Chris, your video and others that described this issue gave me the confidence to try the "permanent fix" of removing the controller circuit board and using a $4 electric solder gun and $3.50 solder to re-solder the culprit connection. The dishwasher now works great and saved me a fortune in having someone else repair it or, worse, buying a replacement! Thanks for posting this.
@KubotaBXathome
5 жыл бұрын
Wow that’s fantastic to hear, glad I could have helped guide a bit. Congratulations on your great job!
@gracegracelaw
3 жыл бұрын
What exactly did you do? Disconnect and re-solder? TIA
@jnwbman
3 жыл бұрын
@@gracegracelaw Yes. I went to Harbor Freight and bought an electric solder gun and solder. I followed Chris' instructions for the burned out connector. It was pretty obvious which connector was bad because it looked black around the small nub. I just put a very small amount on the spot and, after it cooled, reinserted the board and it thankfully worked.
@philinnc
5 жыл бұрын
Thanks for this. You have restored my faith in humanity. Or at least my sanity.
@KubotaBXathome
5 жыл бұрын
Great Phil, hoped it helped you in some way.
@cityofabscissae
6 жыл бұрын
Hi Chris, It's McConaughey from Nimbus. I have a Bosch dishwasher as well. I'll keep you in mind if mine gives me any trouble. Thanks for the offer. I enjoy all your videos.
@KubotaBXathome
6 жыл бұрын
Cool thanks keep in touch!
@JerryAliotta
4 күн бұрын
Chris, where did you post your instructions? I have the exact model pictured behind you in the video. Purchased in '99 as well. And it's getting stuck on 1 second.
@toddthomas4677
4 жыл бұрын
Great insights continued to look for another how to video from what you talked about and made the fix. Thanks for talking through the solution. Though what is the best way to get the solder to stick right away. How do you clean it up.
@KubotaBXathome
4 жыл бұрын
Hi Todd, expanding the joint by scraping away the green insulation and carbon buildup on the relay terminal ideally after sucking away the solder with a solder sucker or solder wick, then using a knife or razor to clean any carbon buildup, then acetone or alcohol to clean it. Then use apply fresh solder all over the expanded joint.
@jkline999
5 жыл бұрын
thanks for posting! going to rip into my old Bosch now.
@KubotaBXathome
5 жыл бұрын
Fantastic good luck and keep me posted!
@jkline999
5 жыл бұрын
@@KubotaBXathome Fixed. That repair, I thought, was going to cost me hundreds. Thanks and best wishes.
@KubotaBXathome
5 жыл бұрын
Fantastic congratulations and great job happy for you!
@conaniator
3 жыл бұрын
I'm having that problem right now. From the looks of the dishwasher, I have the same unit. Bought it in the early 2000's and this is the first time I've had a problem. Any help would be great, I can send the part to you if that's the best way to go. Thank you for the video!!
@KubotaBXathome
3 жыл бұрын
That would be one option. Can you take a closeup picture of the solder side of the main PCB?
@conaniator
3 жыл бұрын
@@KubotaBXathome I'll take the part out and do that. Moving back into the house after being away for months. Will take it apart this afternoon. Thank you
@burlingtondigs
4 жыл бұрын
Hi Chris, we experienced this problem about two yrs ago with our Bosch DW. I followed your instruction and found the same problem. I did the fix and we had hot water once again and a DW that would shut off. Now it gets to a 01 and runs forever, it would appear that the water is being heated and we have to now drain and I put it on a 08 minute rinse, it runs this and shuts off no problem. I was curious if given this information you might have an opinion on what I could look at for a possible fix. Seems a shame to junk this machine . . . something else I have noticed is that the DW does not appear to be cleaning itself and so I find myself removing the tray and using a spray to clean the inside, I don't think that this is normal either. Perhaps the temp is working but is not getting high enough? . . . our model is a SHU-43c05uc/22. Thanks by the way for the first tip it was great!
@KubotaBXathome
4 жыл бұрын
Hi Michael, that temp idea you have is certainly a possibility. Do you have a thermal temp gun to test the water temp close to the target time? The target temps are listed in the manual for the different cycles. Might be a good place to start.
@burlingtondigs
4 жыл бұрын
@@KubotaBXathome Thanks for the prompt reply. I will look to find these temps you mention, I don't have a temp gun but perhaps my meat thermometer will suffice to give us an idea. Thank you!
@garyabc
6 жыл бұрын
Hi Chris, Today I installed my new Bosch D/W. This is an open box 1/2 price "bargain" from a big box store. Looks like new but I can tell that it had been previously installed. Missing the kick plate and silverware holder. Finished the installation about 5:30 PM. Put in a couple of practically clean dishes and started the auto cycle. No leaks. Seems to work. Hurray. It is now 11:20 PM. The dishwasher is still running. The display says 1 minute to go. There is water in the tub and the wash cycle is still going.Tub doesn't try to drain. Does this sound like the same problem after all these years? I see another web posting that describes soldering the heating coil relay. I'm tempted to disassemble the door and take a look, but it has a full warranty. I will put in a service call and try to look over their shoulder and let you know. Thanks for posting this video!
@KubotaBXathome
6 жыл бұрын
Hi Gary, it does seem unlikely after all these years it would be the same problem, but your description does sound identical to the behavior of a unit that is not achieving target washing temperature. The heater relay solder connection on the PC is the problem I discussed. In fact any fault preventing the heater from functioning would cause this symptom (including a bad heater element). As you already decided since the unit is in warranty just have them repair it. I would be very interested to know if it was the same problem as I discussed. I am sure they will be swapping out the control board and would likely want the old one back for a warranty claim with Bosch, but if you can take a peek at it on the PC side at the solder connections opposite from one of the relays (heater) you just might find a slight burn spot at the bad solder connection.
@garyabc
6 жыл бұрын
Hi Chris, Had 2 service calls from BestBuy under factory warranty. Good technicians. Was a different root cause for me. They replaced the latch assembly on both the frame and the door. There are 2 door status sensors in the latch assembly. One is a microswitch, the other is a magnetic sensor (permanent magnet on the frame side, hall effect sensor on the door). Apparently the faulty door latch was allowing one or both of the sensors to intermittenly change state. First wash just finished, seems to be working fine.
@KubotaBXathome
6 жыл бұрын
Hi Gary, thanks for the information and glad you got some great service there. It doesn’t surprise me that you had different issues since mine is such a much older generation and don’t know when the other generations started. Thanks for posting!
@carlasousa8167
4 жыл бұрын
Hi Chris. I've definitely been having this problem for a while now. Once in a while it finishes the entire cycle and dries but most of the time it's stuck at one. When I open the door, the water is soapy and cool. So frustrating!
@KubotaBXathome
4 жыл бұрын
Yes that would be a failed heater problem Carla. It could be my repair ir a failed heater.
@carlasousa8167
4 жыл бұрын
Kubota BX at home do you still repair these? I was hoping to try to save it before I resorted to buying a new one.
@KubotaBXathome
4 жыл бұрын
I certainly can Carla, but the main PCB would have to be sent to me and before that it would be best to try to confirm the failure mentioned by getting a picture of the bottom of the PCB. How old is the dishwasher?
@carlasousa8167
4 жыл бұрын
Kubota BX at home We bought this in 2007 I believe when we moved into this house
@KubotaBXathome
4 жыл бұрын
I don’t know if by then the design of g type board was changed or not. It is possible you only have a heater element that went out too. I think it less likely but either way it must be confirmed.
@nadinetheoret117
4 жыл бұрын
Could you send us pictures of what needs to be soldered exactly? We have the exact same problem (ours is stuck on 13 minutes).
@KubotaBXathome
4 жыл бұрын
Hi, I had some shots on Fixya years ago, will try to find, otherwise if I saw a pic of a PC with this issue I could show what needs to be soldered. It’s a solder joint on one of the heater relay pins.
@nadinetheoret117
4 жыл бұрын
That would great, thanks Chris!
@nadinetheoret117
4 жыл бұрын
No need to dig up those pictures. We ended buying a new dishwasher after all.
@KubotaBXathome
4 жыл бұрын
Oh sorry Nadine, what did you guys get?
@nadinetheoret117
4 жыл бұрын
No problem at all! We got an LG. It works great and it’s very quiet.
@BraddahHuna
4 жыл бұрын
Sir, Mahalo........ Kris
@terrylambert8066
4 жыл бұрын
Mine is doing the same thing where is the board located at, is it in the door
@KubotaBXathome
4 жыл бұрын
It’s behind the control panel accessed from the rear.
@billb6473
3 жыл бұрын
Kabota, I've been trying to ID my Bosch DW but the sicker is gone. It's the same model you have in your video. Can you tell me what model # it is?
@KubotaBXathome
3 жыл бұрын
Sure Bill- SHU5305UC/U12
@billb6473
3 жыл бұрын
@@KubotaBXathome Thank You!
@belindaturberville1026
4 жыл бұрын
Hey I have a bosch dishwasher doing the same thing it gets to 1 minute and continues washing. Can I still send to you and you fix it and send it back? Do you still do that and how much?
@KubotaBXathome
4 жыл бұрын
Hi Belinda, I certainly can what approximate year dishwasher do you have?
@belindaturberville1026
3 жыл бұрын
I just saw your reply. I just had a guy that wanted it today and I told him I would send him the video but I can't find it. Can you send me the link.
@billsmith5146
5 жыл бұрын
Such d/w wont shutoff, the pump keeps running, i have disconnected the power but it stay the same after resetting the breaker.
@KubotaBXathome
5 жыл бұрын
What does the remaining time display Bill?
@SunilVemuri
4 жыл бұрын
In the video, you mention that you posted instructions on fixya. I looked around and couldn't find them. Can you point to where you posted your instructions? Also, I saw this other video which sounded similar the steps you describe. Does the video show the steps you used? kzitem.info/news/bejne/uqCl06KQrmuoeJw Thanks!
@KubotaBXathome
3 жыл бұрын
Yes this is the correct one good find.
@tksmem
4 жыл бұрын
Your thoughts if this could be the problem on a 20 year old unit that has been working fine until lately getting stuck on 01
@KubotaBXathome
4 жыл бұрын
This is possible, is the water getting hot or not?
@tksmem
4 жыл бұрын
@@KubotaBXathome Yes along with steam. Also after opening door then turning back on timer goes to 13 runs down to 01 and keeps running.
@KubotaBXathome
4 жыл бұрын
tksmem unfortunately this repair only applies to the heater circuit being disabled causing a perpetual wait for hot water.
@tksmem
4 жыл бұрын
@@KubotaBXathome Confirmed last night it's only getting warm 80º
@KubotaBXathome
4 жыл бұрын
It sounds like this could be the problem then. Only getting up to hot water heater feed temps and no electric heat to achieve target temp.
@rickpicarazzi3763
4 жыл бұрын
my circuit board shows no burn marks but it does not shut off. Water is hot
@KubotaBXathome
4 жыл бұрын
Rick, if water is hot then this is not your problem. Only if the water is cold would this be the fix. A new board may solve your problem but I’m not sure.
@khalidalshibli4024
4 жыл бұрын
Can you help me to repair the board if I send it to you? How much you charge? Thanks
@KubotaBXathome
4 жыл бұрын
Hello Khalid, yes I can fix for you, the cost is $20 plus postage. Does yours do exactly as described? What is the manufactured year? Thanks, Chris
@Sspmichael
4 жыл бұрын
Hi My bosch dish washer won't stop working, please you know what i can do to fix it?
@KubotaBXathome
4 жыл бұрын
If it’s a failed solder connection this would be what my video is about.
Пікірлер: 71