Everybody should buy that machine it's great it's good that it removes rust quickly then any other machine.
@simonloveless8924
3 жыл бұрын
Beautiful job indeed well done.
@cmc7095
2 жыл бұрын
Why is this so satisfying to watch
@EnriqueLopez-hb5jn
4 жыл бұрын
That car once it*a painted going to look awesome, 👌🏽👌🏽👌🏽👌🏽👌🏽👍🏼👍🏼👍🏼👍🏼👍🏼👍🏼
@simonloveless1823
4 жыл бұрын
Good machine you are really using there.
@alessandrocolella6766
Жыл бұрын
Complimenti 👍, quanti bar di pressione lavora il getto di acqua?
@nasrirauf704
6 жыл бұрын
Very good
@DumbCarGuy
Жыл бұрын
Rumor has it he is almost done with the bottom of the car.
@magnum357225
4 жыл бұрын
Did u get any warp in the panels from the blasting, and what granulation of sand amd size of tip did u use, because thats cleaning it fast.
@wisfinish
Жыл бұрын
Nice
@wisfinish
Жыл бұрын
The clen up must be hard to do.....little red paint chips everywhere
@caspermaul7583
2 жыл бұрын
Seems very effective, although a bit messy. Did you experience any panel deformation etc. due to the force of the high pressure blast? I've done 3 total restaurations so far and I've gone for a 2400$ chemical dip followed by rust inhibitor application every time. Only way to get the stuff behind the panels etc. that's not otherwise accessible. Protecting these areas after the dip is a bit of a PITY, but it's well worth the effort, in my opinion. Because you are 100% sure that the car is completely free of any rust. If you do it right, the car will last for a very long time...
@geneva760
2 жыл бұрын
Finally, someone doing it CORRECTLY - AKA - with all the glass and trim out. Too many 'marketing' videos up on KZitem showing people wet blasting a car with just some tape over the glass etc - hit any of the glass or trim with that wet blasting and it is RUINED. This video shows the SAFE and CORRECT method. Nice clean BMW shell - would be nice to see the finished project. Being that this video is some 6-years + old - HA - I assume that the operator is a lot more proficient than he is in this video - his technique is poor and wastes a lot of time and effort.
@Armilite1
6 жыл бұрын
Time to Blast and How many 50lb Bags of what Media did you use?
@webbwalle
5 жыл бұрын
nice ledpoisen in the groundwater..
@caspermaul7583
2 жыл бұрын
You should lay down a tarp with a raised lip around the perimeter and collect the used sand and water, and make sure it's "disposed off" correctly. Easy enough without too much extra work.
@yves2348
2 жыл бұрын
What lead ? Smart...
@velvetypotato711
Жыл бұрын
More importantly how did you get your car in the air like that?
@youngsterentertainment
3 жыл бұрын
Do you guys have someone in California? I'm trying to get my cars done
@martinduarte3752
5 жыл бұрын
I need one of these machines...I don't care if my wife. Ruan me off the house.
@toysamsung4793
Жыл бұрын
ราคาเท่าไรจ้ะ
@deettekearns9092
6 жыл бұрын
The process gets great results but that hose is so awkward.
@bigray3360
5 жыл бұрын
Where can you rent one?
@olmdzhmp9902
6 жыл бұрын
how much did you pay for that ?
@nofrackingzone7479
Жыл бұрын
No respirator, or dust mask?
@Jimmy-Legs
Жыл бұрын
He’s an idiot.
@sms9106
6 жыл бұрын
Looks like fun, how fast does it rust after it's done?
@allanmccullough8550
Жыл бұрын
A few minutes.
@oogityboogityshoe1933
Жыл бұрын
It takes a lot of baking soda to strip a car like that, $12,000 worth of baking soda, there must be an easier way and less expensive way to do it.
@1967250s
Жыл бұрын
This system uses a sand type grit, not soda. Probably one of the finer grits. Cost of the grit is $10 or $20 a bag. Most of the cost is labor which includes the pressure machine.
@gnoy404
Жыл бұрын
А я не понял, где ржавчина
@liamstandish878
7 жыл бұрын
sand is messy
@terryjackson4538
7 жыл бұрын
so is every other paint removal process.
@BobSmith-mc7uq
7 жыл бұрын
Liemm...It is crushed glass....not sand!
@liamstandish878
7 жыл бұрын
Bob Smith its liam... yes i know .. u are 2mts 2 late
@BobSmith-mc7uq
7 жыл бұрын
Lemmy. what the hell is 2mts 2 late? Can you not sound out words, then type them? Have your sister help you when she gets off your lap.
@liamstandish878
7 жыл бұрын
lol
@robertostman2075
5 жыл бұрын
that seems like a poor use of the system, it is not a power washer, it is a sand blaster, the user on the video was taking to long to move from one point to the other, thus hitting the metal, thinning it... weakening it...
@darrellgrant7615
5 жыл бұрын
Robert Ostman you have no idea what your talking about. It doesn’t weaken anything and it’s not a sand blaster.
@caspermaul7583
2 жыл бұрын
It literally IS a sand blaster. The water just helps with dust issues and keeps the metal cool, limiting deformations and warping of the body panels. But this is an abrasive process, and will remove metal. So proper technique is important...
@Johnsormani
Жыл бұрын
@@caspermaul7583 It might cool it but much of the deformation will take place anyway because of the impact , not so much from heat. Especially when I see how this is being done.
Пікірлер: 44