Thanks a lot sir!. This video helped me figuring out which was the correct position of those miniature spring levers after completely taking apart my shaver head.
@DavidLevi-k1
Жыл бұрын
Thanks for letting me know that it helped you! Good luck.
@DavidLevi-k1
Жыл бұрын
This video is about putting the blades back together after cleaning them. It is very rare for the need to replace the blades. I have seen the blades being sold on eBay. I hope this helps.
@DavidLevi-k1
8 ай бұрын
Cleaning is pretty simple: Use water & dish soap (UK: Fairy Liquid) and submerge the bladed part into the mix while the shaver is running. Then repeat, with clean water. In a few minutes; all blades will be cleaned! Note: You cannot dismantle the foils to access the blades.
@adelmagid1477
Жыл бұрын
Thanks a lot , it is working now with me Wish you all the best
@bign1667
Жыл бұрын
I find the middle blades are jumping out on me. I can pop them back into the Shaver and just power it on, and they still pop out. It's gotta be a manufacturing fault.
@DavidLevi-k1
Жыл бұрын
The 2 middle ones (Gold & Silver) MUST be put back in the right order! They both have 2 clips each. Therefore, FOUR clips/tabs, fitted side by side to slot into the bay. If any one is in the wrong order they will keep falling out. Also, the gold one is to the rear of the shaver, when holding it in your hand. I hope this help, but I fear you may have broken the clips/tabs.
@bign1667
Жыл бұрын
@WasteInkPads thank you for that info that's really useful info. I'll try and pull it apart and see if I can fix it using your video. There is alot of Amazon reviews of others having the exact same issue so I believe braun needs to address this as it didn't happen with my original and 2nd replacement blades. Issue my seems to he with my last 2 blades which typically break within 3-8 months but braun seems to he just replacing them.
@bign1667
Жыл бұрын
Yet to pull it apart but I think I know the fault. The gold blade has 2 silver metal hook tabs that hook onto the bottom foil blade. Over time it I think it bends or stretches getting dragged up and down your face shaving leaving enough gap to pop out. I still just need to pull it apart and bend it back towards the bottom foil blade so it has less free play but I think that's going to be the fix
@bign1667
Жыл бұрын
Update I fixed it!! Thank you 😊 The two outer foil blades keep the two inner blades from popping out. If the inner blades (gold and silver middle blades) pop out it's because their metal hooks have become bent and loose causing them to pop out. The fix: follow the video but bend the inner blades connected to the foils out again to be more secure with the outside foil blades.
@DavidLevi-k1
Жыл бұрын
@@bign1667 Bless you! Thank you for your comments. I am sure it will help someone.
@stevavls
2 жыл бұрын
Great video but it’s confusing when @ 2:03 you try to say you pull and they fall off the video skips. That’s the only issue but thank you for posting and helping out
@DavidLevi-k1
2 жыл бұрын
Thank you for your comment! Every question/comment will aid someone in fixing their problem. Sorry, that the video did skip at that point! The videos was made to help people to re-assemble the blades. There are 2 tabs on each side of the blade assembly - when these are pulled apart the assembly will eject out. Furthermore, the outer casing will only allow the blade to be inserted one way and not if they are turned 180 degrees.
@daliscwbys1
Жыл бұрын
I'm sorry, but I can't find these tabs you're referring to on each side of the assembly. I can't take the outer case off. Please show a picture or video of this.
@joemalvik
Жыл бұрын
@@daliscwbys1 I have exactly the same problem. I also cannot find the "tabs referred to, and don't know where to grab/apply pressure to "pull apart". All I can see in the video is fingers covering the sides. It's a great shame, because the inability to get the assembly out makes the advice in the rest of the video (which seems very useful...) essentially irrelevant. The reply to another comment below says "just pull apart the outside frame". But it is made of metal, there is nothing to grab hold of and I cannot figure how to pull it apart.
@TG383
5 ай бұрын
@@joemalvik me too. I can pull the sides apart but it is still attached to the short sides. Guess ill need to buy another head
@louisestrada9991
Жыл бұрын
I am confused? By taking apart the razor cartridge, where do I buy the NEW razor blades to replace the USED blades? How much & where do I buy them? Thanks!
@PaulOhDee
Жыл бұрын
Thanks for this video! I’m also having an issue at the disassembly stage. My bracket is metal and I can’t pull them apart like you have suggested in another comment - is your bracket plastic or is there a tab I should be able to press down to release it? Thanks again
@reinaldozayas8798
Жыл бұрын
thank you very good video
@DavidLevi-k1
Жыл бұрын
Hi, Thank you for your interest in this video! At 1:56 you will see that I pull apart from the sides. But the blades will not fall apart in this position! You need to have this top part facing down, so with gravity, the blades will fall apart! (It is difficult to film under the blades while pulling apart the sides!)
@daliscwbys1
2 жыл бұрын
How do you take apart,? You just said you pull it apart but then it skipped over how to take the silver part off the black part.
@DavidLevi-k1
2 жыл бұрын
If you look at 1:57 - just pull apart the outside frame and they all fall out. Another thing that I forgot to mention: When all the blades are pushed back in - they will only go in one way! If you rotate the outer frame - they will not (hold) into the frame and keep falling out! I hope this information helps you!
@DavidLevi-k1
2 жыл бұрын
At 3:16 I picked up the frame and made a WRONG statement! I said: "It does not matter which way you put the frame" the reality is, it DOES MATTER! If wrong way - then the blade will keep falling out!
@thematrix7225
9 ай бұрын
Is there a way to open the foil itself and clean the actual blades?
@DavidLevi-k1
9 ай бұрын
You can only clean the outer two and not the central one.
@thematrix7225
9 ай бұрын
I'm referring to the outer foils. Can you open up the foil itself to access the blades? Thanks
@DavidLevi-k1
8 ай бұрын
@@thematrix7225 Cleaning is pretty simple: Use water & dish soap (UK: Fairy Liquid) and submerge the bladed part into the mix while the shaver is running. Then repeat, with clean water. In a few minutes; all blades will be cleaned! Note: You cannot dismantle the foils to access the blades.
@ggarcia713
Жыл бұрын
The foils on the sides that are not coming apart for me, it’s the gold and silver bars that keep coming apart for me.
@DavidLevi-k1
Жыл бұрын
The outer silver (curved foils) should lift straight out. It is possible that dried debris is holding the foils down. The inner gold and silver bars, will not lift out as they have tabs underneath. It is not necessary to remove the inner bars. You can easily clean them with a brush or even under water. If the inners bars have fallen out and will not return - it is probably due to the tabs being broken. It may also mean that you are trying to return them in an inverted position and may need to rotate them and put then in the opposite position. I hope this helps.
Пікірлер: 31