Dziękuję bardzo mi to pomogło właśnie tego szukałem.
@bartomiejkapczynski3194
Жыл бұрын
Cieszę się bardzo, udanego sezonu! 😉
@marcobenalux7471
3 жыл бұрын
Ciao bellissimo Video stupendo io ho un K1300GTe devo fare la catena di distribuzione, ti ringrazio moltissimo Buon anno sei un grande
@StiloNautica
2 жыл бұрын
Thank you! i have a K1200GT 2006. good day!
@bartomiejkapczynski3194
2 жыл бұрын
Wonderful motorcycle, good luck!
@Flowsalvador
2 жыл бұрын
Thanks you...!!! I have a k1200s/2007
@Cichymoto
Жыл бұрын
Z którego roku pochodził motocykl? Pamiętasz może nr. Łańcucha? Mam problem z doborem łańcucha do siebie. Będę wdzięczny za pomoc. Pozdro
@bartomiejkapczynski3194
2 ай бұрын
Silnik 2009, ja kupiłem części przez bmwstore.pl
@michaelmccarthy3540
3 жыл бұрын
Hello, like your video, can you tell me the bottom slider is it fixed like the top slider, I can move mine about 10mm up and down is this normal. Thank you, Michael Irl 🇨🇮
@bartomiejkapczynski3194
2 жыл бұрын
Not at all, top slider is fasten by pin, bottom slider just put in correct position like on the movie
@kenjiogyvara757
2 жыл бұрын
Great video, but K1200LT engine is totally different. This does not apply on it.
@bartomiejkapczynski3194
2 жыл бұрын
Ups you're right! My bad, sorry. I should try change the title, thanks!
@miguelvite6029
2 жыл бұрын
Does the end of the crankshaft have any mark to know if it is in the correct position before placing the new chain? to verify that the engine is on time?
@bartomiejkapczynski3194
2 жыл бұрын
No, you don't need it. You check only when the piston is on the top position.
@miguelvite6029
2 жыл бұрын
@@bartomiejkapczynski3194 ok, can i see that the piston is at the top from where the spark plug goes? and which of the four pistons should be on top? Thanks
@bartomiejkapczynski3194
2 жыл бұрын
@@miguelvite6029 you kan look thru spark plug socket. 1st cylinder came from right hand side. But it's enough if you follow the movie. You just make sure yourself when you look thru spark plug 😉
@miguelvite6029
2 жыл бұрын
@@bartomiejkapczynski3194 thank You so much!!!
@beaver4529
2 жыл бұрын
Do you know how i can find TDC mark on crankshaft? BMW K1300s. The cylinder head was broken, timing chain replaced :(
@bartomiejkapczynski3194
2 жыл бұрын
TDC is top dead centre, remove spark plug, then you check where is top for each cylinder 👍
@beaver4529
2 жыл бұрын
@@bartomiejkapczynski3194 Thank you, already did it with dial indicator. P.S. For 1, 4 cylinders
@MrDosSantos991
2 жыл бұрын
Can you do it with the engine in the bike?
@user-yy5lo7qo6s
2 жыл бұрын
Yes
@martinamathiasson1115
Жыл бұрын
Video with motor in the bike please
@antonioizzo1149
3 жыл бұрын
A quanti km?
@bartomiejkapczynski3194
3 жыл бұрын
Up to you, I did it when K1200r had about 65000km, I heard the chain noise, and the engine has all the time 1st generation tensioner (the flat one-the bad one).
@tamaskovacs1667
Жыл бұрын
How can you replace the smaller sprocket without the locking tool?
@bartomiejkapczynski3194
Жыл бұрын
It's possible to use wrench on crankshaft, just behind sprocket.
@tamaskovacs1667
Жыл бұрын
@@bartomiejkapczynski3194 Thank you!
@NeroV4Power
Жыл бұрын
Is it possible with out taking the engine out?
@bartomiejkapczynski3194
Жыл бұрын
Sure, no problem. I did it with engine in frame as well.
@NeroV4Power
Жыл бұрын
@@bartomiejkapczynski3194 Yes, i have done this to 🙂👍 Thank you for good video 🙂👍
Пікірлер: 32