Great how to! This was not so much news for me but i enjoy watching! You got yourself a new subscriber!
@glennsloggett1876
Жыл бұрын
I have built 8 Revell 5 window kits over the last 2 years and have done a lot of the same things you have done here as well. I also chop the tops too.When I have done the seats I do the same as you in regards to the bottom of the seat but when I do the top of the seat you will notice there is a line near the top that lines up with the side panels. I cut following that line to remove the top edge, then take the same amount as you took off the bottom of the seat off the lower part of the cutoff piece then glue the top back on. You will have to trim the edge a little to sit on side panels. Love the solution for dropping the rear. I will be building my 9th kit soon and will be using your technique for the rear end. 👍🇨🇦
@ScaleModelKustoms
2 жыл бұрын
Hey man, thanks for the videos on the 32, found them very helpful on my current build, super appreciate your sharing!
@johnsavage7842
Жыл бұрын
I just found your videos , this was a very informative series , thank you so much for doing the videos, I hope you are able to do more, again thank you
@jasonmorris4795
Жыл бұрын
Thanks mate, i have been on a bit of a brake from doing videos but will be back doing some soon.
@eme5793
Жыл бұрын
Thank that was great info, as I'm just about to start on a model A and a 32 kit. I'm in NZ so not to far away.
@morrieskustoms6430
Жыл бұрын
sweet, have fun mate, i like building hot rods
@squirrel8037
2 жыл бұрын
I cut the radiator at the top, saving the upper and lower radiator hose locations. Remove the upper tank/reservoir section, then remove the required material(in this build, it would be 6mm) from the upper portion of the radiator itself. Then glue the upper tank back on the radiator.
@michaelcooke2559
3 жыл бұрын
Great detail towards showing us what to do to modify this kit.
@morrieskustoms6430
2 жыл бұрын
Glad you liked it
@bobpratt8224
2 жыл бұрын
Looking good! Like the stance
@morrieskustoms6430
2 жыл бұрын
Right on
@boskinay
3 жыл бұрын
I love building this kit. Built 4 of them so far and still have 2 more in my stash.
@morrieskustoms6430
2 жыл бұрын
I always grab them when they pop up cheap in the model buy and sell groups.
@t.j.lemaster8653
2 жыл бұрын
Awesome build my friend ! 👍🏆 Do you have a Facebook page ? I would love to show you one that I did a chop and body drop on plus a couple others I think you'll enjoy it just sucks that KZitem doesn't allow viewers to share photos with the content maker.
@michaelhintzmikesminiature1812
3 жыл бұрын
Nice continuation. Great video!!!!
@morrieskustoms6430
2 жыл бұрын
Glad you enjoyed it
@75keg75
3 жыл бұрын
Liked an commented for that little bit extra engagement.
@morrieskustoms6430
3 жыл бұрын
Thanks for that!
@THROTTLEPOWER
3 жыл бұрын
👍👍👍
@nealbeggs5962
2 жыл бұрын
Watch your series and enjoy the lot think I will give it ago 🤘on
@davidjohnmiller4849
2 жыл бұрын
That’s called Channeling .... not body drop . Think old school Chop, Channel & Section
Пікірлер: 23