I was about to think that it was impossible to change these pads until I watched this video. Thanks a million dude.
@ricardosworkshop
16 күн бұрын
Glad I could help!
@skrsys
Жыл бұрын
I usually apply some copper anti-seize between the clips and pads to avoid squeals
@pawwalton2157
5 ай бұрын
Also need to check, clean and lube the caliper pins. Check the caliper bin boots to make sure they are not damaged.
@tagle2818
3 ай бұрын
Yes or you'll be doing this again.
@ronh9384
6 ай бұрын
you need to Lube the sliding surface of the pads where they rub on the new clips you put on. You put the correct lube on so the pads can contract and retract as necessary to help prevent uneven pad wear.
@ricardosworkshop
6 ай бұрын
Great tip! Thanks Ron!
@resenese573
11 ай бұрын
Bro didn’t lubricate anything or brush off anything at all. It looked pretty clean so he’ll probably be fine but don’t be surprised if one pad locks up and the other gets ground to nothing.
@jaramilloman12
7 ай бұрын
Bro, I was taking the whole damn caliper bracket off…. This is way better… thanks big dog!!! I love your forscan vids.
@Lrod.mobilemechanic
6 ай бұрын
Hey bud, thanks for the instructional video, but I think you got your rotors on backward. You can google the explanation for it. But other than that, great vid 👌🏽 pretty straight forward job. Hopefully, by now, you've figured out how to compress the pistons with a screwdriver/prybar before taking off the caliper the to make the job a little quicker 🤙🏽
@ricardosworkshop
6 ай бұрын
Thanks Luis. These discs look directional but are not. I believe the directilnal part is the middle that fans out to catch more air. But these dont. They are straight in the middle.
@brentkhack6404
Ай бұрын
The inner pads with the "bunny ears", I think they don't make that style anymore.
@ygfromig
6 ай бұрын
why didn’t you clean anything?
@scottlyons6977
5 ай бұрын
Do people really just swap out pads and not do rotors??
@ricardosworkshop
5 ай бұрын
Yes. I've changed brake pads tons of times. But rotors only when they go bad.
@sofiasprincessplayhouse2584
4 ай бұрын
I thought you had to break the fluid line to retract the rotors then bleed the air out once done?
@ricardosworkshop
4 ай бұрын
Not if you don't let any air in.
@Paul-ji9gv
Ай бұрын
I draw fluid out from the reservoir with my finger over a soda straw.
@dougblack8933
4 ай бұрын
Do the fancy rotors really help with warpage? Can they be turned?
@ricardosworkshop
4 ай бұрын
They can be turned. And they do help with heat. Which causes warpage
@gabeslawncare9104
7 ай бұрын
What kind of brakes did you put on ceramic
@ricardosworkshop
7 ай бұрын
Honestly, i dont remember, but i probably went with the most affordable ceramic brand from local autoparts store
@Aflameyt
Жыл бұрын
no lube???
@ricardosworkshop
Жыл бұрын
No need on ceramic
@ronh9384
6 ай бұрын
@@ricardosworkshop you need to Lube the sliding surface of the pads where they rub on the new clips you put on. You put the correct lube on so the pads can contract and retract as necessary to help prevent uneven pad wear.you need to Lube the sliding surface of the pads where they rub on the new clips you put on. You put the correct lube on so the pads can contract and retract as necessary to help prevent uneven pad wear.
@dwayner6597
Ай бұрын
This is called brake slapping. Not the proper way to do brakes.
@ricardosworkshop
Ай бұрын
Lol... That's great. Thanks
@anthonyjbarbutojrbarbuto3107
Жыл бұрын
Junk wheel spacers
@ricardosworkshop
Жыл бұрын
Lol... they've been great... 4 years in.
@rkey1012
Жыл бұрын
Not the proper way.
@ricardosworkshop
Жыл бұрын
The clamp or what part?
@tokiyoee544
10 ай бұрын
Always the niggas with no profile photo talking ab the right way
@abdulwadood.8
Жыл бұрын
You need a new truck, a GMC Denali would be perfect
@jimmyboyjbh9334
Жыл бұрын
Maybe if he was experiencing some shrinkage in his sack area, he’s got a beautiful truck love those older f150s
@trinkladd
Жыл бұрын
Nice. Next time use old pad to push in both cylinders at once
@ricardosworkshop
Жыл бұрын
Yes! Great add... but my c-clamp wasn't big enough
@stevenjacobs713
3 ай бұрын
You can not get the c clamp in the center to push both. The plumbing is in the way on the back side .
@RatherBfishin
9 ай бұрын
Your tires balanced and aligned. Somethings off with that tire.
Пікірлер: 39