehutton83
2 жыл бұрын
So, a question.. I've a m235i. Wanting a bit more classy noise, I brought a brand new mperformance back box.. I've also had the car stage 2 tuned with a cold start delete. I can use bimmerlink to open and close the valve but the car always leaves the valve open.. never closes in eco or comfort just pure noise. I want quiet too! So wheres the issue.. the exhaust backbox swap or the tuning/coding of cold start delete. The valve does work manually with bimmerlink but not with eco/comfort/sport/sport+ who on earth has any ideas... thanks guys!!
@MDrives
2 жыл бұрын
Sounds weird. If the valve closes and opens fully with bimmerlink then I have no idea. Maybe it’s the tune?
@powertec
3 жыл бұрын
Hi mate , did you disconnect battery before removing this valve ? Does it come up with fault ?
@MDrives
3 жыл бұрын
No and no.
@powertec
3 жыл бұрын
@@MDrives thanks for letting me know , im having issue with mine it went to bmw 3x now they have replaced exhaust , they put new valve but i think they’ve never replaced that spring , only thing i can’t understand is why when its faulty it opens and shut while you drive and you can hear it operating 🤔
@zortono8522
10 ай бұрын
How did you move the mother val piece I’m having hard time …trying to align
@MDrives
10 ай бұрын
Forced it with screwdriver
@jdomingo91
Жыл бұрын
I started to read about of the ways to leave the valve open anytime (pulling out the fuse or simply disconnecting the actuator), but I've discovered many opinions. Some say that the exhaust is louder with the valve closed. What is the real truth? in the min 5:32 of the video, when the valve opens, the engine seems to be quieter. If I leave the valve open, then what is the result?
@MDrives
Жыл бұрын
It’s definitely louder with the valve open however it’s not too much.
@chrissantos202
Жыл бұрын
Hey bro my valve authenticators are sqeaking when i come to a stop.. u think if i do a valve delete and leave them open will it help with the squeaks
@MDrives
Жыл бұрын
Hi. If you disconnect it, it should resolve the issue.
@anthonyginn7506
Жыл бұрын
Love your accent!
@MDrives
Жыл бұрын
😅
@anthonyginn7506
Жыл бұрын
Seriously- a proper Yorkshire euro mix. And you’ve helped me diagnose my exhaust issues!
@MDrives
Жыл бұрын
@@anthonyginn7506 I’m a proper Polish Yorkshire man 😂 I’m glad my video helped you. Regards
@eddygjeka5829
2 жыл бұрын
Hey anyone else having this problem I had the actuator actually facing the same way hood was but instead of taking the module out or buying a new one I pressed the pin up against the actuator aswell as securing it into the exhaust flat while I was pressed against the actuator and exhaust flap I started the car and the pin snapped into place so no new actuator or removing anything just plug an play 👍 if anyone has any questions feel free to ask
@eddygjeka5829
2 жыл бұрын
His*
@saadaddy4755
2 жыл бұрын
I was trying to 2 hours to get that clip In. I read ur comments and tried it and the clip went in. Thank you.
@ryanyoder8686
Жыл бұрын
Thank you! I was fighting with this and your method worked!
@pianobyjoey5177
6 ай бұрын
I have the pin in but it’s still rattling, should I replace?
@kiloton1920
2 жыл бұрын
Will this damage the engine if you don’t notice it for a while?
@MDrives
2 жыл бұрын
No. It o my changes the sound.
@johnwayne8
2 жыл бұрын
Hello , whats the part number?
@M_kavi
4 жыл бұрын
How did you unplug the wire harness from the actuator?
@MDrives
4 жыл бұрын
Mattias J you have to press that little plastic bit which locks it in place and then pull.
@Waynos23
8 ай бұрын
Defiantly sounds like problem. New pin ordered.
@MDrives
8 ай бұрын
Good luck
@Waynos23
8 ай бұрын
Huge success lol. I had to use BimmerLink on my phone to open/close the exhaust half way and then pulled the connector to get the pin to fit. All is well at the back end@@MDrives
@MDrives
8 ай бұрын
@@Waynos23excellent news. Glad it worked out
@meady200
2 жыл бұрын
Hey all! Just to add info to this issue. This actuator in the vid was definitely not broken I'm afraid. Mine was the same and it is completely normal. It over-rotates when it has no resistance as a normal part of its function. The problem I had was trying to get it back the groove on it back into a position where it can be aligned with the other side. Switching between driving modes in-car did not help for some reason it almost seemed like the actuator was dead, exactly like in the vid. But I tried using Bootmod3 (diagnostics menu there is a section when you can move the valve open and closed). I got someone to do this while I was under the car, and quickly pulled the cable out mid-rotation. Then it is relatively simple to get the spring in, just a little bit fiddly. Another method is to loosely assemble the actuator and spring with the bolts just finger tight, with the spring out of position but pushing against the actuator. Then get the actuator to switch by changing modes/revving the car or whatever you can find to make it move, and the spring can pop into alignment. You can then do it all up tighter (not too tight the bolts strip really easily be warned).
@MDrives
2 жыл бұрын
Thank you for that. That’s really useful information!
@ijnijman
Жыл бұрын
same issue here: grooves do not align properly to fix the clip and dealer will charge me > €350 to do it :( Actuator is fine as it reposons to sport comfort mode and flips, but I just cannot get it in the right orientation to put the clip in. According to the dealer there is a special mode in which it needs to be set: is this the bootmod3 you mention? How do you get there? And how come there are somany videos where people can just put the clip back in without efforts? My car is a F30 335
@vinbeezy8538
Жыл бұрын
Thank you very very much for this comment. It does take a couple tries to get the pin to stay pressed up against the motor, but I just did this and it worked. Just starting the car and waiting a few moments (warm outside tonight) cause the motor to spin and it thumped itself right into the groove. Excellent idea.
@user-jq7ol9tw5b
Жыл бұрын
I had the dealer look at the same issue and it was the pin - same as everyone, but the dealer is saying that the car needs to be put into "service mode" to replace the pin due to the wires in the actuator; the dealer is now telling me that "service mode" was unsuccessful and the car needs to be reprogrammed (for $450 USD). No one else seems to mention putting the vehicle in service mode in this string. Anyone know what this service mode is and why the dealer needs to engage it to replace a damn pin?
@alexandertako1571
Жыл бұрын
He is just trying to scam you.
@alexandertako1571
Жыл бұрын
Sorry for that
@zllJCllz
3 жыл бұрын
Will this cause my check engine??
@MDrives
3 жыл бұрын
No
@drnick647
4 жыл бұрын
I am in the same position. The clip is completely missing and it looks like the motor and the valve do not line up. I will try to remove the motor and align it with the valve (fingers crossed). There's also a bolt missing that holds it all together :(
@MDrives
4 жыл бұрын
Nothing to lose then. Give it a go.
@drnick647
4 жыл бұрын
FamilyDriver in your opinion, if the groove from the motor doesn’t align with the groove from the valve is that a sign of a bad actuator?
@zestemandarine
2 жыл бұрын
@@drnick647 @FamilyDrive good question
@mohamadchanty7717
2 жыл бұрын
the Exhaust Flap Valve. Originally found on high performance sports cars to avoid upsetting the neighbours in the early hours,
@rl-rc7kb
Жыл бұрын
n55 with default exhaust is not that loud
@drewsXR650L
Жыл бұрын
it wont line up? how to you get it to line up?
@MDrives
Жыл бұрын
If it won’t, your motor is probably already damaged. If there was no pin to stop it, it turned more than it should. You can try to force it back in place but you might break the mechanism inside.
@drewsXR650L
Жыл бұрын
@@MDrives Yep, I actually forced it back and it seemed to do the trick. I was about 20 degrees away from where it should be. Checked the actuator and it moved. So looks like it worked.
@MDrives
Жыл бұрын
@@drewsXR650L great to hear! Does it turn by full 90 degrees now?
@drewsXR650L
Жыл бұрын
@@MDrives The actuator moved all the way in the other direction after installing the pin, so I think the actuator still works fine.
Пікірлер: 76