I've pulled 3 or 4 of these out of 753, 763, 773, and an S150. Engines can be pulled without removing any of the hydraulic pumps or housing that mates the engine to the pumps. Remove the flywheel and pull the bolts behind it. The shop manual will tell you to do it the way this guy is, but its a way worse ass ache. No draining hydraulic oil, disconnecting linkages, just pull the affected part, the engine.
@jamescorbin3666
Жыл бұрын
This is a great video. Thanks so much. It will really help me when I pull my 773 F engine. I been wonder how difficult, doesn’t seem to bad.
@drev5001
Жыл бұрын
The 773 will be very similar if not identical. Just go slow when pulling the engine to ensure you don't pull or break wires
@jamescorbin3666
Жыл бұрын
Thanks. I will. I hope you have a video when you go back in with it.
@drev5001
Жыл бұрын
@@jamescorbin3666 it's been on the back burner for a few months now. Life is a bit busy. Hope to resume late Nov early Dec when my new shop is built
@Alexr2735
Жыл бұрын
Thanks for the video, great info.
@tylerbrinker6582
10 ай бұрын
Is there any special procedure to bleed air out of the drive pump?
@PartyRider14
Жыл бұрын
Never got it filmed
@alihamdouchi
2 жыл бұрын
A question please what kind a belt in the far back left below the coolant hose with a tensioner Thanks
@johnwiebe5782
2 ай бұрын
Question, did you end up locating the engine serial number on this 763? I’m just curious where to locate I need to replace or rebuild my engine.
@drev5001
2 ай бұрын
@johnwiebe5782 Hi! I did not show it but the serial number can be found by the injection pump. It is stamped on the mounting surface. When you're looking at the injection pump, it's right in front of the injection pump . Might be oil/grease covering it up. The V2203 engines typically come in only two configurations IDI (indirect injection) and DI (direct injection). Easy to tell by the injectors but I'm 99% sure 763s only came with IDI.
@bobcat8439
2 жыл бұрын
The guy that does how I did it puts a hydraulic hose on the auxiliary hydraulics coupler runs the machine to empty the hydraulic fluid
@hillmonbrooksjr9847
Жыл бұрын
How many bolts are in the valve cover I gotta take mines out
@drev5001
Жыл бұрын
The valve cover is only 3 castle nuts. No bolts.
@itzrisky2422
Жыл бұрын
Aye man i was told by a guy to leave the pump in the bobcat? What are your thoughts?
@drev5001
Жыл бұрын
Sorry late response. I missed this. On these machines they have to come out in one piece. Engine and pumps are bottled to a common plate that in my opinion would be more trouble to deal with in the machine. Atleast that is how I've always done it. The early 90s models where the engine is installed facing front to make on the machine, those can be taken out engine only.😮
@itzrisky2422
Жыл бұрын
@@drev5001 i actually just got done installing the motor. Yeah i believe it can be done but my opinion the struggle to get at those bolts would be a nightmare. Thanks for your response
@drev5001
Жыл бұрын
@@itzrisky2422 awesome sir. Hope everything went well for you!
@rdieyzasoon518
2 жыл бұрын
Do u have part2?
@drev5001
2 жыл бұрын
Sorry. I do not right now. I've been so busy with life outside of this. What are looking for?
@bobcat8439
2 жыл бұрын
My primer bulb broke they are junk
@emmanueldiaz835
10 ай бұрын
Good morning Even I have the same motor in my 763C series . In order for me to get more gpm do I change the hydraulic motor or the engine itself.
@drev5001
10 ай бұрын
Do you need more hydraulic GPM? That would be done by your hydraulic pump. I'm not sure if Bobcat made a high flow model of the C series 763, but they did make one for the F and G series machines. There is potential for the hydraulic pump from one of those machines that could fit on yours, but I'm not positive. You would also have to add a lot of lines to allow for the higher flow as well as valve body changes. Long story short, there would be a lot of time/money involved to make the machine flow more fluid. It would make better sense to buy a machine with higher flow.
@emmanueldiaz835
10 ай бұрын
Ok, I definitely appreciate the input, because I was racking my brain. Than I came across your videos and it shows. That you know what you are doing and talking about.. what would you recommend for a mulching attachment that requires 35-45 gpm.
@emmanueldiaz835
10 ай бұрын
I bought an attachment not knowing anything but know that the mulcher can take down a 5-8" tree but needs a high flow skid steer to to so. Angry years of experience would it be easier to get rid of the the bobcat I get a schedule with or get rid of the mulcher
@emmanueldiaz835
10 ай бұрын
But if I did want to go higher with the gallons per minute I would need a bigger hydraulic pump plus the hydraulic release line for the radiator that cools the mulcher down .( The third hydraulic line) that drains back to the tank/ resivor
@drev5001
10 ай бұрын
@emmanueldiaz835 you would need a lot more than that and again, price/labor out weights the reward. What brand of mulcher head? A mulcher head with the flow rates you described are usually VERY heavy and are ran by machines with double the horsepower the 763 has. You machine might lift the implement but the machine would be extremely stressed and you're risking damage. At the end if the day, I suggest selling the machine and getting a machine better suited for that attachment.
Пікірлер: 27