I just used this method to wire some z bars. It worked fantastic! In the past I have always used a string with a small nut tied on the end but after trying this chain method on my last wiring job I could now see how much better this was.
@georgearmstrong5640
4 жыл бұрын
I am trying to pull wires through an exercise bike handlebar and glad I found this video. It explained what I need to do. Thanks.
@Richardsumilang
2 жыл бұрын
This video deserves thousands of more likes!
@jokerszombieland6019
6 жыл бұрын
What kind of chain is he using ?
@aaronmeyers451
6 жыл бұрын
That’s the easiest part to do. I thought you were going to actually show us how quickly you could bring the wires through, because that’s where the problem is. I don’t see you use in a chain to get both your harness for your switches and your throttle fly by wire.
@JimmyMakingitwork
5 жыл бұрын
Aaron meyers You have to remove the two small connectors that are about 10” from the throttle grip. I soldered 2” wire in place of the 6 pin and two pin connectors there. The large connector at the harness end must be disassembled, then it all pulls thru fairly easy.
@johnalbright8093
7 ай бұрын
Using a Electric Guitar string works, just feed it thru also the good old string and a air compressor works also just feed the string in, then blow air thru the bar with the compressor the string will pop outta the bottom hole like magic. I've used all three methods many times at the shop. Good video, short sweet and too the point
@3360274
10 жыл бұрын
Hey that's one of the best tips for doing this job I've ever heard of! Thanks!
@frankvacanti5277
3 жыл бұрын
Use a dipstick. The checkered end has two holes. And the top end has a variety of Loops or t handles. Transmission dipsticks work even better. Dpnt use w d . 40. Sil glide works best. Napa has it
@adminadmin9997
2 жыл бұрын
You think the Dip stick method will work on 14" z bars?
@boss9311
2 жыл бұрын
we all got that . need video of act. pulling wires thru.
@mikeymike3449
2 жыл бұрын
Until you run a throttle wire, controls wire, and a blinker wire. That corner is hell on all handle bars
@gtownsurfcody
5 жыл бұрын
Pretty good service also man
@flatbedtrucker
4 жыл бұрын
Nice tip Bill🤙
@USMC-es4yy
Жыл бұрын
Yeah some people just dont have common know how like others..ive wired 3 sets of ape hangers and used a similar chain like yours with a necklace clasp on end..takes no more than 45 minutes to get all wiring through..and thats with a 5 yr. Old next to me asking 100000000000000 questions!
@andrewward4486
5 жыл бұрын
In trying that now withthe same type of bars and wheni going around the sharp corner i give it a tug and the tape just keeps letting go so how to u fix the wire to the chain? Thanks
@AnthonyM1
10 жыл бұрын
Thank you very much....very cool and top notch.
@stevenline63
8 жыл бұрын
Excellent video...
@littleand9250
Жыл бұрын
life saver
@tylerguthrie5297
8 жыл бұрын
What bars are those exactly???
@rambobronco
3 жыл бұрын
Yeah customer take that!
@jjkirnag
6 жыл бұрын
Life saver!
@robertpiper8130
4 жыл бұрын
Getting the wires through is another story. The white cluster is 4 times thicker then that chain
@USMC-es4yy
Жыл бұрын
Use a dry lube on the thicker ones..makes a world of difference!
Пікірлер: 29