I learned a simple technic as a you man. #9 wire one loop around posts with a tightening stick of locust. Just twist the loop and rest the stick against by rail. Quick and cheap. We had tractor mounted post driver in the late 60s
@speedydry
3 жыл бұрын
I use lag screws, not staples on brace wire. Will not work loose. I like to use three posts with 2 horizontal braces for all long fences, like the video.
@ronalines
11 жыл бұрын
I place my top brace pin a little differently. I almost drive it in flush but I leave it out 1/2" and it makes a nice place to land the brace wire as I wrap it around twice. The brace wire is placed on top of the pin and is pulled down as tension is applied. Stronger than a staple and holds stout.
@rdlamascus
10 жыл бұрын
Very good video. Zooming in on the handling of wire crimping and threading of high tinsel wire into the tensioners would have been more helpful. Also, zoom on the pin instillation for cross brace posts into the vertical posts would have been nice. Thanks, Rick - Tennessee
@RedBrandAgFence
11 жыл бұрын
Wrapping the brace wire twice adds strength. The most important part of your fence are the braces.
@c.w.hughey2728
2 жыл бұрын
YES VERY IMPORTANT GOOD BRACING STRONG FRNCE
@hillybeaner9689
11 жыл бұрын
I do have one suggestion. Not trying to be an expert but the double h brace would be stronger and take the weight of say a cow or calf running into the fence better if it was braced with the wire contradicting on the posts from bottom center to both top sides on the outside posts. The pull from an animal hitting the fence on the side of the brace that the most pull is already on can loosen after a while or maybe even break posts off if they are pulled too tightly in one direction.
@c.w.hughey2728
2 жыл бұрын
YES YES
@lydite-fence
Жыл бұрын
Wow, thats a great video, thank you. If need any electric fence products, you can choose lydite
@knightsedge7379
5 жыл бұрын
This is very professional. Most tension wire I've seen is a strand of barb wire with a short stick that you twist until tight.
@c.w.hughey2728
2 жыл бұрын
YOU CAN BARB WIRE INSTEAD OF SMOOTH WIRE ALSO FOR AN AGRSSIVE FENCE ONE BARB WIRE UNDER THE WIVEN WIRE AND 2 OR 3 ON TOP
@hillybeaner9689
11 жыл бұрын
It doesn't add strength at the ends of the wire it adds strength as a whole to lessen stretching. I'm not a physics expert I just know what works in the field from experience.
@derekmichael5710
9 жыл бұрын
great explanation of the process! Thanks for the help
@nobueno8652
Жыл бұрын
My mistake was using 12.5 gauge sleeve on a 12 gauge brace wire which didn’t crimp the wire well together and slipped and detached when I tighten on my strainer. My local tractor co didn’t have any 14 gauge sleeves.
@jimrodgers7042
10 жыл бұрын
Great explanation and simple to follow. Thanks
@MoeLarrycurly1
28 күн бұрын
Now that's a nice fence.. I put up fences before . Just around my house lol.. I just never have beena .. good post hole digger..😮
@gabriellabuba
15 жыл бұрын
Dude this is very helpfull and a well done video
@cos1463
14 жыл бұрын
Thanks a lot, very helpful. Good videos.
@skd5432
4 жыл бұрын
At some important tasks like pin insertion etc.... closeup shots could have helped....better.
@davidjustice4029
7 жыл бұрын
it would have helped if the camera was a little closer to the work.
@Cotronixco
3 жыл бұрын
It was perfect. I hate zoomed recordings. Zoom in yourself or get a bigger monitor.
@CnHoltzman1
6 жыл бұрын
so you didn't comment on whether to set the pin a little higher on the corner most post so as to avoid hitting the other pin? Looks like you didn't double the wire as you did in the first video. did you mention the different in pin lengths, five inches and ten inches?
@jamesallen1907
6 жыл бұрын
We don't crimp it we just wrap it and it works out just as good
@markthompsoncpa
4 жыл бұрын
That's one nice pole barn!
@timlebsack
7 жыл бұрын
What are the advantages of using smooth brace pins vs. lag screws ??
@jasonkirk3166
Жыл бұрын
I can't find the brace pins. Where can I find them?
@mcgregorco
8 жыл бұрын
Thanks for the help !
@Cotronixco
11 жыл бұрын
Are you talking about the twisting that posts get after awhile on most fences, which keeps loosening the fence? I always terminate on the inner post of the H instead of the outer for two reasons: 1) to keep the wire centered so no post twisting occurs over time, and 2) to distribute the pull evenly between the two posts, instead of having almost all the pull on the end post. It is simple to then fill in between the posts. You can even lag some 2x's across as a climber.
@chrismalchoff7552
3 жыл бұрын
Correct. Don't stretch from the corner Ever. In the Northeast, staple every 6th post tight. The rest are loose
@mrpush2532
3 жыл бұрын
Couple questions. 1. Why would you measure down from top of posts andThe. up from the ground which is where the ht of fence is determined? I could see this is OK if you got every post to the same ht...but we know in real life this never happens. 2. In that corner post, if the holes are not offset by some distance the pin holes and pins would hit each other. I didn't hear any mention of that? Are they offset by some distance? Thx.
@mywifesboyfriendisfire
3 жыл бұрын
1. Watch the previous videos and you'll see how they set the posts at the same height. 2. Use your head. Either drill your second hole at an angle to miss the first or just move it down 1/2 in or so, in which case you drill your hole in the end of your horizontal a little lower to compensate and no one is the wiser.
@PlayhardStudios1
11 жыл бұрын
thanks guys great video helped me heaps
@Coffeeandasmoke
12 жыл бұрын
Good vid. Thank you.
@ShadowSwayze
3 жыл бұрын
anyone watching in 2021
@eledaedumers7961
9 жыл бұрын
great vid
@NickButters61
Жыл бұрын
what is the recommended length of a fence to require a double h brace?
@jamesdawsoningalls
Жыл бұрын
Every how many feet is a brace needed?
@danielrussell2713
7 жыл бұрын
At a gate in the middle of a straight run, how do you run the wire? I would set posts on either side of the gate, then one more on either side to brace with. Maybe this will help get my point across: ___ ___ ----------------------- | | GATE | | ------------------- A). \ / B). / \ C). X X Which way should wire run? A, B, or C?
@booifojoe
7 жыл бұрын
On all multiple choice tests, I always go with, "All of the above." My answer is "D".
@andrewbohnert3755
6 жыл бұрын
B. Because the weight of the gate will pull the top of the post inward, so there needs to be a wire holding the top of the post back.
@MrFrozensmoke
5 жыл бұрын
Is this for the middle of the fence? Or can the same technique be done for the corner post without doing an N brace.
@brandoncaldwell95
3 жыл бұрын
This is end to corner sections. Around where i live its a pipe and 2 nails for the top. The tension wire has a pipe between the posts thats twisted tensioning the wire.
@MrFrozensmoke
3 жыл бұрын
@@brandoncaldwell95 i did H braces on the corners, with tension making the N.
@MrFrozensmoke
3 жыл бұрын
Almost a year ago now.
@rvp1948
13 жыл бұрын
The "gear" cost less than $3 .... leave them in.
@kaseycasece1340
3 жыл бұрын
NEVER USE SMOOTH WIRE FOR BRACING WIRE ALL WAY US 4 BARB WIRE FOR CROSS BRACING
@F479999999999
2 жыл бұрын
Explain your logic please?
@杨超-b3u
6 жыл бұрын
钢丝多粗??
@readynet4983
8 жыл бұрын
Hello ; is mortar mix a no no?
@fingersoup
11 жыл бұрын
Me too. =/
@timrogers4604
6 жыл бұрын
There are a few ways to build h-braces. Here is the way we do it - kzitem.info/news/bejne/ynhtn4V8hoGelWk
Пікірлер: 53