Thank you so much for posting this. I tore apart my carb linkages without taking a picture. Then 1 month later when I go to put it back together, I had no idea. Out of the many videos that I watched, yours was the only one to show the process for getting it connected correctly.
@williamburris3878
13 күн бұрын
Gas prices are too darn high, especially for the good stuff!. So I'm on my way to the Flea Market,....already have a harness! No more repairs and all thanks to you. Soon be mowing for free, just gotta lube up the sickle bar and look for a, healthy one, at the Market! Keep up the greatly informative and many times, hilarious videos! LOL! Valuable stuff in numerous ways! Thank you, always enjoyable, another admirer, WJB. Nice, TORCH TOUCH!!!!!
@Marksracingengines
Жыл бұрын
I build race car engines for a living...but I couldn't make my generator run right after I cleaned the dang carb....thanks to your video I figured out I blew the dang jet across the shop when I was cleaning the carb 🤣🤣🤣! I watched and said "Hey there's a jet missing from my plastic float holder" went back out there and found it laying in the floor lmaooo! Thank's buddy! subscribed...and if ya ever need big carb tuning help like Holley, I'm your guy lol
@jameslufrano4001
Жыл бұрын
Thanks, I’m a retired aircraft maintenance guy trying to learn a new motor. You been a big help.
@deancarder5829
Жыл бұрын
For months I thought my parts store was just being a pain over those numbers. You helped clear up a lot of frustration. Thanks again for your videos.
@LVBeatzMusic
Жыл бұрын
I love the humor you incorporate!
@shawnlucas7851
Жыл бұрын
My old Toro 1438 blessed it's oil sump with 87 about 10 years back. Wish I knew this then, I'd still have it runnin.
@pocketjock
Ай бұрын
Forgot to hook up the solenoid wire. Cleaned the carb and it wouldn't start so I watched your video. Runs great thanks
@Old600Rusty
10 ай бұрын
I would think you could also grind down that choke plate on that same corner.
@LucyZamb-z5b
Жыл бұрын
I did work with a guy who liked the Nikki carbs.... I think he was huffing carb cleaner
@RaleysSmallEngines
Жыл бұрын
🤣 🤣
@bobrogers2179
Жыл бұрын
I always buy aftermarket.... I look for the carburetors that have a center bolt on the bottom of the bowl instead of 2 Phillips screws on the top of bowl. I really like the ones with a plastic elbow fuel inlet too. I ALWAYS TRY TO REPLACE NIKKI STYLE WITH WALBRO STYLE EVERY TIME. IF I CAN. THANKS FOR YOUR VIDEOS... I ALWAYS LEARN SOMETHING
@ackack1
Жыл бұрын
You are absolutely right about ordering the Walbro style LMT 5-4993 with the bottom bolt. You have to look closely because some offerings are labeled as LMT 5-4993 but are the Nikki style with the Phillips.
@wabfil
8 ай бұрын
What if the carb that came with the thing has the two screws instead of the center bolt with the actuator thing...can you still use it?
@RaleysSmallEngines
8 ай бұрын
Shor answer is No. 2 screws on bowl is a Nikki style. You want a Walbro style carb. The only thing holding the bowl on is the solenoid. Thanks so much for watching and commenting friends
@The_Scatterbrained_Idiot
Ай бұрын
Thanks Raley. Old mower revived in a jiffy. Subbed.
@lindseyloo6619
2 ай бұрын
Man thank you so much. You single handedly made me a small engine mechanic haha ❤
@CHICAGOHAND
10 ай бұрын
My WALBRO does it also...Been driving me crazy for years now even after rebuild.
@chrisb.1301
6 ай бұрын
Your walbro fills up with fuel? Is it a legit walbro or the cheaper version of a walbro?
@bassinbillRC5300
4 ай бұрын
good step by step instructions. Will follow these once I get my fuel filter, air filter and carburetor parts in from ebay.
@RaleysSmallEngines
4 ай бұрын
Thank you, hope our video helps you.
@chrisgarland2272
Жыл бұрын
I have started following your advise on this and made a huge difference in repair time. Thank you!
@dogsandwich77
Жыл бұрын
You had me at "you can't run that on a gravity feed system. Wanna bet?"
@RaleysSmallEngines
Жыл бұрын
😆 🤣
@wabfil
8 ай бұрын
Saying o-ring first about the jet is very helpful.
@Ocean_breezes
Жыл бұрын
Great video. Thanks.Had same issue on my LT2000 tractor, 21yrs old.18hp Intek Smoking like hell, stalling out. I thought engine was screwed. New carb, fuel shut off , clear filter, change oil. Now runs perfect. No smoke.😊 BTY, the $25 carb saved me from buying a new $2500 tractor. Yee ha!
@tonydelovski8088
Жыл бұрын
$25 carb? Can you share where you got it from? A link would be great.
@ChristopherJones16
Жыл бұрын
@@tonydelovski8088 he bought the cheap knockoffs which youll have a 50/50 chance of it working or not. Buying the real McCoy B&S Carb will burn the wallet $100-$115 but i guess is guaranteed to fix it. Hopefully at that price the carb will never surge again or give us any problems.
@frogfoot198
Жыл бұрын
I have to write and say thank you so much sir. My mower is a Craftsman with the exact same engine and was suffering in the same way too. I ordered the Walbro, switched it out with that sorry butt Nikki, changed my oil to get the gas out of the engine, and now it runs like a new mower again. What a relief to my mind. Thanks again T-Bone!
@RaleysSmallEngines
Жыл бұрын
Awesome!!!! Glad our video helped you. Thanks for watching and commenting my friend.
@khoale1537
10 ай бұрын
Where did you order your Walbro part? How do you know which style NIKKI or WALPRO by looking from outside of each carb? Thanks
@RaleysSmallEngines
10 ай бұрын
Here is a link to it amzn.to/3FZqQms The Nikki has 2 screws holding the bowl on, the walbro just has the solenoid holding the bowl on.
@khoale1537
10 ай бұрын
@@RaleysSmallEngines Thank you! I noticed that the NIKKI style carb has two screws on the side bow while the WALBRO carb has only one screw (or the solenoid) at the bottom bow, please confirm.
@MichaelLitwak
6 ай бұрын
@@RaleysSmallEngines One commenter at that Amazon link wrote "this part number is, in fact, a Ruixing part number that is Walbro Style". For what its worth.
@BritishBeachcomber
Жыл бұрын
My Suffolk Colt Briggs and Stratton cylinder mower built in 1965 lasted 45 years with no repairs needed. Still going strong when I sold it.
@andrewdickson9964
8 ай бұрын
👌 good job fixing that nikki there as good as the bowl screws
@krzysztofslipecki4584
7 ай бұрын
Oh man, tons of thx for this hint. I replaced crappy Nikki carb with rebuild Walbro. Its like night and day. Walbro works like charm, no surging, cloggs, leaks ...etc. God bless for your great work!
@RaleysSmallEngines
7 ай бұрын
So glad our video was helpful my friend. Thanks for watching and commenting from T-bone and Mrs T
@rigsby556
4 ай бұрын
i have a swisher pull behind trail mower I use with my ATV, I have had a lot of trouble with the carb. I already added a fuel cut off to keep it from flooding so easily, a new filter because the factory one didn't do anything hardly. vie already ordered the new carb you showed and cant wait to get it put on there. great video & thank you
@RaleysSmallEngines
4 ай бұрын
Awesome, thank you.
@dogsandwich77
Жыл бұрын
New subscription, right here. That was the most honest, reasonable, non-sugar coated video ive ever seen. It's not biased, it's the truth. And it's fuct up but you're right. My only question is, can I achieve the same effect with a MAP torch?
@TheRustyRooster
Жыл бұрын
That is the best fix ever on a Nikki
@RaleysSmallEngines
Жыл бұрын
Thanks Rooster
@davidturley7633
6 ай бұрын
Thanks for this video I took your advice and went with the Walbro. Runs great. Did the same thing with the fuel lines too. I have a Troy Built Pony with the Briggs 17.5 horsepower and this worked great.
@beanolatte2682
Жыл бұрын
I found the nitrile o-ring kit from harbor freight has the o-ring that fits
@RaleysSmallEngines
Жыл бұрын
Awesome, sorry it will not last. Yep I've tried. Chunk the carb and get a Walbro. Thanks so much for watching and commenting my friend.
@tinkeringtaylor3053
Жыл бұрын
Definitely a 👍up T-Bone , well done
@RaleysSmallEngines
Жыл бұрын
Thank you
@matersworkshop6123
Жыл бұрын
That looks so simple to do and easy
@timlong2417
Жыл бұрын
I rebuild Nikkis everyday at my shop. If you know how to clean it thoroughly, very easy and works great
@RaleysSmallEngines
Жыл бұрын
That's great 👍🏻
@JM-yx1lm
Жыл бұрын
Ya and that's exactly the problem. It's a junk carb but here you are defending them. The walbro is a simple design and holds rpm far better than the Nikki.
@RaleysSmallEngines
Жыл бұрын
@@JM-yx1lm yep
@philliphall5198
Жыл бұрын
It’s not a problem to rebuild them , it’s the price of the dam kit that pisses me off
@coleramus561
Жыл бұрын
@philip--there's a Kohler rebuild kit for Nikki that's about $15 that has the O-rings you need
@denniscoss933
Жыл бұрын
T-Bone the mower I have is a lt 2000 and I will order a walboro as soon as I can i hope it solves my issue 😅
@iphone3gsdivine
11 ай бұрын
Did you order one?
@Pappy45
Жыл бұрын
Thank you for details & Part Numbers!
@BritishBeachcomber
Жыл бұрын
I always fit a hyper filter on everything that comes through my shop. Need longer fuel hoses and get the filter angle right or it can fill with air, but works a treat. And you can see when it's getting dirty.
@RaleysSmallEngines
Жыл бұрын
Awesome, I only use the 10352 Rotary filter. Hasn't failed yet. Thanks so much for watching and commenting my friend.
@JungleBobRepair
Жыл бұрын
Its hard for me to sell my customers on the Walboro,but thats ok ill see them again soon.
@RaleysSmallEngines
Жыл бұрын
I understand. I ask them "Do you want China junk? Or do you want me to fix it right?" And then I say... " have you priced new mowers lately?" 😆 works every time
@phobes
11 ай бұрын
Subbed! 2020 Craftsman T110 wouldn't start, narrowed it down to fuel delivery problem. Your recommendation to switch to a Walbro will probably save me from having to deal with this again in the future, much appreciated!
@rogermcdonald1607
Жыл бұрын
Nice video T-Bone. The 2 cameras worked well with great close ups! I wonder how many engines have been wounded because of Nikki carbs. The Walbro swap looks like the way to go.✌😎🇺🇸
@RaleysSmallEngines
Жыл бұрын
Thank you my friend, glad you liked it.
@LVBeatzMusic
Жыл бұрын
The aftermarket Kipa Nikki carb is really good bang for buck, just incase you don't have a Walbro hangin around.
@rauljr9869
Жыл бұрын
Great video, very educational keep em coming!
@rayburnett3066
9 ай бұрын
I take off the carbs like you do
@MichaelStone-dn3uz
2 ай бұрын
Your a genius! I know about engines and that change over was genius and all the tips and tricks that is pretty cool. Thanks for sharing part numbers and brands. I have made a couple of mistakes in the past when putting things back together. Once was a linkage issue. I couldn’t tell that the spring was broken in it’s coil over linkage. I had a surging problem with it afterwards and I finally asked the guys at my local John Deere dealer and one of them said that it sounds like a linkage issue and that I should check the spring that slides over the link and attaches to the governor. I did it and found the spring was broken so I went back to JD and replaced it and problem solved. No more surging. I don’t understand how a spring can prevent surging when there’s already a link in place from the carb to the governor?
@dannyhager9767
Жыл бұрын
Great video - great guy!
@RaleysSmallEngines
Жыл бұрын
Thank you
@papymuzo8122
Жыл бұрын
Thank you good day from France really good video.
@RaleysSmallEngines
Жыл бұрын
Thank you
@MikeJohnston-vj9ck
Жыл бұрын
Thanks my cub cadet 33 walk behind had a niki carburetor flooded cylinder after watching I rebuild niki with parts and it happened again so I bought a Walboro carb and now it runs like new
@RaleysSmallEngines
Жыл бұрын
Awesome, good job my friend 👏
@seanwatson7075
Жыл бұрын
good and accurate knowledge 👍
@hblide
Жыл бұрын
great vid...very informative. Funny also! thanks for all you do T-Bone.
@RaleysSmallEngines
Жыл бұрын
Thank you brother
@butler386
Жыл бұрын
Fabulous information. Thanks for the videos.
@steamboatwillie935
Жыл бұрын
She was a drinkin a lot of Kool-Aid ! 🛢 I like the Walbro swap, & agree about the cheap fuel filters. Pretty much pointless.
@RaleysSmallEngines
Жыл бұрын
Lol Too Funny. Thank you, yes they are.
@alandust2188
Жыл бұрын
Where did you get your hat? thanks for the video!
@RaleysSmallEngines
Жыл бұрын
That one is made by.. Sunday Afternoon. The other hats in my other videos are Panama Jack hats
@22hfang
11 ай бұрын
Hi Raley, I'm replacing the Nikki carb to a walbro also. I have a snapper rear engine 12.5 Briggs but I don't need the backfire solenoid. What size screw do I need to replace it?
@RaleysSmallEngines
11 ай бұрын
I recall @bssmallengines did a video on that and he explains what to use. Tell him T-bone sent you in his comments.
@Rebel9668
4 ай бұрын
Kohler has a kit for that same carb that comes with a new jet and O-ring that the Briggs kit doesn't come with and it's only about $20. I just bought an aftermarket carb that came with a manual shut-off switch, extra fuel line, clamps, plug, extra gaskets, etc. for $29 and it works just fine. If it lasts another season I figure I still came out ahead as my mower is on its 14th year now and didn't figure with it being that old that I want a $110 OEM carb from Brakes & Scrappum. In the meantime I'm putting back a little every week so that when my mower does give up the ghost that a new mower ain't gonna be so painful to my wallet, lol.
@tracykingston9668
27 күн бұрын
Briggs and Scrappum reminds me of when I was working at repair shops ; retired now, but I always called them " Briggs and StrapOn " 🤣😁.
@robertmailhos8159
Жыл бұрын
I have a Niki carb on my poulan XT mower 😮
@planetmoving9180
10 ай бұрын
One bad leaking carb can ruin the whole damn engine. I have exact same mtd mower. Been Wondering where my gas was going. Seen gas leaking from the breather tube where it attaches to the intake. Put on china nikki knock off. Opened oil dran plug and 87 octane coffee raced out. Put in new oil. Ran it and it still floods and leaks gAs past the carb. Will look to do thus swap. Matching Part numbers make it all possible.
@Mrs.T-bone
4 ай бұрын
You could install a manual in line fuel shut off valve between carb and filter temporarily so you don't lose all you gas.
@TheMrDrMs
Жыл бұрын
Just got my Genuine B&S 594593 - I guess the key word you said is Walbro STYLE as this model number is a Ruixing not a Walbro. Eitherway I suspect this will be better than a Nikki. Thanks!
@johnstaunton5522
3 ай бұрын
Another awesome video
@RaleysSmallEngines
3 ай бұрын
Glad you enjoyed it
@dosstheboss100
2 күн бұрын
I do this with any mower with a nikki only issue I've ran into when buying the amazon/ebay carbs sometimes I have to drill the pilot jet out or they surge on the larger engines like the 19hp . Idk they would require a different part # than you listed or if its just from the cheap carbs because it doesn't always happen
@JimHinsey
Ай бұрын
Do you have a video for a B/S opposed with a Nikki carb and pump change over to a Walberg?
@jamescole3152
Жыл бұрын
Why the hair sized choke wire? I don't understand why it is needed...
@SiteReader
2 ай бұрын
Thanks for video. The float on my Nikki 698945 carb was sagging just like this one. I tried the heat gun method but it didn't bend much. I used more heat and ended up losing alignment on the journal holes that the pin goes through, so now float will not drop. (So be really careful and patient if you try this.) My 28" Snapper rider has always started on first pull until the last time I washed it down, and then no-start, even after days of dry out. First thought it was electrical, but I get spark and have the right resistances on coil and new plug. Will not start even with safety harness wire pulled off coil. So now I think it's fuel problem. I have had the gasoline in oil problem for years. So maybe the carb finally gave out? Or, did water somehow get in the gas? Today I drained everything and washed out gas tank, but don't have a working carb to test out. I ordered a $21 replacement carb on Amazon. It costs about the same as a new float from Briggs. If it doesn't work, I guess I'll have to try the $109 Briggs genuine replacement carb.
@AllenDickenson
Ай бұрын
There are some good cheap Chinese copies on Amazon from $18-$30. I use them all the time. Good video!
@AllenDickenson
Ай бұрын
The $20 walbro clones are better than a stock Nikki
@xcpw72x
Жыл бұрын
i have an 06 Briggs Intek V Twin with a single barrel Nikki carb. wondering if i can swap it out for the Walbro.
@RaleysSmallEngines
Жыл бұрын
Very possible, but will probably have to drill out jets to give enough fuel for a twin cylinder
@knighthawk86855
Жыл бұрын
Great job.
@RaleysSmallEngines
Жыл бұрын
Thank you
@jamessanders7408
5 ай бұрын
👍
@Big_Johns
Жыл бұрын
Good job T-Bone, I don't much care for the Nikkis either buddy. Hey Mrs T-Bone 👋
@RaleysSmallEngines
Жыл бұрын
Mrs T-bone says hello. Love ya brother
@Big_Johns
Жыл бұрын
Thanks brother, love y’all too. 🙂❤️
@robcole332
Жыл бұрын
Another great one
@jameslund221
3 ай бұрын
Nice work. Does my craftsman lt2000 have a Niki carburetor it’s a 21 hp Briggs 2004 model?
@bassinbillRC5300
4 ай бұрын
Thanks!
@RaleysSmallEngines
4 ай бұрын
Wow! Thank you Bassinbill, so nice of you
@RaleysSmallEngines
4 ай бұрын
Wow! Thank you BassinBill, so nice of you.
@bassinbillRC5300
4 ай бұрын
@@RaleysSmallEngines I have a basement workshop. Half is for electronic repairs. The other half is for mending, or maintenance of bicycles.
@ralfkessler
5 ай бұрын
I have a niki carb with horizontal shafts and can not find a walbro replacement. Is there one not listed????
@FireRescue884
Ай бұрын
Normally I put the amount of fuel I need for the job, but this time I filled it slap full ! Sure as chit, it sat overnight and literally filled every inch of that motor with ⛽️ and all over the shop floor. Had no clue these cub cadets had this issue. I ordered one from Amazon, should I rebuild the new one with that kit to avoid this problem again ? Or will it do the same thing again down the road 🤔
@chrisc548
Ай бұрын
How do you adjust the idle down a bit?
@ededmund5685
Жыл бұрын
GOOD VIDEO THANKS Ed Loretto Ontario Canada
@RaleysSmallEngines
Жыл бұрын
Glad you liked it my friend. Thank you
@dustindahlinger9446
4 ай бұрын
Can you replace the carb on the 19.5 hp B&S 502cc engine with that same Walbro carb?
@KillerB101
Ай бұрын
Why does the intake gasket block half of the port? The gasket between the head and the intake runner on a 500cc single cylinder.
@mr1pearl
Жыл бұрын
I think Rick Flair and his tag team partner 🐿 says it all woooooo !
@RaleysSmallEngines
Жыл бұрын
😆 🤣
@bobalvarez7425
Жыл бұрын
Hi, this may be a dumb question. But how I find the walbro replacement for the 594593 carburetor?
@RaleysSmallEngines
Жыл бұрын
594593 is the oem Walbro number. Look on Amazon they are about $100
@bobalvarez7425
Жыл бұрын
@@RaleysSmallEngines awesome, thanks for the fast reply.
@mark98070
6 ай бұрын
My Intek 12.5 does not have a fuel solenoid. Is there another model Walbro that doesn't require the wire? Perhaps a different model Walbro without the solenoid?
@gonzalez519
16 күн бұрын
How do I know how much to adjust the air fuel mix screw? Also, I set it up so it idles at low rpm then when I mow the lawn for a while and try to set my rpm’s down with the speed cable it never goes back to low rpms. 🤷🏻♂️
@603Aviation
5 ай бұрын
What about applications without the fuel solenoid?
@RaleysSmallEngines
5 ай бұрын
Remove the solenoid from the new carburetor and cut the tip off, then reinstall it.
@reece2182
8 күн бұрын
So i just bought a mower dirt cheap, i want to get it going to do my yard. It looks like someone at some point did all of the conversations you did in theis video, the shut off, the same filter and the walbro carb. Although the previous owners definitely did let the thing sit with bad gas, the walbro carb was full of jelled up fuel. It was hydrolocked with fuel, i cleaned the carb but could not get the main jet out but its wide open, carb clean straw goes all the way through it. Now im still having the same issues, it will quickly hydrolock on its own fuel, its got fuel in the oil, oil coming out the pcv, oil out the exhaust. Should i just buy another new carb? Or is this one too far gone and will have other issues?
@RaleysSmallEngines
8 күн бұрын
Good effort my friend. Just replace the carburetor again is the best solution in my opinion. Thanks for watching and commenting my friend.
@calgreco8607
5 ай бұрын
My sons rear rider snapper doesn't have that thing on bottom of fuel bowl with wire? What is that? It's flooding out the spark plug hole so I assume it's the float bowl.
@mattarmstrong9626
4 ай бұрын
My two year old b&s 19 horsepower came with a Ruixing carburetor according to b&s. Are they any better than the Nikki? And why in the heck did they change the top from using bolts to clamp it on to one that has to have the bolts completely removed to take it off? The two bolts on the back are dern near impossible to get out.
@Goodellsam
18 күн бұрын
Cool
@peanutsmith1462
5 ай бұрын
I have an older 2000 model briggs & Stratton 19.5 hp that I need to replace the carburetor do you have a recommendation for me please sr
@RaleysSmallEngines
5 ай бұрын
Same as one in video should work
@rubendfernandez4747
4 ай бұрын
Nice video tks sr
@samtate1260
Жыл бұрын
My craftsman junk says briggs and Stratton on the carburetor what kind of carburetor is it?
@RaleysSmallEngines
Жыл бұрын
Does it have 2 screws holding bowl on? If it does it's Nikki
@samtate1260
Жыл бұрын
@@RaleysSmallEngines yeah it’s a junk same one that broke in under 20 hours so far, no problems with the carburetor yet
@joestihl2234
5 ай бұрын
I have an old intek with the nikki,its 2009 toro xl440h,never had any trouble with it,no fuel tap,maybe i just got a good one?
@rickyrickharris4908
11 ай бұрын
Whats that lil jet thing at 5:27 that fell out of the float and why dnt i have that peice hiding anywhere?? PLSS HELP!
@kevinanderson9093
3 ай бұрын
Will this carb work on a Briggs and Stratton 17.5 hp.
@bea_sti
4 ай бұрын
Do you have a part number for a warlboro carb for my HUSQVARNA YTH22v46???
@markstanchin1692
Жыл бұрын
Hello, so I purchased a genuine OEM Briggs & Stratton carburetor online thru Amazon. Around 95.00 Part number on the box is 594593. Wanting to replace Nikki carburetor that’s surging. The Actual part on the carburetor is 595210. Is that correct? The part looks right The fuel solenoid is shorter then the Nickie I’m not sure if that makes a difference. Thanks!
@RaleysSmallEngines
Жыл бұрын
Don't worry about that solenoid, no matter what they look like they do the exact same thing. Just do the modifications shown in the video.
@markstanchin1692
Жыл бұрын
@@RaleysSmallEngines Thank You!!
@josiahrice6810
Жыл бұрын
My dad has a similar fix for cellphones, he recommends a sledgehammer but the phone will never be a problem again.
@RaleysSmallEngines
Жыл бұрын
🤣 🤣 🤣
@chipofftheoldblock8090
Жыл бұрын
T-bone how come you wouldn't gring down the choke flap instead of the plastic
@RaleysSmallEngines
Жыл бұрын
Because the choke wouldn't work as good and would not close on to the body of the carburetor.
@Pete.Ty1
Жыл бұрын
👍👍👍Thank you.
@SaintThomas2009
Ай бұрын
What makes the Walbro better than the Nikki?
@denniscoss933
Жыл бұрын
The nikki carb can be rebuilt and you bettet have a ultra sonic cleaner if the motor sat for anywhere neat a yeat ot two wirh gas. I have 5 of rhem that are being a pain in the butt. I will be switching to a walboro as soon as I get the money to. 😅
@fredericcarpentier-t5z
6 ай бұрын
Hello Sir! 😀 I'm french and I really wanted to thank you for this video which helped me a lot to understand that I needed to change my Nikki carburetor for a Walbro. My only "problem" is that I have a B&S motor Series 3 130 (344cc) and the model number is 21B807-0138-B1. Do you think the model you have showed (594593) will be ok for my motor or do I need an other one? Please just an other little question from the rookie I am 😅: You don't talk about it in your video: no adjustment is necessary on the screws of the new carburetor? Is it "plug and play" ? Many thanks for your help. Regards from France. 😉
@RaleysSmallEngines
6 ай бұрын
Glad it helped you. Use the one I showed in the video, it's plug and play. It should work just fine. Thanks for subscribing, watching and commenting my friend.
@fredericcarpentier-t5z
6 ай бұрын
@@RaleysSmallEngines Many Thanks for your help! Kind regards from France 😀 😉
@MurphyMower
Жыл бұрын
Good video- just subbed
@RaleysSmallEngines
Жыл бұрын
Awesome, thank you
@anthonyhugger5447
11 ай бұрын
Thank you so much!!!!!!!!!!!
@charlesmason446
Жыл бұрын
I have a 24hp V Twin B&S. Would love to change the carb to something more dependable. Any suggestions?
@jafquist27
3 ай бұрын
I had my Nikki off today, for the third time this spring! Crank case was full of gas. I had known about bending the plastic float part, and did it a couple years ago. I am about to pull the trigger on a Walbro, and be done with playing with the carb, four, five, and ten times per mowing season! Do you have a video on re[placing the cam shaft on a that same engine? Everyone else seems to only show the v twin intek, not the single cylinder models, and they, show the process very vaguely. They use lots of jargon and assume I know all about the engine and small engine repair. Why would I watch their video, if I had all the knowledge already? Can you help?
Yes, I have a cam shaft video. They are all easy to do. Just scroll through my channel and you will see it. Thanks for watching and commenting my friend
@chefington0217
Жыл бұрын
If my current lawnmower doesn’t have a solenoid and I buy the one you suggest, how do I bypass the solenoid
Пікірлер: 245